Question about 2006 Toyota Sequoia

Open Question

How do you replace the light bulb for the License plate in a 2006 Sequoia ?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: replacing bulbs marker light license plate light

***

Mine's a 2001, but I think 2002 is the same.
I found this site/question when searching for the answer today.
Now that I had to muddle through it on my own I thought it only fair that I spread the knowledge.

My 2001 has two license plate lights, one on either side of the plate mounting area.
There is a slot at the top of each light bezel that at first appeared to me to be where you might insert a screwdriver or hooked tool to pry/pull out the bezel.
This proved NOT to be the case.
If you forge ahead heavyhandedly in this direction you will risk breaking the lens.
If you look very carefully at the top of the slot you will find a tab that is VERY thin and thus hard to spot at first glance.
take a thin flat screwdriver and insert it gently ABOVE the tab.
Press down gently but firmly, and coax, or lightly pry the lens out.
Once you have it out, rotate the gray plastic piece directly behind the reflector portion of the lens about a 1/8 turn in a counter clockwise direction.
At this point you can access and change the push-in type "OS 12V W5W E1 2GL w0T" bulb.

To reassemble just reverse the directions.
When snugging the assembly back into the license plate area, first position the bottom and then tip the top into position until you feel/hear it click.

Done!

Celebrate your victory over your machine!

Peace,

Rob

***
***

Posted on Oct 18, 2008

  • 65 Answers

SOURCE: I have a 2004 Toyota

You have to remove the rear door inside panel.First thing is to remove the top and side interior trim panels,they just pop out by prying them away after they are out the metal retaining clips sometimes stay in the door,pull them out and put them on the plastic panel before reinstalling.Then the strap that you use to close it has a cover on it that you have to push up to get off then remove the 10 mm bolt that holds the strap.Then pry the panel away from the door I think that the bottom has two hooks on it which means that the top needs come off first so you can lift the panel hooks out of the slots.Once the panel is off you will see the bulbs they twist out and you have to pull the bulbs out.Good luck

Posted on Nov 29, 2008

  • 2 Answers

SOURCE: how to replace license plate light bulb

open back hatch in the center there is a rectangle shaped piece of plastic pop it out and you will see the wire on the back of the bulbs

Posted on Dec 04, 2008

  • 1 Answer

SOURCE: Light Bulb Replaement

I just replaced the license plate lamps on my 2004 Deville DTS.
Lamp is PC195. Lamp PC168 will also work, (it was in my car for the last two years), but it is a brighter bulb than needed.

You pop out the lamp holders by pushing (sliding)the right side towards the left. That little push will unhook plastic tabs from the sheet metal and the right side of the lamp holder will release from the trunk. See the attached photo.

To push the lamp holder, I used a narrow putty knife covered with masking tape. A screwdriver will work as well. The masking tape protects the paint from scratches.

Posted on Jan 08, 2009

  • 840 Answers

SOURCE: 2002 license plate bulbs

its real simple look at the license plates then look up you will see 2 screw per lamp / unscrew them and slide remove its a 194 bulb so get some ready then replace and put back / Please rate my response thank you very much

Posted on Feb 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Plate light does not work, but lights are good and sockets seem good


check bulb the number plate light runs on the same circuit as the side lights so if they are working its got to be a bad earth on the plate light

Jan 24, 2016 | Cars & Trucks

2 Answers

Tail lights work but why don't license plate lights?


The license plate lights have their own separate bulbs. If you are able to replace the bulbs, that may solve your problem. If not, you may have a loose or rusted connection to the plate bulbs only. If you are able to gain access, you may want to check the condition of the harness that supplies the power to the license plate portion. Good luck and have a great day.

Aug 30, 2015 | 2001 Toyota Tacoma

1 Answer

How to replace license plate bulb in trunk lid 2006 buick century


If you can not get to bulb, Look at the light lens on trunk license plate. There may be screws on the lens to undue to get to bulbs. Good-Day!

Sep 01, 2014 | Cars & Trucks

1 Answer

I need to know how to replace the license plate bulb on a scion xa


Email Chris Bacon here: www.autolumination.com
*License Plate Light Bulb Size: 168
I buy all of my bulbs there.

Sep 09, 2012 | 2006 Scion xA

1 Answer

2006 Nissan Quest license plate bulb replacement


WOW WOW Brother !!! ..... BRAKE LIGHTS ?? Side panels ??..... They need help with license plate bulb located on the hatch..... Where are you going ??..

May 29, 2012 | Nissan Cars & Trucks

1 Answer

Need to replace bulbs that lights license plate. License plate and light is part of trunk


raise trunk lid look on the inside behind your license plate light there should be access to the bulb there. You will see the wires going in to the bulb there will either be a flt plate that can be removed to access bulb or where the wires enter there will be a round socket that you can twist counter clockwise and remove the bulb socket for bulb replacement. hope this helps.

Jan 15, 2011 | 2003 Lincoln Town Car

1 Answer

License plate bulb needs replacing


Remove license plate. Unscrew the screws on the underside of the bumper. Slide the lights back toward the trunk and then down through the opening. Unscrew bulb and replace with a new one.

Reverse steps to reinstall the lights.

Feb 06, 2010 | 2003 Chevrolet Impala

1 Answer

2006 lincoln towncar Burnt out light bulb


I recommend autozone if you buy the bulb from them they will assist you but I believe it has to be replaced from inside the trunk

Jan 12, 2009 | 1999 Lincoln Town Car

2 Answers

2006 Chevy Equinox--


There are two screws in each lens. Remove those screws and carefully pry the lens off. I did it recently. It worked well for me

Oct 11, 2008 | 2006 Chevrolet Equinox

Not finding what you are looking for?
2006 Toyota Sequoia Logo

Related Topics:

293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...