Question about 2000 Chevrolet Astro

3 Answers

Where is the EBCM module located on a 2000 Chevy Astro Conversion Van / 6 cylinder engine ? How do I remove Module ?

Posted by on

  • waltk8s May 22, 2011

    where is the EBCM module located on a 2000 Chevy Astro Conversion Van, 6 Cylinder Engine ? Show Diagram. How do I remove Module ?

  • waltk8s May 22, 2011

    where is the EBCM module for the ABS Brake System located on a 2000 Chevy Astro Conversion Van / 6 cylinder ? How do I remove module ?

×

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 17,970 Answers

The EBCM (Electronic Brake Control Module) is mounted to the BPMV (Brake Pressure Modulator Valve) located at the left front (lower) engine compartment.

EBCM Removal & Installation Procedure

  1. Remove the Brake Pressure Modulator Valve (BPMV). Refer to the Hydraulic Control Unit (BPMV) procedure in this section.
  2. Remove the 4 T-25 Torx® bolts (1) from the EBCM (2). (click image for zoom)

    where is the EBCM module located on a   2000 Chevy - zjlimited_1272.jpg

    Fig. Bolts (1), EBCM (2), bracket (3), bolts (4) and BPMV (5)

  3. Disconnect the 2-way ABS pump motor connector.
    WARNING Do not use a tool to pry the EBCM or the BPMV. Excessive force will damage the EBCM.
  4. Remove the EBCM (2) from the BPMV (5). Removal may require a light amount of force.
    1. Do not reuse the EBCM mounting bolts. Always install new bolts.
  5. Clean the EBCM to BPMV mounting surfaces with a clean cloth.
To install:

WARNING Do not use RTV or any other type of sealant on the EBCM gasket or mating surfaces.
  1. Install EBCM (2) onto BPMV (5).
  2. Install the 4 EBCM bolts (1).
    1. Tighten the 4 bolts to 39 inch lbs. (5 Nm) in an X-pattern.
  3. Connect the 2-way ABS pump motor connector to the EBCM.
  4. Revise the tire calibration using the Scan Tool Tire Size Calibration function.
  5. Use the scan tool to check and clear DTC memory.

Hope this helps.

Posted on May 23, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,381 Answers

Ignition Module


  • Removal & Installation



  1. Remove the engine cover.
  2. Disconnect the electrical connector (3).
  3. Remove the screws (4) holding the ignition control module (2) and the heat sink (1) to the bracket.
  4. Remove the ignition control module and the heat sink.

  5. where is the EBCM module located on a   2000 Chevy - perkins48_1045.jpg

    Fig. Exploded view of ignition module-4.3L engine .
    To install:

    1. Install the ignition control module (2) and the heat sink (1) on the bracket with the screws (4).
      1. Tighten the screws to 31 inch lbs. (3.5 Nm).

    2. Reconnect the electrical connectors (3).
    3. Install the engine cover.
    4. perkins48_1047.jpgDuralast/Ignition Control Module,part#DR178 for 75.99 at Autozone.

Posted on May 22, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

The ebcm is electronic brake control module and is ontop of the anti lock brake system module if its bad its bad and needs to be replaced ,
The anti lock brake system module has all brake lines attached to it under the hood on the left side

Posted on May 22, 2011

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 chevy trailblazer code co131 brakes capliars locking up


DTC C0131 Antilock Brake System (ABS)/Traction Control System (TCS) Pressure Circuit

The master cylinder pressure sensor is located within the brake pressure modulator valve (BPMV). The master cylinder pressure sensor signal, to the electronic brake control module (EBCM), increases as hydraulic pressure in the front brake circuit increases.

Conditions for Setting the DTC co131
Any of the following conditions may cause the DTC to set.
• The EBCM detects open master cylinder pressure sensor circuitry.
• The EBCM detects shorted master cylinder pressure sensor circuitry.
• The master cylinder pressure sensor self-test, which occurs at power-up, fails.
• The zero-pressure signal voltage is not within an acceptable range.
• The master cylinder pressure is not within an expected tolerance based on deceleration rate and other data available to the EBCM.

1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle
2
Inspect the vehicle for the following and ensure that there is no base brake failure:
• Dragging brakes
• Faulty parking brake switch
• Brake fluid leakage
• Air in hydraulic system
• Seized brake calipers
• Swollen, kinked or otherwise damaged brake hoses
Did you find and correct the condition?
YES - Go to Step 9
NO - Go to Step 3
3
Drive the vehicle in order to verify that the brakes do not self-apply during turning maneuvers.
Do the brakes self-apply during turning maneuvers?
YES - Go to Symptoms - Hydraulic Brakes
NO - Go to Step 4
4
Use the scan tool to clear the DTCs.
Turn OFF the ignition for 5 seconds.
Turn ON the ignition.
Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?
YES - Go to Step 5
NO - Go to Diagnostic Aids
5
Select the vehicle stability enhancement system (VSES) Data Display function on the scan tool.
Observe the Brake Switch Status parameter while pressing and releasing the brake pedal.
Does the Brake Switch Status change while pressing and releasing the brake?
YES - Go to Step 6
NO - Go to DTC C0161
6
Remove the electronic brake control module (EBCM) from the vehicle. Refer to Control Module References .
Inspect the master cylinder pressure sensor connector within the EBCM for damage or corrosion.
Is there connector damage or corrosion present?
YES - Go to Step 8
NO - Go to Step 7
7
Important: Following EBCM replacement, perform the set-up procedure for the EBCM. Use the scan tool to perform the Tire Size Calibration procedure.
Replace the EBCM. Refer to Control Module References .
YES - Did you complete the replacement?
NO - Go to Step 9
--
8
Important: Following EBCM replacement, perform the set-up procedure for the EBCM. Use the scan tool to perform the Tire Size Calibration procedure.
Replace the EBCM and the brake pressure modulator valve (BPMV). Refer to Control Module References .
YES - Did you complete the replacements?
NO - Go to Step 9
--
9
Use the scan tool Clear All Class 2 DTCs function to clear all of the DTCs from all modules.
Turn OFF the ignition for 5 seconds.
Turn ON the ignition.
Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?
YES - Go to Step 2
NO - System OK

Mar 13, 2017 | Cars & Trucks

2 Answers

I have a 2000 Corvette and the Check Engine light came on, power was decreased and it said check Active Handling System...what does this mean and what kind of problems does it create?


Have the codes checked. There are to many possibilities for your car to list. Repost with the codes. Kind of problems it creates is lost power and handling.

Apr 18, 2015 | 2000 Chevrolet Corvette

1 Answer

Need fisical location of the ECBM on my 2005 safari cargo van


The EBCM (Electronic Brake Control Module) is mounted to the BPMV (Brake Pressure Modulator Valve) located at the left front (lower) engine compartment.

EBCM Removal & Installation Procedure
  1. Remove the Brake Pressure Modulator Valve (BPMV). Refer to the Hydraulic Control Unit (BPMV) procedure in this section.
  2. Remove the 4 T-25 Torx® bolts (1) from the EBCM (2). (click image for zoom)

    zjlimited_1548.jpg
    Fig. Bolts (1), EBCM (2), bracket (3), bolts (4) and BPMV (5) (click image for zoom)

  3. Disconnect the 2-way ABS pump motor connector.
    WARNING Do not use a tool to pry the EBCM or the BPMV. Excessive force will damage the EBCM.
  4. Remove the EBCM (2) from the BPMV (5). Removal may require a light amount of force.
    1. Do not reuse the EBCM mounting bolts. Always install new bolts.
  5. Clean the EBCM to BPMV mounting surfaces with a clean cloth.
To install:

WARNING Do not use RTV or any other type of sealant on the EBCM gasket or mating surfaces.
  1. Install EBCM (2) onto BPMV (5).
  2. Install the 4 EBCM bolts (1).
    1. Tighten the 4 bolts to 39 inch lbs. (5 Nm) in an X-pattern.
  3. Connect the 2-way ABS pump motor connector to the EBCM.
  4. Revise the tire calibration using the Scan Tool Tire Size Calibration function.
  5. Use the scan tool to check and clear DTC memory.

Hope this helps.

Jul 06, 2011 | 2000 GMC Safari

3 Answers

Ebcm motor relay circuit problum


Motor relay circuit this is for the ABS, you will need ot restore the third eye brake light and check fuse in the engine junction fuse box, (cigarette lighter fuse) make sure it didnt open

May 15, 2011 | Chevrolet Tahoe Cars & Trucks

3 Answers

I need a fire timing order for a chevy astro van v6


THE FIRING ORDER IS AS FOLLOWS : 1-6-5-4-3-2.
CYLINDER NUMBERS (front-to-rear) :
LEFT (driver side) 1-3-5
RIGHT (passenger side) 2-4-6

To set ignition timing, ensure that engine is at operating temperature, (190 degrees or above), bypass EST (electronic spark timing) by unplugging the single tan wire with a black stripe from the distributor. Ignition timing should be set at 0 degrees or TDC (top dead center). If not, loosen distributor hold down bolt and adjust, then retighten.

Mar 05, 2010 | 1993 Chevrolet Astro

1 Answer

2000 astro van won't start


What you have to do is check and see if you have fuel pressure.You have to remove the engine cover to check it.If you don`t have a pressure tester then remove the air cleaner hose to the engine and spray it with carb.cleaner or brake cleaner.If it starts for a few seconds then it is more than likely a fuel pump.If it does not start then you have to check for spark at the spark plugs.Make sure you check more than one plug.If no spark then you have to check the distributor cap and rotor.Make sure the rotor is good and cap also.Things that can cause no spark are the ignition module,coil,and cap and rotor.Hope this helps.Good luck.

Jan 29, 2010 | 2000 Chevrolet Astro

1 Answer

1997 chevy astro van


The control module is located just behind the ignition coil. Sorta hard to get to but we got it and the van is running great.

Dec 21, 2008 | 1997 Chevrolet Astro

Not finding what you are looking for?
2000 Chevrolet Astro Logo

Related Topics:

3,834 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...