Question about 1995 Ford Aspire

Open Question

1995 ford aspire, where is camshaft position sensor located?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

warlock61
  • 659 Answers

SOURCE: 1995 Ford Ranger 3.0 camshaft positioning sensor

it is called a synchronizer if it is damaged it should be replaced approx $120 can use a salvage part as long as it is the correct application

Posted on Nov 24, 2008

davesmith_37
  • 94 Answers

SOURCE: P0340 Code Camshaft Position Sensor


The Camshaft Position (CMP) Sensor detects the position of the camshaft in order to identifiy when piston No. 1 is on its compression stroke. The CMP sensor is used for ignition timing in the Ford DIS igntion system, but not in the EDIS igntion system. Both DIS/EDIS use the CMP signal for synchronizing the firing of sequential fuel injectors.

On the 3.0L vulcan engine, the CMP signal is generated by a single Hall-Effect magnetic switch, activated by a single "vane" spinning around by virture of a synchronized shaft which is driven by the camshaft. 

The CMP sensor & synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:

Posted on Feb 27, 2009

  • 43 Answers

SOURCE: P0344 Camshaft Position Sensor A Circuit Intermittent (Bank 1 or

The camshaft sensor is located right above the crankshaft pulley on the passengers side of the front cover of the engine. It will be a 3 pin sensor either gray or black in color. There is a pointer that is attached to the sensor and it is either gold or silver in color. There is also a recall out on this camshaft sensor. If the color of the sensor is black then it should qualify for the recall. If you get in touch with a Ford dealer they should be able to help you with your recall if the sensor is black since it is a safety recall. As far as your exhaust pressure sensor it is located on the front of the engine right by the heater core hose a little to the passengers side of the center of the front of the engine. there will be a tube attached to the bottom of the sensor that goes from it to the front of the exhaust manifold on the very front of the passengers side exhaust manifold.

Posted on Apr 11, 2009

emissionwiz
  • 75822 Answers

SOURCE: where is the speed sensor on a 1995 Ford econoline van

the sensor is located on the driver side of the transmission case

Posted on Jun 19, 2009

  • 85 Answers

SOURCE: Where is the camshaft position sensor on a 2000 Ford Explorer?

in the rear like where the dist would normaly be

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Edge. where is crankshaft position sensor located?


Hi Rusty, There's two links below showing the position of 2005 Ford Explorer Crankshaft Position Sensor and the 2008 ford edge camshaft sensor location. It seems like they're all in the same position, I hope this helps.....CHEERS
..
2005 Ford Explorer Crankshaft Position Sensor Location

2008 ford edge camshaft sensor location

Apr 02, 2016 | 2003 Ford Ranger

1 Answer

What is location of crankshaft position sensor on 2007 ford f250 with 6.0 diesel.


There are some GREAT pictures I think will help you find it. Go to http://www.ford-trucks.com/forums/1160636-camshaft-position-sensor-cmp-wiring-pigtail-replacement.html It is located under the subject of "Camshaft Position Sensor (CMP) wiring pigtail replacement"

Feb 28, 2015 | Ford Cars & Trucks

2 Answers

Where is 2003 ford focus camshafts position sensor


Camshaft Position Sensor
The camshaft position (CMP) sensor detects the position of the camshaft. The CMP sensor identifies when piston No. 1 is on its compression stroke. A signal is then sent to the powertrain control module (PCM) and used for synchronizing the firing of sequential fuel injectors. The Coil On Plug (COP) Ignition applications also use the CMP signal to select the proper ignition coil to fire. The input circuit to the PCM is referred to as the CMP input or circuit.
There are two types of CMP sensors: the three pin connector Hall-effect type sensor (Figure 25) and the two pin connector variable reluctance sensor

a452a319-2d08-4e59-9885-fe43b5fc7f61.gif

and next the location of 2003 ford focus camshafts position sensor
96d62950-03fc-4668-b3ad-dfa939f76b14.gif

Sep 13, 2014 | 2003 Ford Focus

1 Answer

I received a P0340 on my 1995 Nissan Altima. It says I need to replace the Camshaft sensor. The dealers say that my car does not have one in it and that it may be in the distributor itself. Is this true....


They may be right. I cannot find the part. here is what the manual says:


REMOVAL & INSTALLATION The camshaft position sensor is located inside the distributor. On some distributors, the camshaft position sensor is not serviceable (replacement parts may not be available separately). If the camshaft position sensor is serviceable, use the following procedure.

  1. Remove the distributor cap and wires.
  2. Remove the rotor.
  3. Remove the camshaft position sensor cap.
  4. Remove the camshaft position sensor mounting screws.
  5. Carefully remove the camshaft position sensor.

To install:
  1. Position the camshaft position sensor in the distributor and tighten the mounting screws securely.
  2. Install the camshaft position sensor cap.
  3. Install the rotor.
  4. Install the distributor cap and wires.

Sep 27, 2010 | 1995 Nissan Altima

1 Answer

1993 ford taurus, replaced all starting and charging componets still no spark to plugs. Checked all fuses and all fusible links. Replaced key switch, ignition switch,neutral safty...


The camshaft position sensor sends a signal to the PCM, powertrain control module. The PCM then determines spark plug firing. Could be the camshaft position sensor.

1996 is all I have
Camshaft Position (CMP) Sensor 3.0L (2V) Engine
The camshaft position sensor (CMP sensor) (12126):
  • is a single Hall-effect magnetic switch activated by a single vane which is driven by the camshaft (6250).
  • provides camshaft position information which is used by the ignition coil (12029) and the powertrain control module (PCM) (12A650) for fuel synchronization.
3.0L (4V) Engine
The camshaft position sensor (CMP sensor) (6B288) is:
  • a variable reluctance sensor.
  • triggered by the high-point mark on the LH exhaust camshaft sprocket (6256).
-----------------
3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder block (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder block.
Installation
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be obtained prior to installation of the replacement camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs when arrow on locator tool is pointed approximately 75 degrees counterclockwise from the rear face of the cylinder block. This step will locate camshaft position sensor electrical connector in the pre-removal position.
  1. Roatate Syncro Positioning Tool T95T-12200-A clockwise slightly. This will engage oil pump intermediate shaft. Push downward while adjusting Syncro Positioning Tool T95T-12200-A until the Syncro Gear engages the camshaft gear.
  1. When synchronizer flange is fully seated against block, the installation tool should be facing counterclockwise of engine centerline approximately 33 to 45 degrees.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (13-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.
824fa44.gif
Item Part Number Description 1 T95T-12200-A Syncro Positioning Tool 2 — Water Outlet (Part of Intake Assy) 3 9424 Intake Manifold 4 N602704-S Screw and Washer 5 12126 Camshaft Position Sensor 6 12A362 Synchronizer Assembly 7 12270 Hold-Down Clamp A — Tighten to 1.5-4 Nm (13-35 Lb-In) B — Tighten to 19-30 Nm (14-22 Lb-Ft)

Apr 04, 2009 | 1993 Ford Taurus

1 Answer

1995 Ford Ranger 3.0 camshaft positioning sensor


it is called a synchronizer if it is damaged it should be replaced approx $120 can use a salvage part as long as it is the correct application

Nov 15, 2008 | 1995 Ford Ranger Supercab

1 Answer

Where is my camshaft positioning sensor located


The CMP (camshaft position sensor) is located where the distributor would normally be.

Jul 01, 2008 | 1995 GMC Jimmy

Not finding what you are looking for?
1995 Ford Aspire Logo

Related Topics:

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...