Question about 2001 Chevrolet Corvette

Open Question

GETTING ABS CODE C1214 SOLENOID VALVE RELAY CONTACT OR COIL CIRCUIT OPEN. WHERE IS THIS RELAY LOCATED, ALSO HOW DO YOU REMOVE A RELAY OUT OF THE FUSE BOX. THANKS,ED ABS AND TRACTION LIGHT ON IN DASH 2001 CORVETTE

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6 Answers

SOURCE: 2004 Monte Carlo

The traction control and abs are both activated by the abs sensors located at all four wheels. It is common for those sensors to get covered in brake dust and get false or no signal. Also the wiring connections can become corroded over time. I am not sure what the codes are for but checking the sensors/wiring are where I would start.

Posted on Apr 23, 2010

Ad
  • 2 Answers

SOURCE: 2003 Chevy Impala Service Traction Sytem show on Dash

I can't answer the question about the gas fumes, but I had the same problem last year with the "Service Traction Sysytem" message and the Trac and ABS lights coming on in my Impala. Mine turned out to be because of a bad wheel bearing, that was causing the ABS and traction system not to work. I'm not sure if you've experienced this, but another thing that would happen with mine was that I would go to brake and have a hard time depressing the brake pedal, almost like it was pushing back. That is the point when the Trac and ABS lights came on.

Posted on Jan 22, 2009

  • 1 Answer

SOURCE: Service Active Handling, ABS and Traction Control Lights on

I have had exactly the same problem on and off for 3 years now - and just solved it last week thanks to another computer site. Remove and disassemble both grounds from the top of both the left and right frame rails adjacent to the front corners of the engine block. Completely clean the green corrosion from the internal parts with fine sandpaper and add dielectric grease then re-assemble. Clean the mounting bolt and frame hole while you're at it. Sounds time consuming and difficult, but it ain't. No more than 45 minutes combined. I am a technical airhead so if I can do it so can you. What clued me in was the problem always occurred around wet or humid weather. Also, the clock would always lose time overnite. That has ceased also. Good luck. Anyone know why my left headlite, when deployed, vibrates and shimmys??? Sully ptsully@roadrunner.com

Posted on Jul 07, 2009

  • 1 Answer

SOURCE: trying to locate fuel pump relay for 1991 corvette- coupe

The fuel pump relay in the 1991 corvette is located under the IP on the pass side.
Open pass door, unscrew two screws under the glovebox (you will be upside down in the car), take off the fuse panel, unscrew third screw to plastic plate underneath glovebox, pull away carpet (velcro), pull down plastic plate (watch out for the wiring to the lamp), then under the glovebox you will find a number of fuses and relays if you dive in under there DEEP, prob 4 or 5 in a row, not really sure wich one, but one in the middle is the fuel relay, and they are the same (interchangable).
Take a look at --the12volt.com/relays/relays.asp--
It´s those relays we are talking about.

Posted on Sep 12, 2009

  • 39 Answers

SOURCE: my 2000 siverado shows abs code C0265 brake

The electronic brake control module will need to be replaced. The realy is inside the module and there is no replacement or repair for the module itself.

Posted on Mar 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 chevy silverado check engine light code CO201


ABS code not check engine light code .
DTC C0201 00: Antilock Brake System (ABS) Enable Relay Contact Circuit
The solenoid relay, located within the electronic brake control module (EBCM), supplies battery voltage to all of the valve solenoids.
Circuit/System Verification
With scan tool installed, clear the DTCs then drive the vehicle in a straight line at a speed greater than 20 km/h (13 mph). If the DTC did not set as a current DTC see diagnostic aids.
Circuit/System Testing
Test for an open or a short to ground in the battery positive voltage circuit to the EBCM. Verify no open or a short to ground is found.
Test the EBCM ground circuit, an open or high resistance.
? If an open or a short to ground is found, repair the circuit.
Replace the EBCM assembly.

DTC C0201 (Equal to or over 8600 GVW)
The system relay, located within the electronic brake control module (EBCM), supplies battery voltage to all of the valve solenoids and to the Antilock Brake System (ABS) pump motor. When the relay contacts close, the EBCM monitors the voltage supplied to the valve solenoids and compares this voltage to monitored ignition voltage.
Action Taken When the DTC Sets
• The EBCM disables the ABS/DRP.
• The ABS indicator turns ON.
• The brake warning indicator turns ON

Aug 08, 2017 | Cars & Trucks

2 Answers

What is ford OB1 fault code C1214?


Pedal Position Sensor B Circuit Intermittent

Aug 03, 2017 | Ford Cars & Trucks

1 Answer

1995 Ford F-350 OB1 fault codes C1226 &C1214 definition?


C1226, brake lamp indicator short circuit.

C1214, ABS inlet valve coil failure

Aug 03, 2017 | Ford F-350 Cars & Trucks

1 Answer

What are the probable causes of DTCs C1214 and C1233?


C1214: Brake Control Relay Contact Circuit Open
C1233: Right Front Wheel Speed Sensor Circuit Is Open or Shorted


From here, it looks like you have some bad connections or your DTC is in the process of dying.

May 25, 2015 | 2002 Oldsmobile Alero

1 Answer

Nissan code p1136 p1124


P1136 NISSAN - Intake Valve Timing Control Solenoid Valve Circuit Bank 2

Possible causes- Intake valve timing control solenoid valve bank 2 circuit is open or shorted.
- Intake valve timing control solenoid valve bank 2 circuit connectors
- Intake valve timing control solenoid valve bank 2
P1124 NISSAN - Throttle Control Motor Relay Circuit Short

Possible causes- Throttle Control Motor relay harness is open or shorted
- Throttle Control Motor relay circuit poor electrical connection
- Fualty Throttle Control Motor relay

Aug 29, 2012 | 2005 Nissan Quest

1 Answer

Secondary air ignition malfuction


This code can set for more than the pump not running. It could be a sensor issue that reads it, too high of pressure, just to name a few.

Circuit/System Verification
Verify that DTC P0412, P0418, P2430-P2433, P2440, or P2444 are not set.
* If any of the DTCs are set, perform those diagnostics first.
Ignition ON, command the AIR Pump Relay ON and OFF with a scan tool. The AIR pump should turn ON and OFF.
* If the AIR pump does not turn ON or OFF, refer to Secondary Air Injection Pump Malfunction
Command the AIR Solenoid ON and OFF with a scan tool. The AIR solenoid valve should click with each command.
* If the AIR solenoid valve does operate as specified, refer to Secondary Air Injection Solenoid Valve Malfunction.
Engine running, command the AIR Pump Relay ON with a scan tool while observing the AIR Pressure Sensor parameter. The reading should be 15-20 kPa above the BARO reading.
* If less than the specified range, refer to Secondary Air Injection System Pressure Low.
* If greater than the specified range, refer to Secondary Air Injection System Pressure High.
Engine running, command the AIR System ON while observing the AIR Pressure Sensor parameter. The reading should be 7-10 kPa above BARO.
* If less than the specified range, refer to Secondary Air Injection System Pressure Low.
* If greater than the specified range, refer to Secondary Air Injection System Pressure High.
Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing
Secondary Air Injection Pump Malfunction

Ignition OFF, disconnect the AIR pump relay.
Ignition ON, verify that a test lamp does not illuminate between the controlled output circuit terminal 87 and ground.
* If the test lamp illuminates, test the controlled output circuit for a short to voltage.
Verify that a test lamp illuminates between the AIR pump relay coil ignition circuit terminal 85 and ground.
* If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal and the ignition circuit fuse is open, replace the AIR pump relay and/or the AIR solenoid relay.
Verify that a test lamp illuminates between the AIR pump relay switch B+ circuit terminal 30 and ground.
* If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal and the B+ circuit fuse is open, test the controlled output circuit for a short to ground.
Ignition OFF, disconnect the harness connector at the AIR pump.
Test for less than 2 ohms between the AIR pump ground circuit terminal B and ground.
* If greater than the specified range, test the ground circuit for an open/high resistance.
Connect the harness connector at the AIR pump.
Connect the J 36169-HD with a 60A fuse between the AIR pump relay switch B+ circuit terminal 30 and the controlled output circuit terminal 87. Verify the AIR pump is activated.
* If the AIR pump does not activate, test the controlled output circuit for an open/high resistance. If the circuit tests normal, test or replace the AIR pump.
Remove the J 36169-HD jumper wire.
Connect a test lamp between the AIR pump relay coil ignition circuit terminal 85 and the AIR pump relay control circuit terminal 86.
Ignition ON, command the AIR Pump Relay ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
* If the test lamp is always ON, test the AIR pump relay control circuit for a short to ground. If the circuit tests normal, replace the ECM.
* If the test lamp is always OFF, test the AIR pump relay control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.
If all circuits test normal, replace the AIR pump relay.

Secondary Air Injection Solenoid Malfunction
Ignition OFF, disconnect the AIR solenoid relay.
Ignition ON, verify that a test lamp does not illuminate between the controlled output circuit terminal 87 and ground.
* If the test lamp illuminates, test the controlled output circuit for a short to voltage.
Verify that a test lamp illuminates between the AIR solenoid relay coil ignition circuit terminal 86 and ground.
* If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal and the ignition circuit fuse is open, replace the AIR solenoid relay and/or the AIR pump relay.
Verify that a test lamp illuminates between the AIR solenoid relay switch B+ circuit terminal 30 and ground.
* If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal and the B+ circuit fuse is open, test the controlled output circuit for a short to ground.
Ignition OFF, disconnect the harness connector at the AIR solenoid.
Test for less than 2 ohms between the AIR solenoid valve ground circuit terminal 4 and ground.
* If greater than the specified range, test the ground circuit for an open/high resistance.
Connect the harness connector at the secondary AIR solenoid.
Connect a 15A fused jumper wire between the AIR solenoid relay switch B+ circuit terminal 30 and the controlled output circuit terminal 87. Verify the AIR solenoid valve is activated.
* If the AIR solenoid valve does not activate, test the controlled output circuit for an open/high resistance. If the circuit tests normal, test or replace the AIR solenoid.
Remove the 15A fused jumper wire.
Connect a test lamp between the AIR solenoid relay coil ignition circuit terminal 86 and the relay coil control circuit terminal 85.
Ignition ON, command the AIR Solenoid ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
* If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the ECM.
* If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.
If all circuits test normal, replace the AIR solenoid relay.

Secondary Air Injection System Pressure Low
Engine running, inspect for exhaust leaks between the AIR solenoid valve and the catalytic converter.
* If an exhaust leak is detected, repair as necessary.
Ignition OFF, disconnect the AIR pump relay.
Engine running, connect the J 36169-HD with a 60A fuse between the AIR pump relay switch B+ circuit terminal 30 and the controlled output circuit terminal 87. Verify the AIR Pressure Sensor parameter is not 15-20 kPa above BARO.
* If 15-20 kPa above BARO, replace the AIR pump relay.
Ignition OFF, remove the J 36169-HD jumper wire and connect the AIR pump relay.
Remove the air inlet hose at the AIR pump.
Engine running, command the AIR System ON while observing the AIR Pressure Sensor parameter. Verify the reading is not 7-10 kPa above BARO.
* If 7-10 kPa above BARO, the AIR pump inlet hose/pipe assembly is restricted. Remove the restriction or replace the hose/pipe assembly.
Ignition OFF, disconnect the hose at the AIR pump outlet.
Disconnect the hose at the AIR solenoid valve inlet.
Install a length of standard 1 inch I.D. (25.4 mm) hose from the AIR pump outlet to the AIR solenoid valve inlet.
Engine running, command the AIR System ON while observing the AIR Pressure Sensor parameter. Verify the reading is not 7-10 kPa above BARO.
* If 7-10 kPa above BARO, test/inspect AIR pump outlet hoses/pipes for leaks or restrictions.
Test all AIR pump wiring and connections for less than 2 ohms. If the wiring and connections test normal and the hoses/pipes are OK, replace the AIR pump.

Secondary Air Injection System Pressure High
Ignition OFF, remove the AIR solenoid valve.
Connect the AIR pump outlet pipe/hose at the AIR solenoid valve.
Connect the AIR solenoid valve harness at the AIR solenoid valve.
Engine running, command the AIR system ON while observing the AIR Pressure Sensor parameter. The reading should be less than 11 kPa above BARO.
* If greater than the specified value, replace the AIR solenoid valve.
Inspect the AIR solenoid valve gaskets for proper alignment. If normal, test/inspect the AIR solenoid valve outlet pipe, exhaust manifold, and cylinder head for a restriction.

This issue and its repair may be under GM warranty. I think it would be worth your time to check at the dealer.

Hope helps.

Jan 06, 2012 | 2004 Buick Rainier

1 Answer

Code 10 on abs system


A circuit fault could have several possible causes:
-Open/short in wiring
-Blown 20A fuse
-Bad solenoid valve relay
-Bad ABS actuator
-Bad ABS control unit

Remember, if the fuse is blown, there could be a reason, so simply replacing it may not fix the actual problem. It can blow again and again...goof.gif

Oct 01, 2009 | 1995 Dodge Dakota

1 Answer

DTC trouble code 28 TCS C 1214 HC


The C1214 error is related to the electronic brake traction control module (EBTCM) BPMV pump motor relay contact circuit open. Check the 40A ABS Maxifuse in the underhood electrical center. if blown change it, clear the DTC and if it blows again check for a short in the 1642 line or internal short in the BPMV.
When an ABS/TCS operation is required, the EBTCM activates the pump motor relay and battery power is provided to the pump motor. DTC errors are either H (history) or C (current) I usually clear the history and see if it sets again later.
sebring1962@yahoo.com

May 14, 2009 | 2001 Chevrolet Corvette

Not finding what you are looking for?
2001 Chevrolet Corvette Logo

Related Topics:

1,607 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...