Question about 2002 Ford Taurus

1 Answer

How do i get brake rotor off? do i need to take axle nut off?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,977 Answers

Once the caliper is off and the rotor won`t come off then you will have to hit the rotor with a hammer near the wheel studs to loosen it from rust.

Posted on May 22, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove front axle


first and foremost "brake" the lug nuts loose,then you are going to want lift the front of the vehicle using a quality jack and support the front of the vehicle with approved jack stands(don\'t forget to set the parking brake!) . remove front wheels,then if a impact gun is not available have a friend hold their foot on the brake .now using a braker bar and the proper socket "brake" the axle nut(in the center of the brake rotor) loose . now your home free- remove lower ball joint and tie rod end nuts and remove tie rod and ball joint from spindle( the parts with the brake rotor and caliper on it)by tapping rather hard on the side of them both with a ballpeen hammer(at this point they should just"pop" out of their sockets).now holding spindle by the brake rotor swing it outward while pushing "in" on the end of the threads for the axle . with the axle now out of the spindle with a small pry bar reach in between where the axle meets the transmission (be careful not to damage seal by using a flashlight to keep an eye on what your doing.now pry rather forcefully and the axle when"pop" out. make sure and have a shallow drin pan under the trans as when you take the axle out fluid will follow.reverse the procedure and don\'t forget to top-off the trans fluid.even if none came out during axle install it is always a great idea to check this fluid when doing axles as fluid is a lot cheaper than a trans.

Apr 03, 2014 | 2004 Chevrolet Monte Carlo

2 Answers

How remove the rotor to change bearing for 2005 chev colorado front


first you remove all the lug nuts and the wheel and tire. To get the rotor off you will need to remove the brake caliper. they are held in with 1/4" hex screws. If you don't have an allen wrench you can use a socket extension to removes these. Once unscrewed the calpet simply lifts off the rotor and the rotor is ready to come off. You will need to remove the axle nut and keeper then the rotor slides off towards you and the wheel bearings will come out with the rotor.

Sep 26, 2011 | 2005 Chevrolet Colorado

1 Answer

Need to change a front wheel bearing...is it hard to do myself?


moz-screenshot-2.png-Jack up the car
-remove the tire, 19mm socket
-remove the brake caliper, its either an 18mm or 15mm socket that will remove the bracket bolts.
-remove the rotor
-remove the axle nut, its either a 34 or 36 mm
-unplug ABS sensor connector if equipped
-remove the three bolts that hold the bearing/hub assembly to the knuckle, a 13mm socket will work
Remove the wheel bearing.

It is important to tighten the axle nut to the proper spec. Failure to do so will cause the new bearing to fail. you will need a 1/2" torque wrench for this.

To make removing and installing the axle nut easier place a punch in the fins of the rotor and rotate the rotor until the punch rests on the caliper (it doesn't hurt to put a couple lug nuts on to hold the caliper tight to the hub). This will hold the hub in place while you looses and tighten the axle nut.

29d321a.jpg
cba1266.jpgae46743.jpg

Nov 09, 2010 | Chevrolet Tahoe Cars & Trucks

1 Answer

How do you remove the rotors from a 1991 honda accord?


Loosen both front wheel lug nuts and raise car and support on jack stands. Remove wheels and have a friend hold brake pedal down and remove axle nut. Use a chisel or screwdriver to remove stake on nut to axle edge. I use a 3/4 drive set socket and remove axle nut. Rent it from Autozone. Remove caliper assy and support with coat hanger or bungee cord to hold weight of assy off of brake hose. Remove Cotter pin and nut on lower control arm. Separate with ball joint fork and pull strut assy away to the side while pulling stub axle through and out of the way. Remove 4 bolts holding rotor and hub assy. on the inside of steering knuckle and separate. Now remove 4 bolts on hub's outer side and separate rotor and hub. You can use a bar or large screwdriver between wheel studs to loosen the 4 bolts.

Aug 04, 2010 | 1991 Honda Accord

1 Answer

How do you remove the rotors on a 1995 ford bronco


The rotors on most vehicles are removed by (1) removing the wheel, (2) remove the silver colored cap in the center of the hub, (3) remove the cotter pin that goes through the axle nut and axle, (4) remove the axle nut, (5) remove the disc brake caliper (6) now pull on the rotor. It should slide off the axle. Reassemble in reverse order, being sure that the axle bearings are in place with proper amount of grease.

Oct 25, 2009 | 1995 Ford Bronco

1 Answer

Which direction to turn nut when removing brake rotors on 1998 Chevy Metro clockwise or counter


All brake parts are counter clockwise. But what nut are you talking about. Not the axle nut? That doesn't come off. Rotor pops off after caliper is removed.

Aug 18, 2009 | 1999 Chevrolet Metro

1 Answer

I belive that my axel is bent I need to replace it but I don't know how i am trying to find a blue print to show me step by step


lossen the large retainer nut that holds the axle through the brake rotor. than lossen up the lower ball joint nut, seperate the lower ball joint from the steering knuckle. slide out the strut enough to slip the axle out of the brake rotor. now with a large screw driver or pry bar placed between the axle and the trans axle, pop the old axle out. it's held in place with a c clip attached to the inner cv joint spline. reassemble in reverse order.
good luck chris

Mar 19, 2009 | 1998 Ford Escort

2 Answers

How to replace front wheel bearing on 2003 GMC ENVOY


Jack up vehicle and support with jack stands
Take off wheel
remove brake caliper
remove caliper bracket
remove rotor
remove axle retaining nut cotter pin
remove axle retaining nut
remove axle from output flange
pull axle out of vehicle
hub and bearing assembly held in by 4 bolts

installation is reverse of removal. You will need to find out the torque specs for the axle retaining nut.

Jan 14, 2009 | 2002 GMC Envoy

1 Answer

Brake rotor replacement on 2004 matrix


If you are talking about the brake rotors, you do NOT remove the 30 mm nut. That nut just holds the axle shaft to the hub. Remove the caliper and the caliper bracket, the rotor should come off, you may have to tap the brake rotor to dislodge it from the center hub.

Oct 05, 2008 | 2004 Toyota Matrix

Not finding what you are looking for?
2002 Ford Taurus Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...