Question about 1999 Pontiac Grand Prix

1 Answer

Where are the bolts located on the pump - 1999 Pontiac Grand Prix

Posted by on

  • Ed Micknius May 22, 2011

    What pump are you referring to. And what is the engine size( for example 3.1L)

  • gary buckhanon Jul 16, 2013

    v6 3800

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,252 Answers

Water pump, fuel pump, oil pump, smog pump??????what size motor???

Posted on May 22, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replace water pump 1995 aurora


Water Pump REMOVAL & INSTALLATION 3.5L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Partially drain the cooling system.
  3. Remove or disconnect the following:
    • Water pump pulley bolts, loosen but do not remove at this time
    • Drive belt
    • Idler pulley
    • Water pump pulley
    NOTE: The water pump is attached to the engine with both long and short bolts, be sure to note their locations.
    • Water pump and discard the gasket
    NOTE: Note the locations of the 5 long bolts.
  4. Clean the water pump mounting surface. Fig. 1: Be sure to install the 5 long water pump bolts in the correct locations - 3.5L engine 9300z502.gif
    Fig. 2: Water pump mounting - 3.5L engine 9300z503.gif
    To install: NOTE: Be sure to install the 5 long bolts in the proper locations.
  5. Install or connect the following:
    • Water pump using a new gasket. Torque the bolts to 124 inch lbs. (14 Nm).
    • Water pump pulley
    • Idler pulley. Torque the bolt to 37 ft. lbs. (50 Nm).
    • Drive belt
  6. Refill the cooling system.
  7. Start the engine and check for leaks.
3.8L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    • Serpentine belt
    • Heater and bypass hoses from the water pump
    • Water pump pulley
    NOTE: The long bolt can be removed by aligning the bolt head with the frame rail hole.
  5. Install an engine support fixture.
  6. Remove or disconnect the following:
    • Torque axis mount
    • Water pump and discard the gasket
    To install: Fig. 3: Exploded view of the water pump and mounting bolt locations - 3.8L engines 7922xg01.gif

  7. Thoroughly clean all the sealing surfaces.
  8. Apply a thin bead of sealer around the outside edge of the water pump
  9. Install or connect the following:
    • New gasket
    • Water pump. Torque the inlet and outlet side bolts to 29 ft. lbs. (39 Nm) and the remaining bolts to 97 inch lbs. (11 Nm).
    • Torque axis mount
  10. Remove the support fixture.
  11. Install or connect the following:
    • Water pump pulley
    • Water pump hoses
    • Serpentine belt
    • Water pump pulley bolts. Torque the bolts to 115 inch lbs. (13 Nm).
    • Negative battery cable
  12. Refill the cooling system.
  13. Start the vehicle and check for proper operation.
4.0L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    • Air inlet duct
    • Water pump drive belt cover
    • Water pump drive belt
    • Lower radiator hose and bypass hose
    • Thermostat housing from the water pump housing
    • Water pump from the water pump housing, by turning the locking ring with a Water Pump Remover/Installer tool J-38816
    To install: Fig. 4: Exploded view of the water pump housing and water pump - 4.0L engine 7922xg02.gif

  5. Install or connect the following:
    • Water pump, seat the locking ring
    • Thermostat housing to the water pump housing
    • Lower radiator hose and coolant bypass hose
    • Drive belt and drive belt cover
    • Air inlet duct
    • Negative battery cable
  6. Refill and bleed the cooling system.
prev.gif next.gif

Jan 24, 2011 | 1995 Oldsmobile Aurora

4 Answers

Where is the fuel pump


REMOVE THE REAR BACK SEAT BOTTOM TO GAIN ACCESS, THE SEAT IS HELD IN BY 2 BOLTS. YOU WILL NEED A 10MM OR 12MM SOCKET TO LOOSEN THE SEAT. BOLTS ARE LOCATED BETWEEN THE SPACE WHERE THE SEAT MEETS THE SEAT BACK. WHERE THE REAR SEAT BELTS COME OUT. WHEN BOLT ARE REMOVED PUT YOUR HAND BETWEEN THE SEAT AND PULL UP YOU WILL SEE WHERE THE FRONT HALF OF THE SEAT IS SECURED BY A 'L' SHAPE BRACKET LOCATED IN THE FRONT HALF OF THE REAR SEAT GOING INTO THE FLOOR BOARD.

Jan 13, 2011 | 1996 Acura TL Series

1 Answer

Location of the waterpump?


Looking at belt routing below, the water pump is the pulley all the way to the right, will have 4 10mm bolt's holding the water pump pulley, loosen 4 small bolt's on water pump pulley, remove serpentine belt, remove small water pump pulley bolt's all the way off, remove pulley, now you can see water pump, remove small 8mm bolt's from water pump, now water pump will come right off, hope this was very helpful.

a49399b.gif

Aug 19, 2010 | 2003 Chevrolet Malibu

1 Answer

REPLACE WATER PUMP


3.0L OHV Engine

  1. Disconnect the negative battery cable. Allow the engine to cool.
  2. Remove the radiator cap and drain the cooling system.
  3. Loosen four retaining bolts securing the water pump pulley to the water pump hub.
  4. Remove the accessory drive belts.
  5. Remove the automatic belt tensioner.
  6. Disconnect and remove the heater hose from the water pump.
  7. Remove the engine control sensor wiring from the locating stud bolt, if equipped.
  8. Remove the water pump-to-engine retaining bolts and lift the water pump and pulley up and out of the vehicle.
To install:
  1. Clean the gasket surfaces on the water pump and engine front cover. Install a new gasket on the water pump using gasket adhesive.
  2. Place the water pump in position on the engine with the pulley and four retaining bolts loosely installed on the hub.
  3. Apply pipe sealant to bolt No. 3. Refer to the accompanying illustration for bolt location.
  4. Install the bolts in the water pump housing.
  5. Tighten bolts Nos. 4, 5, 6, 7, 8, 9 and 10to 15-22 ft. lbs. (20-30 Nm). Tighten bolts Nos. 11, 12, 13, 14 and 15 to 71-106 inch lbs. (8-12 Nm).
The bolts are of different lengths and must be installed in the correct locations.
  1. If equipped, attach the engine control sensor wiring to the locating stud bolt.
  2. Hand-tighten the water pump pulley retaining bolts.
  3. Install the accessory drive belts.
  4. Tighten the water pump pulley bolts to 15-22 ft. lbs. (20-30 Nm).
  5. Connect the heater hose to the water pump.
  6. Fill the cooling system. Connect the negative battery cable.
  7. Start the engine and allow it to reach normal operating temperature. Check for leaks and proper operation.

3.0L DOHC Engine
  1. Disconnect the negative battery cable. Drain the engine cooling system.
  2. Remove the water pump drive belt.
  3. Disconnect the radiator and heater hoses from the water pump.
  4. If equipped, remove the A/C compressor-to-water pump brace.
  5. Unfasten the four nuts securing the water pump to the engine and remove the water pump.

To install:

89da3e5.jpg

Fig. : Water pump mounting-3.0L DOHC engine
  1. Clean the water pump to engine gasket sealing surfaces.
  2. Install the water pump using a new gasket and install the four retaining nuts. Tighten the retaining nuts to 15-22 ft. lbs. (20-30 Nm).
  3. Connect the radiator and heater hoses to the water pump. Make sure the clamps are securely tightened.
  4. If equipped, install the A/C compressor-to-water pump brace. Tighten the brace bolts to 15-22 ft. lbs. (20-30 Nm).
  5. Remove the water pump drive belt.
  6. Fill the engine cooling system, then connect the negative battery cable.
  7. Start the engine and allow it to reach normal operating temperature, then check for coolant leaks and proper engine operation.

Hope this helps (remember rated this).

Aug 10, 2010 | 1999 Ford Taurus

1 Answer

Oil pump ,,,where is the oil pump located on a 1997 dodge caravan


Hello
Welcome!
Oil pump is located on the oil pan.
Parts needed,,,oil,,,, oil filter,,,, oil pan gasket,,, oil pump,,,, oil pump pickup tube..
time to do this,, about 3 hours
Instructions,
Raise van place on 2 jack stands
drain oil remove oil filter fill new filter install.
remove bolts from oil pan,
remove oil pan..
remove 2 bolts that hold oil pump and tube.

install new pump and tube tork bolts to 45 fp
replace oil pan gasket and install oil pan
tork pan bolts to 35" pounds
install drain plug
fill with oil
start and check for leaks

let me know if i can help more

Jul 17, 2010 | 1997 Dodge Caravan

1 Answer

Change the water pump. what size is the bolts


Location, size and torque specification for the water pump bolts-3.0L OHV engine...

f2d2658.jpg

  • Install the bolts in the water pump housing.
  • Tighten bolts Nos. 4, 5, 6, 7, 8, 9 and 10to 15-22 ft. lbs. (20-30 Nm). Tighten bolts Nos. 11, 12, 13, 14 and 15 to 71-106 inch lbs. (8-12 Nm).
    The bolts are of different lengths and must be installed in the correct locations.
  • If equipped, attach the engine control sensor wiring to the locating stud bolt.
  • Hand-tighten the water pump pulley retaining bolts.
  • Install the accessory drive belts.
  • Tighten the water pump pulley bolts to 15-22 ft. lbs. (20-30 Nm).
  • Connect the heater hose to the water pump.

Hope this help (remember rated and comment this post).

Apr 10, 2010 | 1999 Ford Taurus

1 Answer

How to replace a water pump on a 2001 ford taurus


This is for a 3.0L and VIN S engine--

VIN U Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Accessory drive belt and tensioner
    • Water pump pulley
    • Heater hose
    • Engine control sensor wiring
    • Water pump
54afbf0.gif
To install:
NOTE The water pump bolts are of different lengths and must be installed in the correct locations.

  1. Install the water pump. Tighten bolts 1, 2, 3, 4, 5, 6, 7, 8, 9 and 15 to 15–22 ft. lbs. (20–30 Nm). Tighten bolts 10, 11, 12, 13 and 14 to 72–106 inch lbs. (8–12 Nm). Refer to the accompanying illustration for the bolt locations.
  2. Install or connect the following:
    • Engine control sensor wiring
    • Heater hose
    • Water pump pulley and tighten the bolts to 15–22 ft. lbs. (20–30 Nm)
    • Accessory drive belt and tensioner
    • Negative battery cable
  3. Fill the cooling system and check for leaks

Dec 08, 2009 | 2001 Ford Taurus

1 Answer

Where is the fuel pump located on a 73 Duster 318


Should be located on the block, passenger side, down low, and more at the front of the vehichle. It is a mechanical pump and bolted to the block with either 2 or 3 bolts, should have 2 or 3 steel lines cominng out of it.

Sep 17, 2009 | 1983 Plymouth Gran Fury

1 Answer

Tension bolt


It has to be located just above the belt near the power steering pump. Common sense will let you know that the tension bolt will tighten or lossen the belt.

Nov 08, 2008 | 2002 Kia Optima

1 Answer

Oil pump location


Pump is external, located right side timing cover housing. Find the oil filter...there you are. Pump has 2 hidden bolts. Remove oil filter to access bolts.

Aug 14, 2008 | Oldsmobile Cutlass Cars & Trucks

Not finding what you are looking for?
1999 Pontiac Grand Prix Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...