Question about Ford Bronco II

1 Answer

2 of the holes that the bolts screw into that hold the servo on are stripped. How can that be fixed without taking it all apart or dropping the transmission? ....or can it be fixed? Please help

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,074 Answers

Http://www.wikihow.com/Fix-a-Stripped-Screw-Hole

Posted on May 22, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2008 grizzly 700 and it won't drive (move) in 2wd. I only can drive in 4 wheel drive. Any thoughts on how to diagnose what the problem could be? Please help


This is the electric motor inside your servo that actuates your 4wd/2wd/diff locker. When the servo goes out on these bikes, it's more than likely the small electric motor. Simply pull the servo off the front differential, open it up and you will see the small motor inside. I pulled the complete diff out in the instructions due to having to change a seal but you can do this with it still in the bike.



If you have a skid plate on you will have to remove it to access the bottom bolt on the servo. I also recommend having the bike in 2wd to ease in installing the servo back on the diff.

Remove the 3 bolts that hold the servo on the diff. Gear oil is going to pour out unless you drain it first.
Soory last pic 5
26147106-wuoh52pvdxpwqpeytk4hf153-3-0.jpg Once removed installation is the opposite. Just be sure not to turn anything inside the casing once you open it. The small worm gear on the motor doesn't matter just don't turn anything else.

Install back on the bike fill with gear oil and enjoy your 4wd and the money you saved.
pic 1
26147106-wuoh52pvdxpwqpeytk4hf153-3-2.jpg
pic 2
26147106-wuoh52pvdxpwqpeytk4hf153-3-5.jpg Once the servo is removed from the diff. Remove the six T-25 tamper resistant tq screws that hold the servo together.

Once you get the screws out, carefully pry the servo apart taking extra care not to turn the gears inside.

Once apart it will look like this.
pic 3
26147106-wuoh52pvdxpwqpeytk4hf153-3-9.jpg You can see the two screws that hold the little motor in.
pic 4
26147106-wuoh52pvdxpwqpeytk4hf153-3-14.jpg
Remove those two screws and carefully pry up on the motor and remove it and the small gear attached to the end of it.

Picture of the motor removed.

Mar 31, 2016 | Cars & Trucks

Tip

How to quick fix Stripped Sheet Metal Holes Without a Sweat!!!


Have you ever been there??? Been where you ask??? Well been at the end of a job with just one screw left to be installed as a last and final touch to a door skin or some other type of trim molding and found the hole was stripped out and the screw you have to put into the hole is "swimming" in the hole due to it being oversized? you try using a self tapper screw and same results too loose not dependable to secure anything appreciable.
Ok I have a quick and easy savior for all you guys out there in
mechanicsville.
Go into your tool box or small parts/screw cabinet and pull out a cotter pin and that same self tapping screw that is a bit smaller then the stripped out hole, bend the cotter pin out straight and form an "L" shape with it...insert the small L angle shape into the hole... then with a little finess work the self tapping screw into the hole at the same time allowing the screw to be buffered off the cotter pin on the side of the hole, thread the screw into the hole holding the cotter pin steady and "Walla" screw goes down tighter then it ever fit before, if need be get your dykes and clip off the excess cotter pin material left outside the hole.
Hope this works for you.
Happy Motoring!!

on Jul 17, 2010 | Chevrolet El Camino Cars & Trucks

1 Answer

How do i remove rear passenger door panel on 2006 freelander


I just finished doing this so I am going to put the steps in order and very clear:

Remove the one screw which hold the plastic under the door latch. Do this first since if you take window control piece out first and you drop the screw it ill go into the door and you might have trouble finding it later.

Pull up on the plastic with the window control, using a flat head screw driver, come up easy. Unplug the wire.

Pry off the cover on the door pull arm, start from the bottom comes off easy again with flat screw driver.

Unscrew the three screws (large flips head), Pull out the screws and save so you don't loose.

Start from the bottom and pull out the panel now from the door, using a weed puller or a long flat head screw driver. Most come out OK, if they come off the panel you can reattach to the panel.

Lift panel off door and up and it is done.

Window motor assembly is attached to the door by 3 bolts. It is attached to the window with one other bolt (10 mm, all of them). Window needs to be down 2/3 of the way so you can access the bolt.

The motor and other parts comes out of the hole pretty easy.

Install new assembly, attach wire, lower window so the connector for the window attachment is moved down (it comes in the up position).

Attach window with the bolt. Attach the assembly to the door (3 bolts).

Put the panel back up in reverse order.

I have taken a lot of doors apart and this was actually one of the easiest, Freelander is a piece of junk in maintenance department so good to know how to take it apart. Have to take the other side apart soon to fix the door lock actuator.

May 26, 2012 | Land Rover Freelander Cars & Trucks

1 Answer

Starter bolt stripped. Helicoil or tap?


Either way ,is a lot of work. First thing I would try is a little bit longer bolt. Take a screw driver and push into the stripped hole to determine how long you can go.Even 1/4 inch more threads might be enough to hold starter secure. A little sealer on threads would be good.. If all that fails ,try to oversize the bolt and retap.Make sure the oversize bolt will go through the starter. I have had good success with J B WELD [brand] to drill and retap. Just make sure the surface is clean

Feb 25, 2011 | 1991 Nissan 300ZX

2 Answers

Installing thermostat with gasket. will not go in without rolling gasket off.


Use some gasket glue to keep the gasket in place if you have some handy. Although i find the best way with troublesome gaskets is to make some guide bolts. find 2 bolts the same thread and diameter as the thermostat cover hold down bolts. Cut the heads off the 2 bolts, screw into bolts holes and drop the gasket over the top. Drop the termostat and cover down, hold pressure against the cover and slowly replace the guide bolts with the good original bolts. Tighten up and all should be in place. Hope that is helpful

Jan 23, 2011 | Pontiac Grand Am Cars & Trucks

1 Answer

Licence plate falling off


why not drill to seperate holes and put self tapping bolts in to hold it on simple fix

Mar 05, 2010 | 2003 Nissan Murano

1 Answer

2000 Neon hasn't had the air filter changed in at least 2 years because the one of the screws that holds it in has the top of it stripped. Can anyone recommend how to solve this issue without costing an...


Is possible, on your Neon to remove the entire air cleaner assembly? If you can get the assembly out on work bench maybe you can get on it with a "Vise-Grip" (locking plier) and get it out. Or take electric drill and drill the bolt out and replace it with new. When you say it's stripped do you mean the threads are stipped and it spins but won't come out? Or, is the head of the bolt or screw stripped out and the wrench or screwdriver won't grab it? If you do get it apart make sure you put some grease or anti-sieze compound on the threads of the bolts so they won't rust in. Good luck!

Dec 08, 2009 | 2000 Dodge Neon

2 Answers

Can't remove brake drums


Matthew, look for two threaded holes on the brake drum. Use a approx. 8mm bolt to force the drum off. If not, loosen the brake shoes from behind in case there is a ridge on the inside of the drum preventing the drum from coming off. Other than that, take a hammer and hit outside of the center hub to free drum from hub.

Aug 16, 2009 | Kia Sedona Cars & Trucks

2 Answers

How do I put back the transmision filter?


you need to find it asap or you will have to re place the tran ok.

Apr 09, 2009 | 2004 Nissan Sentra

2 Answers

1999 Chevy S10


Just pull the dash back a little by undoing all the bolts and screws, its going to be a tight fit find someone with small hands.

Oct 21, 2008 | 1999 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...