Question about Ford Fiesta

Open Question

How do you remove the air bag from the steering wheel on a Ford Fiesta 1.4L Petrol Zetec 2003 model.?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 119 Answers

SOURCE: 2000 jetta need to remove steering wheel

This is not an easy procedure, especially since you've never done it before. With the wheels in the straight ahead position, look at the back of the steering wheel, you'll see two holes. One at 9 o'clock and one at 3 o'clock. You stick a small flat blade screwdriver in the first hole and you pry on the retaining spring while gently pulling on the airbag until it releases. Repeat on the other side. I'm a professional mechanic and the first time I did it, it took me over a half hour to figure it out. Now I can do it in less than a minute. Might want to take it to the dealer.

Posted on May 21, 2008

MrScary66613
  • 1990 Answers

SOURCE: fitting a fan belt

There should be a Belt Routing Diagram Under the Hood Somewhere and In the Back of the Owners Manual.

Posted on Jan 03, 2009

  • 104 Answers

SOURCE: Remove me Steering wheel bmw 1999 e46 3 series

Disconnect negative battery cable. Locate airbag retentions on back of steering wheel. Unbolt or unclip retention devices, and release airbag. Then: Unplug airbag electrical connector. Remove nut or bolt in center of steering wheel with pneumatic impact wrench if necessary . Using appropriate steering wheel removal tool kit, carefully remove steering wheel, paying attention to associated wires, etc. Unplug anything not accompanying wheel, or that is in the way. Pay close attention to any rods, or contact pieces associated with the horn button(s.) Replace these upon reinstall. Reverse order to install including tightening center bolt to 35-55 ft-lbs. If this is your first stg wheel removal, try an old chevy, preferrably someone else's! If inexperienced, don't risk bruising your favorite Bimmer!!! Hope this helps you make your decision. Tater Todd

Posted on Jan 28, 2009

  • 11 Answers

SOURCE: Horn not Working, Ford Fiesta zetec 55

its most probably the clock spring which you need to take the steering wheel off to fit

Posted on Mar 07, 2009

  • 202 Answers

SOURCE: TURN SIGNALS WONT CANCELL CLASHING BROKEN PART SOUND IN STEERING WHEEL

you have to disconect the battery and leave it disconected for around a half and hour and then you can remove the air bag. Do not hook Battery back up untill it is all put back together

Posted on Apr 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing wing mirror electric on ford fiesta 2003 1400 zetec right hand side


Ooh..! It was a great idea. Its an innovating idea. you just careful while doing this or I recommend a mechanic to do this

Aug 05, 2016 | Ford Cars & Trucks

1 Answer

I have a 2003 1.6 petrol ford fiesta, it started by failing start up when warmed up. Cuts out while driving


Ford Fiesta Start-Up Flaw (CPU-Based) - YouTube

? 1:54
www.youtube.com/watch?v=Y78GTNBytSQ
May 29, 2012 - Uploaded by georgef551 I found a start-up flaw in the Ford Fiesta, when I occasionally tried to start the car quickly, and... ... this happened. I had them either fail to fully turn over, or other CPU-based starters wouldstart up the vehicle. ..... Ford Fiesta 2004 Lx 1.4 petrol mk6 won't start help ! ... 2012 Ford Fiesta Zetec 1.6 TI-VCT. Start .

Jul 27, 2015 | Ford Cars & Trucks

1 Answer

When i start the car theres a popping noise heard when the cars idle. can also here it more when idle and i turn the wheel slightly. any ideas what it could be.


petrol or diesel ?? if petrol is it a 1.6 zetec engine and not an american build with a monster engine?? ,well if its the zetec then i would check the power steering fluid level first then re poast if its ok

Sep 29, 2010 | 2003 Ford Focus

1 Answer

I need to put in another steering collum and I dont know how to do it.its a 91 ford F150.hope you can help me.I got another one out of the junk yard for 125,00 is that a good price .thanks for helping my...


I'd say $125.00 is a good price for a steering column.

First, have to remove steering wheel (but I don't have instructions for the steering column. For that, maybe try alldata.com, but that will cost):

STEERING Steering Wheel REMOVAL & INSTALLATION Without Air Bag EXCEPT F-SUPER DUTY STRIPPED CHASSIS MODELS AND MOTOR HOME CHASSIS MODELS Fig. 1: Remove the screws from behind the wheel - F-150 model without air bag 88288p12.jpg
Fig. 2: Pull away the cover with the wiring still connected 88288p13.jpg
Fig. 3: Disconnect the wiring at the steering wheel 88288p14.jpg
Fig. 4: Matchmark the steering wheel 88288p15.jpg
Fig. 5: Remove the center nut from the steering wheel 88288p16.jpg
Fig. 6: Use a steering wheel puller to remove the wheel 88288p17.jpg
Fig. 7: Remove the steering wheel from the shaft 88288p18.jpg
Fig. 8: Correct steering wheel installation 84928058.gif
NOTE: The factory recommends that the front wheels be set in the straight-ahead position and you paint or make chalk marks on the column and steering wheel hub for alignment purposes during installation. Of these two safeguards, it is more important to mark the column so even if the column is moved slightly, the steering wheel can still be repositioned in its original position.
  1. Disconnect the negative battery cable.
  2. Remove the one screw from the underside of each steering wheel spoke, and lift the horn switch assembly (steering wheel pad) from the steering wheel. On vehicles equipped with the sport steering wheel option, pry the button cover off with a suitable prytool.
  3. Disconnect the horn switch wires at the connector and remove the switch assembly. On trucks equipped with speed control, squeeze the J-clip ground wire terminal firmly and pull it out of the hole in the steering wheel. Don't pull the wire out without squeezing the clip.
  4. Remove the horn switch assembly.
  5. Remove the steering wheel retaining nut and remove the steering wheel with a puller. WARNING
    Never hammer on the wheel or shaft to remove it! Never use a knock-off type puller.
  6. Install the steering wheel in the reverse order of removal. Tighten the shaft nut to 40 ft. lbs. (54 Nm)
F-SUPER DUTY STRIPPED CHASSIS MOTOR HOME CHASSIS MODELS
  1. Set the front wheel in the straight-ahead position and make chalk marks on the column and steering wheel hub for alignment purposes during installation.
  2. Disconnect the negative battery cable.
  3. Remove the one screw from the underside of each steering wheel spoke, and lift the horn switch assembly (steering wheel pad) from the steering wheel.
  4. Disconnect the horn switch wires at the connector and remove the switch assembly.
  5. Remove the horn switch assembly.
  6. Remove the steering wheel retaining nut and remove the steering wheel with a puller. WARNING
    Never hammer on the wheel or shaft to remove it! Never use a knock-off type puller.
  7. Install the steering wheel in the reverse order of removal. Tighten the shaft nut to 30-42 ft. lbs. (41-57 Nm).
With Air Bag Fig. 9: Remove the air bag module and disconnect the wiring harnesses 88288g00.gif
CAUTION
Read the air bag service precautions in Section 6 prior to doing work involving an air bag equipped steering column component. Always wear safety glasses when servicing an air bag vehicle and handling the air bag to avoid possible injury.
  1. Turn the front wheels to the straight-ahead position.
  2. Disconnect the battery-to-starter relay cable for at least one minute to let the air bag back-up power supply discharge.
  3. Remove the air bag module from the steering wheel (refer to Section 6).
  4. Disconnect the horn/speed control wiring from the steering wheel.
  5. Remove the steering wheel retaining bolt.
  6. Install the Differential Bearing Cone Remover/Replacer, No. T77F-4220B1, or equivalent, and remove the steering wheel. Route the contact assembly harnesses through the steering wheel as it is lifted off of the shaft. To install: NOTE: Make sure the front wheels are still in the straight-ahead position prior to installation.
  7. Route the air bag sliding contact wiring through the steering wheel at the 3 o'clock position. Position the steering wheel on the shaft an align the marks. Make sure not to pinch the contact wire. WARNING
    Make sure no air gets trapped between the steering wheel and air bag sliding contact.
  8. Install a new steering wheel retaining bolt, then tighten to 23-33 ft. lbs. (31-45 Nm).
  9. Connect the horn/speed control wiring and clip in place. Connect the air bag wire harness. Tighten the module retaining nuts to 35-53 inch lbs. (4-6 Nm). NOTE: When the battery cable has been disconnected, then reconnected, some abnormal driving symptoms may occur for the first 10 miles (16 km) until the PCM re-learns it adaptive strategy.
  10. Connect the battery to starter cable. Verify the air bag warning indicator light on the instrument panel.
prev.gif next.gif

Sep 24, 2010 | 1991 Ford F150

1 Answer

Disarm and remove ford expedition air bags


Remove the negative cable from your car battery before replacing car air bags

Deactivate the air bag by removing the air bag fuses. Look in your car owners manual to locate the fuses

Unscrew steering column paneling and remove the airbag bolts on the back side of the steering wheel. Pull out the airbag until you see the back side and unplug the wires

Sep 24, 2009 | 2003 Ford Expedition

1 Answer

Replacing a Cruise Control Switch


Ford Taurus/Sable 1996-1999 Repair Guide
Steering Wheel
Removal & Instalation

e69ab1a.gif

Fig. 1: Remove the access covers for the air bag module retaining bolts

83ac520.gif

Fig. 2: Remove the air bag retaining bolts and...

d0a0934.gif

Fig. 3: Carefully remove the air bag from the steering wheel to access the wiring connectors

3344f1a.gif

Fig. 4: Detach the connectors...

12ea02c.gif

Fig. 5: ... from the air bag module

6e8ff5b.gif

Fig. 6: Remove the center bolt from the steering wheel

fef72e6.gif

Fig. 7: Install a suitable puller and tighten the forcing screw to...

4b45cbd.gif

Fig. 8: ... remove the steering wheel


CONTINUE...

Aug 19, 2009 | 1998 Ford Taurus

2 Answers

Horn keeps going off when driving. mk2 mondeo zetec ''W''


The air bag want go off.Its the contact conection under steering wheel that has brocken off.Your steering wheel has to be removed to replace this part.If you are going to attempt to change it ur self then disconnect the battery ground wire.This will stop the air bag going off.

Jul 07, 2009 | 2000 Ford Contour

1 Answer

Horn not Working, Ford Fiesta zetec 55


its most probably the clock spring which you need to take the steering wheel off to fit

Mar 04, 2009 | 2000 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...