Question about Buick Century

2 Answers

So the front side o f the motor is the intake and the the rear is the exhaust side

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,044 Answers

In a sideways mounted motor yes.

Posted on May 21, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,252 Answers

What make and model and size motor?????

Posted on May 21, 2011

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Ford ranger 2.3 dual coil firing order

the cylinder # 1 is at front exhaust side
firing order 1342 front coil to left side(intake)
rear coil to right side (exhaust) check the numbers at the coils.

Mar 12, 2017 | Ford Cars & Trucks

1 Answer

1997 Nissan pickup 2.4 head torque sequence

From repair manual for 1996 KA24E 2.4L engine:

Number bolts as follows:
Exhaust side, front to rear - 8, 6, 1, 3, 9
Intake side, front to rear - 10, 4, 2, 5, 7

Tighten bolts in numbered sequence, five steps.
Step 1 - 22 ft-lbs
Step 2 - 58 ft-lbs
Step 3 - loosen all bolts completely
Step 4 - 22 ft-lbs
Step 5 - 54-61 ft-lbs

Oct 19, 2014 | 1997 Nissan Pickup

1 Answer

Push rod diagram

Exhaust push rods are longer
  • 6.0740 Inch Overall Length
  • Standard Size
  • Intake valves are
  • 5.7460 Inch Overall Length
  • Standard Size. Front head.
front head standing in front of car passenger to driver side
Ex , in ,in Ex ,in Ex

rear head standing in front of car passenger to driver side
Ex. ,In , Ex , In , In , Ex

remember exhaust push rods are longer
Rocker arm bolt ................................ 124 lb. 30 degrees

Apr 21, 2014 | 1999 Pontiac Grand Am GT

1 Answer

What are the correct rockers/lifters to order when replacing ALL of them on 97 nissan pickup?

A normal sohc 4 cyl. has 4 intake and 4 exhaust.
That motor has 8 intake valves (2 in each cyl.) and 4 exhausts.
I thought all the lifters were the same ,but if what you say is correct you need 4 intake front ,4 intake rears and the 4 exhaust,if they were all bad.

Jan 20, 2014 | Nissan Cars & Trucks

1 Answer

Location of camshaft position sensor on 2009 saturn aura

2.4L cmp sensor exhaust located upper rear of the engine near camshaft cover. 2.4L cmp sensor intake located upper front of the engine near the camshaft cover. the 3.5L cmp sensor located right side of engine compartment above the timing chain cover.below power steering pump.3.6L cmp sensor located right side of the engine near the front and rear.

Sep 26, 2013 | Cars & Trucks

1 Answer

Where is the air intake

Your air intake is the big aluminum piece at the back side of your motor parallel to your valve cover. If you look at your motor, the exhaust manifold is on the front of the motor, and the air intake manifold is on the back of the motor near the firewall. Hope this helps

Jan 02, 2013 | 1986 Toyota Corolla 2 Door

2 Answers

Which side of the motor on a 3.1 buick 1998 century is the intake side and the exhaust side. I'm installing push rod that are different lenghts and call for exact positioning on the intake side as well...

That is a V6 or V8 standard mounted engine. When they say intake side and exhaust side they are talking about the valves. Typically each cylinder has 2 valves the front valve is the intake the back valve is the exhaust.If you haven't already gotten it I highly recommend you get the Haynes or Chilton's repair manual from your vehicle so you have the adjustment specs or priming procedure if you have hydraulic lifters.

May 20, 2011 | 1998 Buick Century

1 Answer

2001 jeep wrangler 4.0 new motor new intake new ecm and when you start it the motor instantly goes to 3000 + rpms. what will cause this???

There is a vacuum leak from installing the intake. Common problem. The exhaust and intake use a common gasket. When reinstalling the exhaust manifold, there are two guide pins, one front of the manifold and one in the rear. What usually happens is that the manifold sits ON these pins when installed and it creates a vacuum leak when the engine is started that instantly races the engine. The manifold has to be removed and when reinstalled, MAKE SURE the pins are IN the guideholes on the manifold.

Feb 18, 2011 | 1998 Jeep Wrangler

2 Answers

Where is the thermostat 3.1 engine

If facing the front of the car, Right (drivers' side) side of motor next to exhaust pipe just above transmission in the side of the intake. You will have to remove the air intake to see the housing.

Nov 24, 2010 | 1997 Chevrolet Lumina

1 Answer

Timing marks for the Dodge 2.4L caravan, 2000

To align both sets of timing marks, turn engine crankshaft to the right with belt on cam and crank. Once you have done this the crankshaft alignment mark (on front of crankshaft gear) will line up with mark to the rear of gear on engine block.The two cam gear timing marks should be alines across from one another. The right cam gear is the intake side and the left side is the exhaust side. After removing the belt turn the exhaust cam down 1/2 notch. Timing mark on exhaust 1/2 notch down from the intake side. Install new belt and recheck everything to make sure it's all correct. Hope this will help you.

May 16, 2010 | 2000 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts


Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides