Question about 1983 Ford Crown Victoria

1 Answer

My sons 83 crown vic is not getting gas. It gets gas where the gas line hooks into the throttle body, but for some reason nothing is coming out of the injectors. Was working fine one day and the next nothing.what could be some possible causes that I should be looking at?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,019 Answers

The throttle body is basically a single large injector, and it could have burned out its solenoid. It is controlled by a brainbox that uses the distributor input, temp sensor input, throttle position input, etc., so there are many possible problems.
The best way is to let someone put it on a diagnostic machine unfortunately.

Posted on May 23, 2011

  • fearofscott May 25, 2011

    Yeah I figured it was going to be something electronic

  • fearofscott May 25, 2011

    But thank you for your help.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I drove my 85 ltd crown vic to work fine. After a long day of work she wouldn't crank just turn over. I have changed the distributive module and cap and the rotor button. The timing was reset also


is it getting gass if u got spark to the plug's it should start.dump alittle gas down carb or throttle body making sure to replace air cleaner or snorkle and try and start.if starts could be fuel pump.

Mar 03, 2013 | 1985 Ford Crown Victoria

2 Answers

Stalling crown vic


Dependent on what year you have. If it has an idle speed motor that could be cleaned as well as the throttle body. Idle speed motor may need to be replaced sometimes a good cleaning hooks them right up.

Feb 22, 2013 | 1985 Ford Crown Victoria

1 Answer

84 crown vic wont start


IF THE PROBLEM IS NOT THE FUEL PUMP, FUEL RELAY, FUEL PRESSURE, AND OR FUSE WAT ELSE COULD B THE PROBLEM

Dec 03, 2011 | 1984 Ford Crown Victoria

1 Answer

When i start my vic, it will start right up but immediately die as if it doesnt know how to idle. If i lightly push the gas or hold the throttle open it sounds and runs fine. If i let off of the throttle...


This could be a Vacuum line broke or not installed. I changed fuel injectors on mine and forgot to install one vacuum hose on the Rubber intake near the throttle body, with the same exact symptoms. If you have done any work recently just double check that all the lines and hoses are attached in their correct positions. If you have not done any work recently to is, it may be possible for a hose to break and become detached and not allow it to idle. This is my only experience with these symptoms, hope it helps

Aug 06, 2011 | 2000 Ford Crown Victoria

1 Answer

1988 crown vic fuel injector harness both contacts lite up


sounds like your PCM might be bad if it is not supplying correct voltage to fuel injector.

Also, the fuel injector itself may be bad or bad ground.

Does it have throttle body injection on that crown vic?

Jul 10, 2010 | 1988 Ford Crown Victoria

1 Answer

My egr vaulv i dnt knw how to change it on my crown vic


It unbolts from the throttle body and the pipe is screwed into it. But are you sure you need one. They rarely go bad. Usually if you have a check engine light on for the egr valve it is because of a bad DPFE sensor or a plugged passage in the throttle body.

Apr 22, 2010 | 1997 Ford Crown Victoria

1 Answer

Cant loc the idle air control vavlve located on a 1988 crown vic


attached to the throttle body,looks like an electric motor bolted to a square piece with the corners notched out,with 2 wire connector on the end.

Feb 19, 2010 | 1988 Ford Crown Victoria

2 Answers

Tune up and clean the throttle plate


Ford is notorius for bad breathing.There EGR system is terrible, it always causes a lot of carbon build up in the throttle plates. The best thing to do, is to take of the throttle body assembly and digg out the carbon thats restricting the air flow. Also, it is a good rule or thumb to clean the throttle plate with carb & throttle cleaner with a tooth brush. Add a bottle of fuel injector cleaner to a full tank of gas. While your doing all this you might as well change the EGR valve. If you follow the air intake pipe from the air filter box, it should lead you to the throttle body assembly. The EGR valve is located on the passenger side by the fire wall underneath the heater hoses and AC lines. Good luck, Ford engineers must have been drinking when they designed their vehicles, they don't make anything easy.

Mar 31, 2009 | 1991 Ford LTD Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...