Question about Mitsubishi Minivan

1 Answer

How do I get access to the spark plugs for removal. Please help.

Posted by on

  • david searle May 23, 2011

    what model or engine are you inquiring about?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

You'll need to loosen the srews on the gasket on top of the engine and then remove them...

Posted on May 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant find plugs on a 3.7 6 cylinder 2 wheel drive dakota please help


3.7L Engines
Each individual spark plug is located under each ignition coil. Each individual ignition coil must be removed to gain access to each spark plug. Refer to Ignition Coil Removal/Installation. Prior to removing spark plug, spray compressed air around base of ignition coil at cylinder head. This will help prevent foreign material from entering combustion chamber.

  1. Remove spark plug from cylinder head using a quality socket with a rubber or foam insert.
  2. Inspect spark plug condition.
To install:
  1. Start the spark plug into the cylinder head by hand to avoid cross threading.
  2. Before installing coil(s), check condition of coil o-ring and replace as necessary. To aid in coil installation, apply silicone to coil o-ring.
  3. Tighten spark plugs to 27 Nm (20 ft. lbs.) torque.
  4. Install ignition coil(s). Refer to Ignition Coil Removal/Installation.

Sep 21, 2013 | Cars & Trucks

1 Answer

I need help changing spark plugs in my 2004 ford Taurus It seems I have to remove the intak assembly to access the rear plugs. what do I do to remove the intake safely and properly replace everything?


Hello,

You will have to remove the intake assembly to be able to remove the spark plug. You can also go about it from the ignition coil. To replace the spark plug, please follow the steps below to do so. You will be needing these instruments: Phillips screwdriver, Socket wrench, Spark plug socket, Anti-seize compound, Dielectric compound, Small screwdriver, then follow the steps:
  1. Disconnect the car's negative battery cable at a time when the engine is cool.
  2. Unscrew the individual ignition coil using a screwdriver and then remove the coil and set it aside.
  3. Pull out the spark plug wire at the plug end, grasping it by the boot and twisting it out; a special tool for this is available. Disconnect the same wire at the ignition coil.
  4. Clean out the spark plug's hole, using compressed air to blow out all dust, dirt and debris from inside.
  5. Remove the spark plug from the engine using a socket wrench with a spark plug socket; turn the plug counterclockwise to remove it.
  6. Apply a thin coat of anti-seize compound to the threads of the replacement spark plug. Make sure you get no compound on the plug's electrodes.
  7. Thread the spark plug into its hole, making sure you don't cross-thread it, and then tighten it with the wrench and spark plug socket.
  8. Coat the insides of the spark plug boots with dielectric compound; use a small screwdriver to apply the compound.
  9. Install the ignition coil and screw it into place.
  10. Repeat the above steps for each spark plug/wire that needs changing and installation.
  11. Reconnect the negative battery cable once you've installed all necessary plus and wires
Hope this helped. Thank You for using FixYa!!!

Jan 15, 2011 | 2004 Ford Taurus

2 Answers

Where are the spark plugs on this car please help me


SPARK PLUGS FOR 2.4L ENGINE IS ON TOP IN CYLINDER UNDER IGNITION COIL COVER.REMOVE 4 BOLTS TO REMOVE ENGINE TOP COVER. NOW IF YOU HAVE 3.1L OR 3.4L ENGINE SPARK PLUGS IN BOTH CYLINDER HEADS.

Oct 08, 2010 | 1998 Chevrolet Malibu

1 Answer

Cant find the spark plugs


Here's a link that will help you. I've included the info that you need to locate the plugs below. Good luck!

http://www.ehow.com/how_4484637_replace-spark-plugs-oldsmobile-alero.html

To gain access to the spark plugs and spark plug wires do the following. In a 2.4 liter engine, remove the ignition coil and module assembly from the top of the engine to gain access. In this Alero model's engine, the spark plugs run down the center of the engine. In a 3.1 liter engine, remove the air cleaner to gain access. The spark plugs are located next to the engine oil reservoir. For a 3.4 liter engine, remove the windshield wiper module cover and rotate the engine for service access. For a 2.2 liter engine, the spark plug wires are located across the top of the engine and require no components to be removed for access to the spark plugs.

Mar 10, 2010 | 1999 Oldsmobile Alero

1 Answer

How do change spark plugs on a 1998 xj8


Remove plastic cover over the engine ( three screws).
You then have access to the front three spark plugs (cylinders 1,3,5) remove the nut which holds down the independant coils and remove the spark plugs, fit new spark plugs and fit coils on the three front cylinders.
Now it gets a little tricky, you will only be able to access number 2 back cylinder so you have to remove the induction manifold (12 bolts I think) to access the back three cylinders (2,3,6,) properly.
Then proceed as with the front three spark plugs, refit manifold and plastic cover,

Sep 29, 2009 | 1998 Jaguar XJ8L

1 Answer

Change sparks plugs on 06 hyundai sonata v6


You didn't specify whether you have the (4) cylinder or the (6) cylinder engine..... I have a 2004 Hyundai Sonata 2.4L 4 cylinder and I just changed the spark plugs in it. I believe that the 2005 2.4L engine is the same. To locate and change the (4) spark plugs on a 2004 Hyundai 2.4L 4 cylinder engine: Remove the (4) 12mm bolts from the decorative plastic engine cover. Remove plastic cover from engine and place it off to the side out of your way. Standing in front of the car, the (4) spark plugs are located laterally (left to right) in the recessed area underneath where the plastic engine cover was removed. Note: This engine has (2) coils....They are located above spark plugs number (2) and (3) from left to right. Starting with the fist spark plug on the left: Remove the spark plug cable by pulling straight up on the insulated connector. Using a spark plug socket, remove the old spark plug and install a new one in it's place. To access the second spark plug from the left, remove the electrical connector and the spark plug cable wire from coil number (1) and then remove the (2) 12mm bolts that secure the coil to the engine. Spark plug number (2) is located directly under the coil. Lift the coil straight up removing the insulated connector from spark plug number (2). Using a spark plug socket, remove old spark and install a new one in it's place. Repeat same procedures for spark plugs number (3) and (4). Note: If you have the (6) cylinder engine, the front (3) sparks pluge are readilly accessible but in order to access the (3) rear spark plugs, you will have to remove the intake manifold

Jul 08, 2009 | 2006 Hyundai Sonata

1 Answer

How do change my spark plugs for a 1994 gmc safari?


Hello dechile1313: My name is Roger and I can help you. You will need to remove the engine cover from the inside to gain access to some of the spark plugs. The other plugs are accessed better from the wheel Wells. Raise the front end up to drop the tires down. Reach through the wheel well and lift up the rain shield you will see the spark plugs. Be sure and twist the plug wire boots back and forth to keep from braking the t plug wire ends. Please rate the quality of this reply. This lets us know you received the information you requested. Thank You for using FixYa. Roger

May 06, 2009 | 1994 GMC Safari

1 Answer

Replacing Spark Plugs


Remove the engine cowling inside to access the ones in the rear. The front ones can be accessed from the front of the engine compartment. One or two of the middle row plugs can be accessed most easily by jacking up the vehicle and removing the front tires. Make sure you follow all safety procedures and use jack stands.

Mar 22, 2009 | 1995 Chevrolet G20

1 Answer

I can't find the spark plugs in my 2005 sonata


To locate and change the (4) spark plugs on a 2004 Hyundai 2.4L 4 cylinder engine:
Remove the (4) 12mm bolts from the decorative plastic engine cover. Remove plastic cover from engine and place it off to the side out of your way.
Standing in front of the car, the (4) spark plugs are located laterally (left to right) in the recessed area underneath where the plastic engine cover was removed.
Note: This engine has (2) coils....They are located above spark plugs number (2) and (3) from left to right.
Starting with the fist spark plug on the left: Remove the spark plug cable by pulling straight up on the insulated connector. Using a spark plug socket, remove the old spark plug and install a new one in it's place.
To access the second spark plug from the left, remove the electrical connector and the spark plug cable wire from coil number (1) and then remove the (2) 12mm bolts that secure the coil to the engine. Spark plug number (2) is located directly under the coil. Lift the coil straight up removing the insulated connector from spark plug number (2). Using a spark plug socket, remove old spark and install a new one in it's place.
Repeat same procedures for spark plugs number (3) and (4).
Note: If you have the (6) cylinder engine, the front (3) sparks pluge are readilly accessible but in order to access the (3) rear spark plugs, you will have to remove the intake manifold.


please rate!

Mar 18, 2009 | 2006 Hyundai Sonata

1 Answer

How to access spark plugs on a 1999 towncar


you need to remove the coil first and then the plug. Each plug has it's own coil.

  1. Disconnect the connector from the ignition coil.
  1. Remove the bolt from the ignition coil.
f5a077e.gif
  1. Remove the ignition coil on plug.
please rate as fixya if this helps. tahnks

Mar 03, 2009 | 1999 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...