Question about 2005 Nissan Frontier

Open Question

I have a nissan frontier 2006 and I scan computer and he get me the error p0345, cam sensor. I need know where is this sensor for change

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nissan Almera wont start with code P0345


Code 345 means the cam sensor on bank two is not sending the correct signal to the engine computer. So no spark.
If you have replaced the sensor, the problem could be the cam or the wiring from the sensor to the computer.

Dec 03, 2014 | 2005 Nissan Almera 1.5

1 Answer

How do you reset the service engine light in a 2006 nissan frontier


You must first diagnose and repair the malfunction that has caused your service engine light to come on in the first place (otherwise the light will just come back on again). Then you must use a scan tool to clear the computer memory.

Dec 22, 2011 | 2006 Nissan Frontier

1 Answer

2006 frontier camshaft position sensor


If you do not know where the Camshaft Position Sensor is located, then it would be safe to assume that you have not properly tested the sensor or the circuits that operate the sensor. Therefore, you cannot possibly know for sure that it even NEEDS to be replaced...so why are you looking to replace it?

Nov 20, 2011 | 2006 Nissan Frontier

1 Answer

2006 nissan frontier ceck engine light on p2a00 circui range/performance bank 1 sensor 1


change your 02 sensor, bank 1 sensor 1 willl be a sensor screwed into a bung attached to the exaust before the catalyst. driver side

Nov 15, 2011 | 2006 Nissan Frontier

1 Answer

My 2003 Nissan Frontier stalled and will not crank up when I. Scanned it the P0325 and P0340 codes appeared. How do I fix this?


I would say that the P0340 is causing your no start problem.....This is a cam sensor code......The cam sensor is in the distributor and is not servicable.....I would recommend taking it to a repair shop to properly diagnose the problem before replacing the distributor.

Mar 17, 2011 | 2003 Nissan Frontier Crew Cab

1 Answer

After changing a clutch in 06 nissan frontier i now have a spin no start . any suggestions? ps. already replaced crank pos sensor


was flywheel replaced? i've had this happen on one turned out sensor ring distorted on flywheel.went through three until i got a straight one.how did bx look it came in?watch intake cam timing pid while cranking.....should be very close to zero degrees.if not suspect sensor ring damage.l

Jan 19, 2011 | 2006 Nissan Frontier

1 Answer

Locatio camshaft sensor 05 frontier 4.0 v6


on the back of the cylinder head. hard to see, but there is a connector with green slide piece inside of it. that is the location of cam sensors.

Sep 21, 2010 | 2006 Nissan Frontier

1 Answer

I need to change both oxigen sensors on my Nissan Frontier 2006. Where are they located?


What makes you think they need replacement? they are in the exhaust pipe. V6? 4 cylinder?

May 10, 2010 | 2006 Nissan Frontier

Not finding what you are looking for?
2005 Nissan Frontier Logo

1,220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

723 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...