Question about Dodge Ram Pickup 2500

1 Answer

No power to the pump it works if hooked directly to the battery

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

The motor has shorted out. you can test this off the battery directly.
Check for a warranty or a recall on this item
It maybe replaced for free of charge

Posted on May 21, 2011

  • frank thomas wilson
    frank thomas wilson May 22, 2011

    sorry,,, I was thinking wrong.... check the power steering pump relay instead

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My new fuel pump only primes when wired direct?


Well you need to get out the DVOM - digital volt ohm meter an check for battery voltage at the fuel pump relay ! if you replaced it you saw the holes it plugs into in the relay / fuse box ? Put you volt meter on the 20 volt scale , hook the black lead to the battery negative or a good engine ground an take the red lead an touch - don't stick it in an spread the terminals . Two of the holes should have battery voltage ,if not check the EEC power relay ! If you find voltage at two holes change the meter to ohms , leave the black connector on a good ground an touch the red to the two holes left , one should be open or OL on the meter , this is the control side from the engine computer . the last hole should show a few ohms resistance , this is down through the wiring to an through the fuel pump to ground . You have two different wiring circuits , control an load side , load side being power to the fuel pump an control side is power an the engine computer supplying a ground energizing the relay closing the contacts in the relay sending battery voltage to the fuel pump. Test don't guess !

May 25, 2015 | 1987 Ford Ranger

1 Answer

My bilge pump will not work when i push the switch on the dash. It works when it is hooked direct to battery. Why is this


The switch could be defective or there could be a defect in the wiring between the switch and the pump.

Jul 06, 2014 | Cars & Trucks

1 Answer

Were is the fuel pump relay on a 91 geo tracker also when I hooked power to the fuel pump it dindnt run


When you hooked power directly to the fuel pump, it may not have been grounded properly. If you're running power directly to it, and it is grounded properly, it should work fine, unless the fuel pump itself if bad. There is something called Ohm's law. it says you have to have power and a ground to transfer electricity. I am at a loss on where the fuel pump relay is. If the pump won't work with direct power, I can't imagine it being the relay.

Aug 10, 2013 | 1995 Geo Prizm

2 Answers

No power to fuel pump


Also check the timing belt2_bing.gif.and or relay.
If the distributor is not turing the fuel pump also will not run.

Hope this tip helps.

Hope thid Tip Helps.

R/
David

Jan 25, 2010 | 1993 Toyota Pickup

1 Answer

Fuel pump only works if I hook it up direct to battery


I would look for a fuel pump relay, you may need the manual to find out where it is.
or bang on the relays till it starts running, sometimes you can swap relays around if they are the same.
gd lk
Eric

Aug 25, 2009 | 1990 Toyota Pickup

2 Answers

Have a 1992 chevy 1500 truck fuel pump works fine when hooked directly to the battery, replaced fuel pump relay, still no power to the fuel pump, engine turns over fine


maybe check the fuse for the injectors...i was being stupid and did this, if that fuse is missing it wont work even if your fuel pump works fine. i think its labeled inj a+b.

Jul 26, 2008 | Chevrolet 1500 Cars & Trucks

1 Answer

There is no power to the fuel pump, the fuse is good, also if I hook it up direct it works


what are you by-passing in order to hook it up directly? If the fuse isn't bad but it runs if you put wires directly to the positive and negative wires at the pump, then I'd say it's a bad ground connection between the ecm/fuse box and the pump.

Jul 25, 2008 | Chevrolet Suburban 1500 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...