Question about 2008 Chrysler Sebring Convertible

Open Question

How to remove the door panel on a 2008 Chrysler Sebring

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 82 Answers

SOURCE: driver side power window stopped working

The door panel is held on by plastic clips and 5 screws. 3 screws are on the bottom and 1 in the pull cup and 1 in the inner door handle.Then grab one of the corners and give a small tug, when you get some of the clips to pop out then proceed around the whole panel. To replace the panel take the clips out of the door with a fork and slide them back into the panel and then line it up on the door and use your hand like a hammer and bang the panel back on. Hope this helps

Posted on Jan 12, 2009

ga_drifter
  • 36 Answers

SOURCE: 2004 chrysler sebring.The driver side rear door electric window

you have a bad window regulator assembly

Posted on Jan 30, 2009

  • 1986 Answers

SOURCE: How to remove interior door panel on 2002 chrysler t & c???

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 1986 Answers

SOURCE: window off track driver side 1997 sebring

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 109 Answers

SOURCE: chrysler 2004 sebring manual

remove the hidden screws be hind mini covers, start from the bottom of panel with panel tool and pry the plastic retainers away from the door plate and remove the wire connectors form switches and replace the handle, reverse the order, GOOD LUCK, RDJRP

Posted on Aug 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does my 2008 Chrysler sebring have two thermostats


there is only one thermostat on your car. what you probably have is split temp control one to set temp for the passenger side and one for the drivers side. if so then the temp control door on the passenger side is probably not functioning properly. take it to a shop to have fixed.

Nov 30, 2014 | 2008 Chrysler Sebring

1 Answer

Remove door panel on 2008 Chrysler Sebring to replace window switch





This pic is of a door panel retainer that hold the panel onto the inner door frame. They are typically placed on the sides and bottom of the door panel. The top of the door panel slides downward into a channel on the top of the door frame.
The first step is to locate all screws on the door panel and remove them. Usually the screws are in the door handle to hold the handle in place. Look for other locations for screws. SOmetimes the screws have button covers that hide the screw head.
After all screws are out , take a wide blade screw driver or you can purchase a tool for door panel removal, and insert the screw driver inbetween the panel and the door, and pry these fasteners out all around the panel. Once the panel is free on the side and bottom, lift up on the panel to disengage it from the top channel. Be careful of the wiring behind the panel. You may have to unplug the wire connectors to remove the panel further.
These panel fasteners become brittle and may break when they are popped out. They are avaiable at auto parts stores. Just take one with you to match up, since there are several differnt sizes.

May 04, 2014 | 2008 Chrysler Sebring

1 Answer

How do i replace a 2008 chrysler sebring convertible drivers side mirror?


remve teh black plastic cover from the door then remove the door panal undo the conector if its power mirror remove 3 10mm nuts revers for instolaton

Feb 13, 2014 | 2008 Chrysler 300

1 Answer

Chrysler Sebring 2008 headlight assembly removal


some times headlamp units have a plastic retaining clip on the underside of headlamp, does the headlight move from side to side? try to pull the headlight back from the top of unit then lift up the headlamp unit, if not it could be the headlamp adjusters holding unit in place.

Dec 06, 2013 | 2008 Chrysler Sebring

1 Answer

Driver door not opening from inside and outside 2008 Chrysler Sebring


these doors have electrical releases ...go to autozone have them read it free ,,they will have your answer

Oct 23, 2013 | 2008 Chrysler Sebring

1 Answer

Remove door panel on 2002 sebring


you'll need some special tool as to not damage retainers for door panel,it's complicated to explain make sure you remove all screws ,some are hidden in door handle ,door release handle and under round circuler plugs ,take your time and be careful for wires and connectionc . can i ask YYYYYYYY WHATS WRONG ?

Sep 30, 2012 | 2002 Chrysler Sebring

2 Answers

How do I replace a power window switch on a 2008 sebring on drivers door


If the switch has been wet a few times the contacts may only need to be cleaned. If water is a common problem apply dielectic compound to the connections so you don't have the repeated problem.

Nov 28, 2009 | 2007 Chrysler Sebring Sedan

1 Answer

Access to front door speakers


on the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge.Then you can get to your speaker

Sep 13, 2009 | 1998 Chrysler Sebring

1 Answer

Chrysler 2004 sebring manual, how to remove driver door panel to repair broken inside door handle


remove the hidden screws be hind mini covers, start from the bottom of panel with panel tool and pry the plastic retainers away from the door plate and remove the wire connectors form switches and replace the handle, reverse the order, GOOD LUCK, RDJRP

Aug 16, 2009 | 2004 Chrysler Sebring

1 Answer

How do i remove the right rear door panel on a 04 Chrysler Sebring


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Apr 11, 2009 | 2004 Chrysler Sebring

Not finding what you are looking for?
2008 Chrysler Sebring Convertible Logo

Related Topics:

323 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...