Question about 2006 Suzuki Forenza

Open Question

Hey i had engine codes p0700 and p0705 n my 2006 forenza. p0705 meant my range sensor was bad. i replaced it myself. all the gears are in correct place now but sometimes when i come to a sudden stop, the car jurks.

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1 Answer


You do not need to "calibrate the computer" when changing the trans. range sensor. If the dealer is telling you this, it is because they want more of your money. Just buy the sensor.

Posted on Feb 15, 2010

  • 196 Answers

SOURCE: have a reading of p0700 and p0705. also. driver

a p700 code is a general trans code you need an DRBIII scanner to read the code to narrow it down,there are plenty of write up on cleaning up your netural safty switch which is usually the cause of the reverse light problem so you may want to give that a shot,hope this helps.the 705 code usually leads to a faulity netrual safty switch

Posted on Mar 19, 2010

  • 10319 Answers

SOURCE: suzuki forenza

I do not have a code book or chart for your model car but all codes with 700 are pertaining to the transmission

Posted on Apr 03, 2010

  • 1150 Answers

SOURCE: took my 2006 suzuki forenza

PO700 transmission range sensor
PO705 transmission range sensor circuit

Posted on Sep 16, 2011

  • 17970 Answers

SOURCE: want to locate censor p0705 on a 2006 suzuki

DTC P0705 - Transmission Range (TR) switch circuit malfunction (short to power supply)

• Two or more range signals are input from the TR switch for 12 s or more.

Diagnostic support note:
• This is a continuous monitor (CCM).
• MIL illuminates if TCM detects the above malfunction condition in two consecutive drive cycles.
• PENDING CODE is available.
• FREEZE FRAME DATA is available.
• AT warning light illuminates.
• DTC is stored in TCM memory.

• TCM malfunction
• Short to power supply in wiring harness between TR switch terminal A and TCM terminal 1D
• Short to power supply in wiring harness between TR switch terminal E and TCM terminal 2C
• Short to power supply in wiring harness between TR switch terminal D and TCM terminal 2B
• Short to power supply in wiring harness between TR switch terminal G and TCM terminal 2E
• Damaged connector between TR switch and TCM
• TR switch malfunction

Inspect swtich harnesses and test with OBD scanner reader tool.

Posted on Sep 30, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Will the range sensor make the vehicle lose spark

no, (mostly) the range switch in the tranmission
tells the PCM (TCM) what gear you've selected.
but if it might if it range shows starting in gear.

why not scan the PCM and fix what it shows is bad.
why not post all DTC errors. let folks tell you what checks are next.
crank for 5 seconds, release key, put eyes on scan tool
see all those DTC errors. P03xx or others. like P0700 or?
or immoblizer? errors?

May 12, 2015 | 2006 Suzuki Forenza

1 Answer


try replacing the TCM as code p0700 refers to specifically and it puts the light on.

Feb 15, 2014 | Chrysler Sebring Cars & Trucks

2 Answers

I just want to find an accurate and complete list of codes for my 98 Cherokee Classic 4.0 liter 2wd. Just installed ScanGuageII reader and get codes P0700, P0705, P0463. Only P0463 is in the Chilton manual...

Hi, you can see a full list of Jeep DTCs here:
Your engine light will probably return immediately after clearing the codes until the P0700 is rectified. The 705 indicates your range sensor is out of adjustment or broken. The range sensor is mounted to the side of the transmission where the cable attaches. It may be adjustable. Normally, when the range sensor fails, the starter will not turn, because the sensor provides the park/neutral safety interlock to ensure the transmission is not in gear. Also, the range sensor usually includes the backup light switch. I usually adjust the sensor by putting the transmission in reverse, turning the key on, loosening the switch, and rotating it until the backup lights come on. Please let me know if you have questions and thanks for using FixYa.

Mar 31, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

I have a 2004 dodge neon sxt, the check engine light is on and when i drive it the exhaust is loud and the car accelerates horrible. I get it up to 30 max and it takes a little while. Got it diagnosed and...

If u have an exhaust leak (loud sound) that will affect a lot of the sensor readings. The O2 sensors will not read properly either & set codes. If the leak is large enough u will lose power & the trans wont work properly either & set codes. Just because u have a code, doesn't mean the part is bad. Start w the basics. If there is an exhaust leak, fix that 1st & clear the codes.

Mar 12, 2017 | 2004 Dodge Neon

2 Answers

Suzuki forenza

I do not have a code book or chart for your model car but all codes with 700 are pertaining to the transmission

Apr 03, 2010 | 2006 Suzuki Forenza

6 Answers

On my 2007 suzuki forenza the check engine light came on. i had it troubleshooted at autozone, and the computer indicated the transmission range sensor out of position. where is it located?

no such code on that car, auto zone uses global testing which pulls universal codes, so that code means someting different for the suzuki, need to have it checked by the dealer or a shop that has import software, or post the code # and i can translate it into import code, good luck.

Nov 28, 2009 | 2007 Suzuki Forenza Sedan

2 Answers

2001 pt cruiser engine light code P0700/ p1284

well p0700 is a transmission code and the related repair on alldat is a error in tcm module! sounds like a bad computer but i couldn't say unless i tested it myself! sorry for lack of info and the other code was not in the list but there was a 1294 and that is a "target idle not reached" so i would be looking at the throttle body and clean it and make sure nothing is binding and aso vacume leaks throught the motor! good luck

Sep 20, 2009 | 2001 Chrysler PT Cruiser

Not finding what you are looking for?
2006 Suzuki Forenza Logo

Related Topics:

466 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides