Question about Toyota Camry

1 Answer

What is needed to install a motor regulator on a 2001 toyota camry

Posted by on

1 Answer

You have to remove the door panel, just to see
or get to things,motor,regulator etc.

Not a job I would suggest, if you have no auto
experience.

Sort of a learn as you go, on every car you have
to go inside the door on.

Not easy & you always get cuts, no matter how
you work. Those door panels are sharp & you
can not wear gloves & fit your hands in there

Posted on May 24, 2011

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1374 Answers

SOURCE: install motor/regulator to 2000 camry solara

It easy ! You need a philips2_bing.gif and flat screw driver,8" X 4" block of wood and a needle nose pliar.
Use flat screw driver and pry out the two or three dust covers for the arm rest screws then use philips and remove the screws. Next use the flat screw driver and pry out the black plastic mirror cover from the inside of the door. Pry out the switch panel ( aka master switch panel) with the flat screw driver and disconnect it. On the side of the door panel just above the striker is this plastic push pull typeof a hold in screw. Use flat screw driver to get it to move a little then pull it out with the needle nose. Depending on which door your doing if you have a map folder ( driver or front passenger door) in the door there are two more screw to remove on the bottom of the door.
Now the inside door handle is tricky it comes out in two pieces. Use philips and get the only hold down screw you see out.( you may have to pry out al ittle screw cover first) Now the handle cover is removed by placeing the flat screw driver on the rear of the outside of the cover top and on the outside rear bottom to release the tangs that are holding it onto the panel.Pry it out lightly you may have to place the screw driver over the top of the door release button and pry that way. Don't loose your cool its a pain but it will fall out. Once its removed unhook the panel.

Next lift the plastic cover and remove the six gold2_bing.gif bolts first(For motor and regulator) Then push the window down till you see the two bolts holding the window to the regulator .Remove them, BEFORE YOU PULL OUT THE MOTOR AND REGULATOR YOU WILL SEE TWO TANGS THAT HELP HOLD THE REGULATOR AND MOTOR TO THE DOOR MARK THE RELOCATION , NOW pull out the motor and regulator have an assistant hold up the glass while you place the two blocks of wood to hold up the window. Now order your regulator and installation is in reverse. Good luck kate. Keep me posted.
Comments:

Posted on Apr 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know the marker settings on my motor balance shafts


I use a manual. You really need to get one.Timing is a critical part of engines... Especially if it an interference engine.

Oct 07, 2016 | 2001 Toyota Camry

1 Answer

Window on driver's side quit going up and down?


Most likely the motor failed-LIsten for any sound-If you here sound then the regulator failed-if not the motor dumped-GL

Jun 23, 2014 | 2001 Toyota Camry

1 Answer

New electica motor and regulate only goes up not down


very poss. switch problem unhook conn at motor use jumper battery jump 2 wires to window motor then reverse one of these should put window down there fore the switch is the problem only other poss is no ground on that side of the switch

Sep 15, 2013 | 2001 Toyota Camry

1 Answer

How to roll down 97 Camry driver side window with bad motor?


normally you want the window up to access the motor and regulator but you can remove the window motor and try with a pair of pliers turning the gear manually

Jul 18, 2012 | 1997 Toyota Camry

2 Answers

How to replace voltage regulator on 1990 Toyota camry.


Assuming the regulator is inside the alternator, as most are,
you have to remove the alternator from the car,remove the
4 long bolts that hold the 2 halves together,then remove the
screws or bolts holding the regulator

I suggest you see if the regulator is avail
You may be better to go to an auto electric shop
that does just that, & you may be able to buy the
regulator there ,or wait while they install it & test
to see if it needs replacing.

May 30, 2012 | 1990 Toyota Camry

1 Answer

Driver side window wont roll up??? 1994 Toyota Camry


that model camry has a window regulator that is cable driven. it is very common for that cable to snap and not allow the window to close. it will likely need a window motor/regulator assembly.

Nov 24, 2009 | 1994 Toyota Camry

1 Answer

2001 camry rear driver window


ya if i remeber correctly you have to buy the whole thing as a unit but a cheap repair is to go to a junkyard and get one out of it this will save you money and it will teach you how to pull out without ruining your car ;]

May 18, 2009 | 2001 Toyota Camry

1 Answer

2002 toyota engine, oil sludgecaused my car to stopped and now needs overhaul


Complain to Toyota, they are fixing some of these car for free. Here is the explanation and the list of problem vehicles.

Oil sludge or black sludge is a solid or gel in motor oil caused by the oil gelling or solidifying, usually at temperatures lower than 100 degrees Celsius. Sludge can be a major contributor to Internal combustion engine problems, and can require the engine to be replaced, if the damage is severe. Sludge is usually caused by the presence of water in the oil, and can accumulate with use. Ways to minimize sludge production and accumulation includes performing frequent oil changes, using synthetic oil, and following the manufacturer's engine maintenance routine.
The following engines were reported by the Center for Auto Safety and/or their manufacturers to have a problem with sludge accumulation:

  • 1996-2001 Toyota 3.0 L 1MZ V6
  • 1996-2001 Toyota 5SFE I4
  • Feb 23, 2009 | 1995 Toyota Camry

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    27 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    75066 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7754 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...