Question about 2001 Hyundai Accent

1 Answer

Timing my timing tensioner broke so i put new one in and cant figure how how to get the timing right. i tried to follow the diagram that came with tensioner. my '01' is a 1.5 12v sohc. so i tried the diagram for that setup and it didnt work, so i tried the the digram for the 1.6 16v dohc which looks more like the setup for my car and that still didnt work. i dont understand where i went wrong please help me?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

Try http://www.hmaservice.com/. You can register for free.

Posted on Aug 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My serpentine belt broke and now i dont know how to put a new one back on


buy a new serpentine belt and refer to the diagram on the box. it will show you how to route the belt. also, there is a belt tensioner. it can be pulled back with a large prybar so you can slip the belt on the pulley.

Nov 20, 2010 | 1987 Pontiac 6000

1 Answer

Have a 2000 chevy malibu. Serpentine belt broke. can you put it on easily by moving tension bar?


yes, follow the diagram under the hood. get it threaded right then move the tension pully to allow it to get on the last pully and your done.

Oct 08, 2010 | 2000 Chevrolet Malibu

3 Answers

I need a belt routing diagram for a 2000 ford taurus 24v dohc engine. Know where I can find one on the web? (No sticker under the hood. And I was dumb enough not to pay attention when I took it off.)


OK, one doesn't need a belt routing diagram to reinstall a new belt.

Just route the belt so that one by one you put the ribbed part of the belt up against the ribbed pulleys, and the smooth part of hte belt up against the smooth pulleys. Do this until one arrives at the tensioner and release tension with a breaker bar to put the belt on the final tensioner pulley.

Check that the tensioner has enough spring load for the belt to maintain the right friction against all of the serpentine pulleys.

That's all there is to it.

Sep 09, 2010 | 2000 Ford Taurus

1 Answer

Belt broke that drives the water pump and alternator on my 88 plymouth reliant. another belt in the way, and cant figure out how to get the new belt on.


You can loosen the alternator that should releive the tension on the belt.
When you tighten it again make sure you can only turn the belt 90 degrees then you know you have the right tension.

Jul 11, 2009 | 1988 Plymouth Reliant

1 Answer

Alternator belt fell off


You may have to buy a new belt because that one may have stretches. After you buy a new belt. Look at he alternator, it has two screws, one hold it in place and the other allow it ti move. Lose both a little. With a pry bar push the alternator so the belt can fit. Look for the belt routing diagram in the engine compartment. Follow it and put the belt on. You were suppose to have a belt tension tool to determine the tension. Then use your pry bar to move the alternator to position and tension then tightened alternator screws.

Mar 13, 2009 | 1998 Mazda 626

1 Answer

Audi serpentine belt problem


are you sure you put it on the right way go to autozone.com and get a belt diagram. did you put the belt on upsidedown?

Mar 07, 2009 | 2001 Audi A6

5 Answers

How do you change a serpentine belt on a 2003 Oldsmobile Alero?


Brute force - you have to pry up the tensioner pulley. The way we did it was put the belt over the alternator and A/C compressor, and get it back in place around the main bearing pulley. Then we took a bar and forced up the tensioner and slid the belt over the main bearing pulley. Voila . . .

Jan 14, 2009 | 2001 Oldsmobile Alero

1 Answer

Need to install new serpentine belt on 96 Jetta 2.0


that is your belt tensioner!! You pull that back when you are gettin ready to finnish putting your belt on the last pulley!! Follow diagram under hood for your specs on motor!!

Dec 07, 2008 | 1996 Volkswagen Jetta

Not finding what you are looking for?
2001 Hyundai Accent Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...