Question about 1995 Mazda B-Series

1 Answer

I have a 1995 b400 v6 2 wheel drive pick up. Both my brake lights went out all of a sudden. I still have parking lights, turn signals, reverse lights, but no brake lights. I still have brakes. I just put a new brake light switch at the brake light pedal with no results. What else can I try?????? Chris

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Mazda Master
  • 1,453 Answers

Might just be the brake light fuse is blown.

Posted on May 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signals, brake lights, reverse lights all blinking when turn signal is activated


The right tail light assembly is not grounding the chassis. Pull the access panel off and look for the ground points from the wiring harness and the assembly. Undo the nuts a bit and tighten them again. That should restore the ground and clear the problem.

Feb 22, 2015 | Subaru Forester Cars & Trucks

1 Answer

My 1995 chevy s10 brake lights reverse lights high mount light all went out and cant find out why


Check connection on frame that operate rear. Do the rear parking lights work, turn signals?

Dec 26, 2013 | Chevrolet S 10 Cars & Trucks

1 Answer

Brakes failed, went to floor, brake light came on what now?


Check the inside of the tires to see if you find any brake fluid, some flex pipe going to the front calipers or rear wheel cylinder might have busted.

Jun 22, 2012 | 1999 Ford Escort

2 Answers

My 1995 Chevy Tahoe brake light switch wont stay in position and the brake lights stay on. I replaced the switch and had the same problem.


Brake Light Switch REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Disable the SIR system (if equipped).
  3. Remove the clip (R/V Series) or unclip the switch (C/K Series) and unplug the electrical connector from the brake light switch.
  4. Remove the switch.
  5. Installation is the reverse of removal.
prev.gif next.gif

Oct 07, 2010 | 1995 Chevrolet Tahoe

2 Answers

Have a 1995 jeep cherokee that both brake lights went out. all other lights working, signals, reverse, but not brake lights. fuse? have no owners manual. also a right hand drive


Most likely the fuse, if the fuse is good, then check the brake light switch, that is under the dash, near the top of the brake pedal.
Press on the brake pedal with your hand and see if the button is popping out, if not, tap on it and see if it pops out, if not, replace it.

May 05, 2010 | 1995 Jeep Cherokee

1 Answer

My parking brake light stays on and my brakes seem to be sticking as well.1995 Chev.pick-up,I pulled the rear wheels off and found I could still rotate the drum without any sticking or rubbing. Could this...


it sounds like the front brake slides/or pins are sticking i would service front calipers and apply lube where needed.For the brake light you would need to check the brake fluid level sensor turn it counter clockwise 1/4 turn and clean with brake clean if that doesn't work unplug the sensor and if light goes off replace sensor for brake fluid level.Also make sure parking brake is totally released.

Mar 23, 2010 | 1995 Chevrolet C1500

1 Answer

85 chevy 3/4 ton pick up .Rear brake light and turn singles dont work but parking lights work,fuse is ok brake switch is ok and front turn singles work as well as hazerds for the front only work and...


bad turn signal switch broken inside switch, need to remove steering wheel, remove clip, unplug connector under dash on column, undo the 3 screws hold switch in, install in reverse order.

Feb 11, 2010 | 1985 Chevrolet Chevy

3 Answers

My car is stuck in park, the brake lights do not work, Ive replaced the switch on the brake pedal and the turn signal switch. Its a 1995 Ford Taurus GL with a 3.0L. I can get the car out of park by turning...


The neutral safety switch on the tranny is going out. Replace this switch and you should not have any more problems. This switch registers that your foot is on the brake before it will allow it to come out of park to keep kids from accidently engaging the shifter.

Oct 04, 2009 | 2000 Lincoln LS

1 Answer

Passanger side brake light issue


Yes! It is a faulty turn signal assembly. You can try actuating the hazards several times, to try cleaning the contacts but if there is no change then replace it. In case you want to know, the wires from the brake switch, go up into the turn-signal assembly then out to the tail-lights. To fix it, disconnect the battery, you will need some tools. A steering wheel puller, a steering shaft compression tool, 1/2" drive ratchet, metric sockets, cir-clip pliers, a couple of small picks, #2 philips head screwdriver, and some torque-head screwdrivers. carefully pull off the horn cover( may have a couple of scews holding it from the other side), unplug the horn wire (push and twist), remove the cir-clip, remove the nut, mark the area where the steering wheel and shaft meet (use white-out), press off the steering wheel, Compess the shaft, remove the retaining clip(with the picks), remove horn spinner base, remove turn-signal assembly. I need to step back alittle bit, the plug, to the turn-signal, is half-way down the steering column, to unplug it you need to remove the lower dash panel, the bolts holding the column up inplace. The plug is in clear sight but the wiring harness is inside a plastic sheath, you'll see what I'm talking about.

Jun 17, 2009 | 1995 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1995 Mazda B-Series Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...