Question about Mazda B2600

1 Answer

Recently a belt has snapped and not sure what the belt is for. I have a 2006 Mazda B2500 Turbo Diesel. Two belts run beside each other and are located infront of motor. The one which snapped is furtherest away from the motor. Have bought a new belt, would like to know what this belt is for? How to install it? Steve

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 143 Answers

Best bet is to get a chiltons manuel somtimes library carries it and will give a belt diagram in there to look at should be able to buy one for 20 bucks or so at the auto parts store try that first

Posted on May 24, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

At what stage does the factory reccomend a timing belt replacement?


most diesel timing belts need to be changed every 60 to 80 thousand miles alway worth getting checked as if it snaps or skips teeth it can cause serious damage to the engine

Oct 19, 2014 | Cars & Trucks

1 Answer

I need belt diagram for a Mazda Millinea s 2.3 with turbo. I need the belt that works the turbo


There is no belt that runs the Turbocharger. A Turbocharger uses the engines exhaust to spin a wheel that is attached to a compressor wheel.
Try this link for your correct belt diagram:http://lmgtfy.com/?q=Mazda+Millenia+s+2.3+belt+diagram

Dec 19, 2012 | Cars & Trucks

1 Answer

On a 2001 mazda bravo turbo disel when do I have to change the timming belet it's done 176000 ks


Hi there,

Without knowing which diesel engine you have, I'll have to guess that you have a 2.5L (B2500) - Note: the more detailed information you give us, the more accurate our answers will be :-)

As a general rule, cambelts (with tensioner assembly & seals) have a limited life and should always be replaced every 100,000km, or sometimes earlier depending on manufacturer. The reasoning behind this is that most engines will suffer major internal damage if the cambelt snaps (this is what is meant by 'Interference' engines). As the engine has to be opened up to carry out this service, it can be a costly maintenance. For this reason, it is also common to replace the waterpump at the same time (to avoid having to open up the engine again) as waterpumps have been known to fail beyond 100,000km.

The good news....if you DO have a 2.5L (B2500) engine, then this engine is a NON interference engine - which means, if the cambelt did snap, your engine would not suffer any internal damage, compared to interference engines.

Hope this helps.....


"If this has helped you in any way, please rate this solution"

May 07, 2011 | Mazda B2200 Cars & Trucks

2 Answers

One of the bearing, ac belt passon is broken.


maybe belt too tight, get new bearing for centre of idler pully = about 14 dollars australian

Sep 30, 2009 | 2006 Toyota Land Cruiser

2 Answers

2006 volkswagon timing belt jetta tdi turbo diesel


i can walk u through doing a t belt. But if u are not sure if u are able to do it DO NOT DO IT cause if u are wrong if cause a lot of engine damage.

Mar 22, 2009 | 2006 Volkswagen Jetta

1 Answer

Fan belt 1997 mazda 323


first of all you need to find the power steering adjuster you will find this beside power steering pump there is a locking nut on pulley slacken that then slacken off adjusters once you have done that you will be able to remove belt same applies for slackening alt belt make sure you slacken of locking bolt otherwise you will bend adjuster bolt.hope this helps you.

Jan 17, 2009 | Mazda 323 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...