Question about Buick LeSabre

Open Question

Where is the coolant temperature sensor located on a 92 lesabre?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 99 cadillac de ville

the coolant temp sensor is at the rear of the engine and is a "bad word" to get to. the 3 relays are at the bottom,under the fans. if you remove the driver side fan out of the way( 2 10mm bolts holding the fan) you should have good access to them. they do have locks on them and may be tricky to unplug. there is a 7/16 nut holding the relay plate down. remove and it should be easy to remove them.

Posted on Jul 09, 2008

Ad
  • 15 Answers

SOURCE: Coolant temp sensor

it is located where the upper radiator hose enters the thermostat housing

Posted on Jan 27, 2009

  • 155 Answers

SOURCE: How do I change the temperature sensor under the

It’s located on the driver’s side of the engine on top /side of the head.. midway.. I don’t think you need to remove the engine cover to see it.. if it is the correct one it will have a dark green top.. the bad version has a black top… but they can all go out to lunch on you if old enough.

To replace.. make sure the car is cool..
You need a hood tool.. or small pair of pliers to remove the retaining clip that holds it in place.
Place a rag under and around it to catch the coolant.. you will lose less than a half a cup.. if that.

Pull the retaining clip back toward you.. try not to drop it.. (another good reason for the rag)

Wiggle the sensor.. pop it out.. and replace with the new green top one make sure you clean the area well.. and when you reinstall the new one that the c clip goes back on straight or it will leak.

Once you see the part out of the box.. you will understand how it works

Start the car.. check for leaks.. run until warm with the heater on.. top up the coolant overflow bottle with distilled water.. (if more than a half a cup.. you should mix the proper anti freeze and distilled water and then top up with that)

Good luck

Posted on May 06, 2009

  • 119 Answers

SOURCE: replacement of coolant temperature sensor

located under intake in water crossover pipe,you can access the sensor by removing intake chamber box,then pcv hose connected to the block,the connector is orangeish 2pin,use a 19mmdeep socket on a 3/8 ratchet to get it loose,make sure engine is cool,also make sure there is a new brass washer with your new sensor,sometimes the old washer comes off when removing the sensor,sometimes it sticks to the pipe,some coolant will escape so make sure to top it off

Posted on Jul 14, 2009

  • 521 Answers

SOURCE: Coolant Temperature Sensor location on 2006 impala

driver side of the engine block, forward and above the transmission. This piece threads into the engine block.

Posted on Jul 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the heat sending unit located in my 98 buick lesabre


engine coolant temperature sensor located on intake manifold under the thermostat housing.

Dec 25, 2012 | Cars & Trucks

1 Answer

Po128 po131 po300 po463


P0128 Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)
P0131 O2 Sensor Circuit Low Voltage (Bank 1 Sensor 1)
P0300 Random/Multiple Cylinder Misfire Detected
P0463 Fuel Level Sensor Circuit High input

obd2 code scanner

Aug 16, 2012 | 2000 Buick LeSabre

1 Answer

Where is the tempurture cooling sensor located on a 1994 buick regal


The coolant temperature sensor is a thermistor mounted in the engine coolant stream. A thermistor is an electrical device that varies its resistance in relation to changes in temperature.

For 2.5L engines, the coolant temperature sensor is located on the left side of the cylinder head.

For MFI engines, the coolant temperature sensor is located on the intake manifold water jacket or near (or on) the thermostat housing.

zjlimited_2011.jpg

Fig. 1: Engine Coolant Temperature (ECT) sensor and connector


zjlimited_772.gif

Fig.: Engine Coolant Temperature (ECT) sensor location-3.1L (VIN T) engine shown

Hope this helps (remember to rating this and leave an testimonial comment about this free answer).

Oct 10, 2011 | 1994 Buick Regal Gran Sport

1 Answer

2000 le sabre runs hot but when I put air on it cools down


SOUND LIKE FAULTY OPEN ENGINE COOLANT TEMPERATURE SENSOR. HAVE CAR HOOK TO CODE SCANNER WHERE YOU CAN SEE ENGINE COOLANT TEMPERATURE. IF ENGINE HOT AND CODE SCANNER SHOW LOWER TEMPERATURE LIKE 100 - 80 DEGREES ECT IS BAD.

Jun 14, 2011 | 2000 Buick LeSabre

1 Answer

The check enging light comes on then goes off. I foud out the code po118 engine coolant temp circut high input. is it the coolant temp sensor. if so how do I replace it. It is on a 2004 jetta tdi


According to Autozone.com:

Because ECT (engine coolant temperature) sensor procedures vary depending upon their location, first locate the part. You may need to partially drain the engine coolant to prevent coolant spillage.
  • Disconnect the negative battery cable.
  • Unplug the ECT.
  • Then, unscrew it.
  • Reverse the removal procedures to install the new part.
  • Connect the negative battery cable to the battery.



    Related Parts:
---
Coolant Temperature Sensor printpage_icon.gif



0900c152801bfc38.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Remove the coolant temperature sensor
The coolant temperature gauge sensor is a temperature-variable resistor, or thermistor. As coolant temperature increases, the resistance of the sensor decreases or decreases, depending on the type of sensor.
A1 and A2 platforms use a different type of circuit that A3 vehicles. On A1 and A2 vehicles, the circuit is a "resistance to ground" type. A3 vehicles use a "variable voltage" type, where a voltage is supplied to the sensor. Because of the circuitry design on A3 vehicles, testing of the coolant temperature gauge is limited.
The engine coolant temperature gauge uses a heat sensitive sending unit to transmit an electrical signal to the gauge. The sending unit is a heat sensitive variable resistor that is located on or near to the cylinder head and threads into an engine coolant passage. The sensors are a Negative Temperature Coefficient (NTC) type. As the temperature increases, the electrical resistance of the sensor decreases. As the coolant temperature changes, so does the resistance of the sensor. The gauge is calibrated within the operating range of the sensor and interprets the resistance value to display the coolant temperature.
Beginning with model year 1994, the engine coolant gauge and the Engine Control Module (ECM) temperature sensors were combined into one sensor with 4 terminals. The basic operation remains the same in that their resistance decreases as the coolant temperature increases, however the actual resistance values of the 2 sensor circuits are different. The electrical connector of the 4-wire terminal sensor ( 1 and 2 ) is keyed to prevent improper connection of the sensor's electrical circuit.

0900c152801bfc39.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Beginning with model year 1994, the Engine Coolant Temperature Sensors combined the sensors for the ECM and the gauge into one sensor-1997 2.8L V6 sensor shown


0900c152801bfc3a.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. The electrical connector for the combined temperature sensors is keyed to avoid improperly connecting the sensor's wiring-1997 2.8L V6 connector shown

Oct 17, 2010 | 2004 Volkswagen Jetta

1 Answer

Trouble locating cooling sensor on 2003 gmc envoy


4.2L Engine To Remove:
  1. Disconnect the negative battery cable from the battery.
  2. Drain the coolant from the engine.
  3. Disconnect the engine coolant temperature (ECT) sensor connector. Engine coolant temperature sensor removal and installation gm-04-42-1509.gif

  4. Remove the engine coolant temperature (ECT) sensor from the engine.
To Install:
  1. Apply thread sealer P/N 12346004 or equivalent to the engine coolant temperature (ECT) sensor threads.
  2. Install the engine coolant temperature (ECT) sensor into the engine. Torque the sensor to 12 ft-lb (16 Nm).
  3. Connect the engine coolant temperature (ECT) sensor connector.
  4. Refill the engine with coolant.
  5. Connect the negative battery cable to the battery.
5.3L & 6.0L Engines To Remove:
  1. Drain the coolant from the engine.
  2. Disconnect the engine coolant temperature (ECT) sensor connector. Engine coolant temperature sensor removal and installation removeect.gif

  3. Remove the engine coolant temperature (ECT) sensor from the left cylinder head.
To Install:
  1. Apply thread sealer P/N 12346004 or equivalent to the engine coolant temperature (ECT) sensor threads.
  2. Install the engine coolant temperature (ECT) sensor into the left cylinder head. Torque the sensor to 15 ft-lb (20 Nm).
  3. Connect the engine coolant temperature (ECT) sensor connector.
  4. Refill the engine with coolant.

Jul 08, 2010 | 2003 GMC Envoy

1 Answer

2000 Buick LeSabre No heat, blows cold air.


check to see if both hoses are hot going to your heater core if they are then core is fine.That would point to your temperature sensor.

Feb 07, 2010 | 2000 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...