Question about Toyota Land Cruiser

Open Question

Please what is the cylinder head torque for a hzj75 toyota ute. the ute doesn't work to feed the starving cows. please help urgent cheers cherry

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

Ad
  • 1 Answer

SOURCE: torque setting cylinder head bolt 4 cylinder KIA sportage

I need the torque settings and pattern for a Kia Sportage 2.2

Posted on Jan 28, 2010

  • 181 Answers

SOURCE: Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS

You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM

Posted on Feb 19, 2010

Pelukes01
  • 52 Answers

SOURCE: what are the cylinder head torque settings for a

0900c1528006efe6.jpgUmiformilly tighten each of the ten head bolts in several passes, in the sequence shown. Tighten them to 44 ft. lbs. (60 Nm).

Posted on Jul 23, 2010

leedavidian
  • 1420 Answers

SOURCE: what do i have to

Welcome to FIxYa.com



Alternator BELT REMOVAL

1. REMOVE BATTERY AND BATTERY TRAY

2. DISCONNECT POWER STEERING (PS) RESERVOIR TANK

3. REMOVE DRIVE BELTS

a. Loosen the lock bolt, pivot bolt and adjusting bolt.

b. Remove the 2 drive belts.

GENERATOR BELT INSTALLATION

1. INSTALL DRIVE BELTS

a. Install the drive belts.

b. Adjust the drive bell with the adjusting bolt.

c. Tighten the pivot and adjusting lock bolts.

Torque:

Pivot bolt: 59 N.m (600 kgf.cm, 43 ft.lbs

Lock bolt: 21 N.m (210 kgf.cm, 15 ft.lbs

2. CONNECT POWER STEERING (PS) RESERVOIR TANK

3. INSTALL BATTERY TRAY AND BATTERY

leedavidian_162.jpgleedavidian_163.jpgleedavidian_164.jpg



Thank you for using FixYa.com

Regards, Lee Davidian

Posted on Dec 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque settings of cylinder head toyota quantum 2.7 vvti petrol


Cylinder head cover sub-assy x Cylinder head sub-assy 9 92 80 in.?lbf

Cylinder head sub-assy x Cylinder block sub-assy 1st - 39 398 29

Feb 12, 2016 | Toyota Cars & Trucks

1 Answer

Torque Settings


It would be really helpful to find out what Year, Make, Model of vehicle you have and also engine size & trans type. The specs are different from one vehicle to another.

Feb 21, 2015 | Cars & Trucks

1 Answer

Toyota 5afe head bolts torque


Toyota 4A/ 5A-FE Cylinder Head Torque:
(a) Apply a light coat of engine oil on the threads and under the heads of the cylinder head bolts.
(b) Install the plate washer to each cylinder head bolt.
(c) Install and uniformly tighten the ten cylinder head bolts in several passes in the sequence.
Torque: 60 N-m (610 kgf-cm, 44 ft-lbf)
HINT: Cylinder head bolts are in length of 90 mm
(3.54 in.) and 108 mm (4.25 in.). Install the 90 mm
(3.54 in.) bolts (A) in intake manifold side positions.
Install the 108 mm (4.25 in.) bolts (B) in exhaust
manifold side positions.

Mar 31, 2014 | 2003 Toyota Corolla

1 Answer

I need the torque settings for toyota corola 1993 cylinder head torque please ?


Hi Manuel, There are a number of different engines used in the Corolla, knowing which would be a great help. The engines used in the 1993 are of the 'A' series and 'E' series. The torque for the A series is 29 nm + 90 degrees. When removing the head begin loosening from the outer bolts. When the head is off have it inspected for warpage and skimmed if it is required. Tightening any cylinder head always begins at the middle or centre and works outwards. As my friend has said, the camshaft caps are tightened to 9 nm and the inlet manifold goes to 24 nm, and the exhaust is 27 nm. The tappet cover I think is 29 nm. The tappet cover is tightened on the A series with nuts onto the plug tubes. Regards John

Mar 29, 2014 | 1993 Toyota Corolla

1 Answer

Torque specification


Apply a light coat of engine oil on the threads and
under the heads of the cylinder head bolts.
- Install the plate washer to each cylinder head
bolt.
- Using Torque wrench, install and uniformly tighten the ten
cylinder head bolts in several passes.
Torque: 60 N-m (610 kgf-cm, 44 ft-lbf)

Jan 26, 2014 | 1993 Toyota Corolla

1 Answer

I HAVE AN AUDI A4 TDI X REG, IVE GOT THE CYLINDER HEAD OF. WHAT IS THE HEAD BOLT TORQUE AND IS THERE A SEQUENCE TO TORQUE THEM CHEERS.


Audi A4 1.9 TDI-PD (Pumpe Duse)

Cylinder head tightening sequence:

tdisline_853.jpg
Renew bolts!

Torque settings:
1. Stage 1 = 40 Nm
2. Stage 2 = 60 Nm
3. Stage 3 = 90 Degrees
4. Stage 4 = 90 Degrees

Please do rate my response. Thanks!

Sep 01, 2011 | Audi A4 Cars & Trucks

1 Answer

Help please What torque are the cylinder head bolts on peugeot expert 1.6 hdi 2008 i need to put the head back on


no problem the correct setting is ,hmm it says tighten to 20nm then 40nm and then slacken off 130? and tighten 130? ,well this the proverbial brown stuff from a cow to me as when i do these engine i pull down with a speed key then a rachet then my 80cm snap on bar so i suppose iam pulling down to around 75/80 lbs per inch but in all honesty i never use a torque wrench as i used to torque heads in ford of dagenham at 18yrs old so three engine a minute i just sort of feel for the bolt stretch and that it really .

May 03, 2011 | Peugeot Liberte Cars & Trucks

1 Answer

I need the torque settings for a Toyota Corolla 1995 model 4afe engine TORQUE SETTINGS FOR THE CYLINDER HEAD? PLEASE PLEASE HELP


cylinder head bolts:

step one: 22 Ft-lbs.
step two: tighten additional 90 degrees
step three: tighten additional 90 degrees

Feb 22, 2011 | 1995 Toyota Corolla

1 Answer

What do i have to loosen to put on new air con belt on 1997 hzj75 ute


Welcome to FIxYa.com



Alternator BELT REMOVAL

1. REMOVE BATTERY AND BATTERY TRAY

2. DISCONNECT POWER STEERING (PS) RESERVOIR TANK

3. REMOVE DRIVE BELTS

a. Loosen the lock bolt, pivot bolt and adjusting bolt.

b. Remove the 2 drive belts.

GENERATOR BELT INSTALLATION

1. INSTALL DRIVE BELTS

a. Install the drive belts.

b. Adjust the drive bell with the adjusting bolt.

c. Tighten the pivot and adjusting lock bolts.

Torque:

Pivot bolt: 59 N.m (600 kgf.cm, 43 ft.lbs

Lock bolt: 21 N.m (210 kgf.cm, 15 ft.lbs

2. CONNECT POWER STEERING (PS) RESERVOIR TANK

3. INSTALL BATTERY TRAY AND BATTERY

leedavidian_162.jpgleedavidian_163.jpgleedavidian_164.jpg



Thank you for using FixYa.com

Regards, Lee Davidian

Dec 23, 2010 | 1997 Toyota Land Cruiser

2 Answers

Torque setting cylinder head bolt 4 cylinder KIA sportage


I need the torque settings and pattern for a Kia Sportage 2.2

Nov 24, 2009 | 2001 Kia Sportage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...