Question about 2001 Dodge Dakota

2 Answers

How to remove door panel with a manual window

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How 2 remove door panel for a 06 buick lucer e drivers side front door

Posted on Jun 19, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,074 Answers

Screws in the armrest, clip on window crank, screw behind door handle and possible a screw behind a plug that is located to the inner or outer pane, then with a flat tip screwdriver gently pry around the outside of the panel then lift panel up and out. Good Luck Tim

Posted on May 22, 2011

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

ilragatzzo78
  • 241 Answers

SOURCE: 99 ford expedition power window

no, you will have to remove the window motor to raise the window up manually.

Posted on May 15, 2008

  • 78 Answers

SOURCE: Front Door Panel

push the door panel back around handle until you can see the clip facing dowhward then take a rag and pull in a upward position between the handle and door panel pull the rag in a right to left postion this will grab the clip and disengage it from the handle

Posted on Sep 27, 2008

  • 75 Answers

SOURCE: remove inside door panel without breaking it

they have push in clips that hold the panel on the door you can pull it off with your hand or go to parts store and buy a door panel removal tool
PLS take time to rate this solution and by the way you will probably need to buy new push in clips to hold panel on

Posted on Feb 17, 2009

  • 124 Answers

SOURCE: remove driver's door panel

Start prying the door panel off with a flat head screw driver. It's held on by plastic clips, and a few screws. just pry it back and look in there with a flash light, you'll see. Just pry them out. If your lucky you'll only break a few. No real easy way to remove those.

Posted on Mar 23, 2009

Monster80
  • 460 Answers

SOURCE: Need to remove door panel. Unable to unlock door with the key.

The linkages clips broke and the arms for the lock fell out not letting the key turn anything.

Posted on Apr 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REPLACE RIGHT REAR DOOR WINDOW ON 98TAURUS


Once you get the door panel off you can easily see how to remove the window which is riveted to the window regulator..Here are instructions for determining the rear door in a Taurus.
    • Pluck the window switch and lock switch from the rear door panel with the trim tool. Pull the wiring plugs out of each switch manually before setting the switches aside.
    • 2Remove the rear door panel retaining screws with either the Phillips screwdriver or socket set, depending on the year, make and model of your vehicle. If the panel will not lift off the rear door at this time, you may need to pry the door panel trim pins out of the door with the trim tool before removing the panel by hand. (This too will depend on the year, make and model of your vehicle.)
    • 3Raise the rear door window glass by hand and secure it with packing tape in the fully upright position to prevent unintended glass movement. Manually pull the wiring plug out of the rear window motor.
    • 4Remove the rear window motor retaining bolts with the socket set. Pull the old rear window motor out of the door through the door access hole. Position the new rear window motor in the door and bolt it in place with the socket set.
    • 5Reinstall the rear door panel on the rear door by reversing the door panel removal steps. Make sure to remove the tape from the window when done before you attempt to open the window.

Oct 04, 2012 | 1998 Ford Taurus

1 Answer

How do you remove a rear door panel on an Audi A3 4 Door


802771-a4_door_card_rear.gif

- Door trim.
Removal
- Unclip decorative panel -2-.
- Remove decorative panel -2- toward front.
- Remove bolts -3- (3x) from door trim -1-.
For vehicles with electric window regulators
- Window regulator switch, removing and installing Page 70-25 .
For vehicles with manual window crank
- Manual window crank, removing and installing Page 70-26 .
For all vehicles
- Unclip door trim -1-. Replace damaged clips Fig. 3
- Raise door trim -1- upward approx. 20 cm. out from door shell.
- Disengage Bowden cable for interior door mechanism Fig. 1 .
- Disconnect electrical harness connectors Fig. 2

Dec 03, 2010 | 2005 Audi A3

1 Answer

How do u remove the drivers side door panel to fix the window


YOU NEED CLIP REMOVAL TOOL TO REMOVE WINDOW CRANK HANDLE.YOU NEED DOOR PANEL FLAT TOOL REMOVE DOOR PANEL HATE TO SAY DOOR PANEL HAS AT LEAST 8 CLIPS LOCATIONS 4 CLIPS AT THE BOTTOM PANEL 2 CLIPS ON BOTH SIDES DOOR PANEL. YOU HAVE TO REMOVE 2 SCREWS HOLDING DOOR PULL CUP.YOU HAVE RELEASE CLIP BEHIND DOOR HANDLE USING TRIM TOOL.IF YOU HAVE TROUBLE GETTING DOOR PANEL OFF.HAYNES REPAIR MANUAL CAN HELP.

Oct 07, 2010 | 2004 Chevrolet Cobalt

1 Answer

Anywhere to find a breakdown to change the door handle that broke off on a 94 pathfinder?


Very easy to do...I have a 1990 and they are interchangeable....88-94: Door Panel
  1. Fully lower the door glass.
  2. Remove the arm rest, door lock knob and inside door handle escutcheon.
  3. For vehicles with manual windows, remove the regulator handle which is retained by a spring clip.
  4. Gently pry the door panel away from the door.
57cc694.gif
Interior side and floor trim removal procedures-Pathfinder

4c380d2.gif
Remove the lock button first before removing the door panel

e5a8f97.gif
Remove the plug to gain access to door panel retaining screws

54604ec.gif
Remove the trim cover

eec4f16.gif
Remove the door handle trim

09f640c.gif
Remove the power window switch trim panel

44a5e00.gif
After loosening the power window switch trim panel, disengage the electrical connection

530cf7c.gif
Remove all the necessary trim panels before removing the door panel clips

791f0b4.gif
View of the door panel retaining clip-clip must be installed in the hole straight

690538f.gif
Make sure the watershield plastic is in place before installing the door panel

Installation is the reverse of removal.

Dec 10, 2009 | Nissan Pathfinder Cars & Trucks

1 Answer

2003 ford taurus drivers window will not go up.


you either need a motor or motor and window regulator assembly.
SECTION 501-05: Interior Trim and Ornamentation 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Trim Panel Removal and Installation
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the front door trim panel screws.
  1. NOTE: To release the door trim panel two part pin-type retainers, first pull outward on the bottom of the door trim panel.
    Remove the front door trim panel.
    • Disconnect the electrical connectors.
c64985a.gif --------------------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Window Regulator And Motor
Special Tool(s) s2h~us~en~file=st1132a.gif~gen~ref.gif Heavy Duty Riveter
501-D011 (D80L-23200-A) or equivalent
Removal and Installation
  1. Remove the front door window glass. For additional information, refer to Front Door Window Glass in this section.
  1. Disconnect the front door window regulator motor electrical connector.
  1. Remove the window regulator rivets.
-----------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Door Window Regulator Motor Removal and Installation
  1. Close the window.
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the door trim panel. For additional information, refer to Section 501-05 .
  1. If equipped, remove the radio speaker.
  1. Position the watershield aside.
  1. Disconnect the door window regulator motor electrical connector.
  1. Remove the bolts and the door window regulator motor.
---------------------------------------------------

May 04, 2009 | Ford V6 Pony Cars & Trucks

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

1 Answer

Front right door window will not go up or down, it is electric. it works, some times, and some times not. it is in the down position. Would like to move to up position. I live in Arizona, I need it up for...


does it act the same whether you use the driver door switch or the passenger door switch? Please rate as fixya if this helps. thanks

here's repair procedure

Window Regulator, Front Door, Explorer Removal
srk~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel and front door trim shield . Refer to Section 01-05B .
Trim Panel, Front Door, Explorer Hi-Series, Two-Door and Four-Door Removal and Installation
  1. Remove the two screws retaining the front door trim panel (23942) located above the window regulator handle (23342) . Also remove one screw in the upper front portion of front door trim panel .
  1. Remove inside door handle cup (22634) at the window regulator handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.
  1. To remove window regulator control switch (14529) and outside rear view mirror control (17B676) , use notch located at lower end of outside rear view mirror control using a screwdriver to lift and remove.
  1. Remove outside rear view mirror control from front door trim panel pulling wire harness from inside of front door trim panel .
  1. From bottom of outside rear view mirror control, remove two screws and disconnect connector from switches. NOTE: Do not pull on the front door trim panel to remove clips from the inner panel holes.
  1. At each plastic clip location, pry the front door trim panel away from the door inner panel using the front door trim panel removing tool from Rotunda Moulding Trim Kit 107-00401 or equivalent. NOTE: Pay special attention to the cut-out in the door trim panel for the door handle, so that it clears the handle during removal without breakage.
  1. When wiring and disengagement of trim clips is completed, it is recommended that to remove panel, lift slightly to remove flange at the top of door trim panel from trough in the glass weatherstrip.
  1. Disconnect socket and bulb from illuminated interior lamp (13776) before total removal of front door trim panel. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the front door trim panel to the front door trim panel , firmly loading clips into slots provided on front door trim panel .

    Trim Panel, Front Door, Explorer Hi-Series Four-Door

    a9ce4e4.gif
  1. Remove inside door belt weatherstrip and glass stabilizer.
  1. Remove front door window glass as described in this section.
  1. Remove two nut and washer assemblies attaching the equalizer bracket.
  1. Remove three rivets (manual) or four rivets (power) attaching the regulator base plate to front door trim panel finish panel (23712) .
  1. Remove window regulator electric drive and front door window channel bracket from vehicle.
  1. Working on a bench, carefully bend tab flat to remove arm slides from front door window channel bracket .
  1. Install new window regulator electric drive arm plastic guides into front door window channel bracket and bend tab back to 90 degrees. Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket . Make sure rubber bumper is installed properly on new front door window channel bracket , if replacement is made.

    9b5ccd1.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Steps 7 and 8 of Window Regulator, Removal.
  1. Install front door trim panel finish panel with preassembled glass bracket into vehicle. Set the regulator base plate to window regulator electric drive using base plate locator tab as a guide.
  1. Install three (manual) or four (power) rivets (385189-S100) to attach regulator to front door trim panel finish panel . Two 1/4-20 x 1-inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (3-5 ft-lb). Equivalent metric retainers may be used.
  1. Install equalizer bracket.
  1. Install inside door belt weatherstrip and glass stabilizer.
  1. Lower regulator arms to access holes in front door trim panel finish panel . Install front door window glass as outlined.
  1. Adjust glass to ensure proper alignment with glass run. Cycle glass for smooth operation.
  1. Install front door trim panel and front door trim shield . Refer to Section 01-05B .

Apr 20, 2009 | 1994 Ford Explorer Limited

1 Answer

Replace a window regulator in a 1994 ford explorer


wow, a lot of work to do.

Window Regulator, Front Door, Explorer Removal
srk~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel and front door trim shield . Refer to Section 01-05B .
  1. Remove inside door belt weatherstrip and glass stabilizer.
  1. Remove front door window glass as described in this section.
  1. Remove two nut and washer assemblies attaching the equalizer bracket.
  1. Remove three rivets (manual) or four rivets (power) attaching the regulator base plate to front door trim panel finish panel (23712) .
  1. Remove window regulator electric drive and front door window channel bracket from vehicle.
  1. Working on a bench, carefully bend tab flat to remove arm slides from front door window channel bracket .
  1. Install new window regulator electric drive arm plastic guides into front door window channel bracket and bend tab back to 90 degrees. Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket . Make sure rubber bumper is installed properly on new front door window channel bracket , if replacement is made.

    4a5a8fb.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Steps 7 and 8 of Window Regulator, Removal.
  1. Install front door trim panel finish panel with preassembled glass bracket into vehicle. Set the regulator base plate to window regulator electric drive using base plate locator tab as a guide.
  1. Install three (manual) or four (power) rivets (385189-S100) to attach regulator to front door trim panel finish panel . Two 1/4-20 x 1-inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (3-5 ft-lb). Equivalent metric retainers may be used.
  1. Install equalizer bracket.
  1. Install inside door belt weatherstrip and glass stabilizer.
  1. Lower regulator arms to access holes in front door trim panel finish panel . Install front door window glass as outlined.
  1. Adjust glass to ensure proper alignment with glass run. Cycle glass for smooth operation.
  1. Install front door trim panel and front door trim shield . Refer to Section 01-05B .

Apr 11, 2009 | 1994 Ford Explorer Limited

1 Answer

Removal of rear door panel to access power window motor


SECTION 501-05: Interior Trim and Ornamentation 2000 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Rear Door Trim Panel Removal and Installation
  1. Remove the rear door trim panel screws.
  1. NOTE: The rear door trim panel has eight two-part pin-type retainers. The male part of the retainer will remain with the trim panel and the female part will remain with the door.
    NOTE: To release the door trim panel pin-type retainers, first pull outward on the bottom of the door trim panel.
    Remove the rear door trim panel.
    • Disconnect the window regulator control switch electrical connector.
  1. To install, reverse the removal procedure.

Apr 07, 2009 | 2000 Ford Taurus

1 Answer

Door panel removal


The book says 1. remove panel pull strap 2. remove door handle bezel 3. on 1995-2001 models,remove power accesory panel and trim panel upper extension. 4. remove armrest screws and pad. 5. remove window handle,I guess if not power windows.
KD makes a tool to go in between door panel and door to pop the door clips loose. KD 3705
You will also have to have a window crank tool if it is manual window. KD431
Hope that will help.

Mar 23, 2009 | 2001 Chevrolet Silverado 1500

Not finding what you are looking for?
2001 Dodge Dakota Logo

529 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...