Question about 2006 Jeep Grand Cherokee

1 Answer

How do you turn on the back-up distance sensor - not the button on the dash that starts as soon as you put the car in reverse?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 13 Answers

ADHFJYJRTHHD

Posted on May 21, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to disable Prius back up beep


This is a pretty easy fix.

1. Keep you foot on the break and turn the car on.
2. Press the odometer/trip button until your dash displays the odometer mileage.
3. Turn the car off and while keeping your foot on the break, restart the car by pressing the on button.
4. Immediately press and hold down the Odometer/trip button for at least 10 seconds.
5. While still holding down the Odometer/trip button put the car in reverse. You will hear the reverse beeping. Then push the park button.
6. You can now release the Odometer/trip button and if you keep pushing the button you can toggle the beep to come on or turn off by looking on your dash. It should say "b-on" or "b-off".
7. Toggle it to the "b-off" setting and put your car in reverse and that annoying beep should be turned off.

Jan 14, 2014 | 2008 Toyota Prius

1 Answer

Tail light wire


Adjust the brake pedal switch located on the upper side of the brake pedal under the dash. To adjust the stop light switch, disconnect the two wires attached to the rear of the switch, move the switch by loosening the lock nut towards the brake pedal. As soon as the center pin of the switch begins to touch the brake pedal notch, rotate the switch half turn more and lock it by tightening the lock nut. Connect the wires back and ask your companion to see the tail lamps while you depress and release the brake pedal. Or you can see the tail lamp behavior by parking the car on reverse at a distance of one foot from any wall.

Nov 30, 2013 | Toyota Previa Cars & Trucks

2 Answers

2003 altima dash fuse blows when i put in reverse and alternator stops working


It is electrical, could be initiated by mechanical (shift lever mechanics are pinching a wire in reverse) or a shorted wire or solenoid in the reverse light system or transmission solenoid circuit. Need a detailed wiring diagram to determine path of circuit for that fuse. That is where you need to start. Try your local library or dealer for a service manual. Look Online also.

Nov 02, 2013 | Cars & Trucks

1 Answer

Just bought a 96 rav4.need instructions about when and when not to engage the 4wheel button . 5 speed manual has the differental lock button on dash


Hi Ed, The 4 X 4 is selected after slowing to about 20 mph and is best deselected at standstill or very slow speeds. On occasions you may have to stop and reverse a short distance to get disengagement. The differential lock should be engaged in the same way as the 4 X 4. It should be used only if traction is lost and the vehicle loses traction with a wheel spinning free. Never use diff lock on hard top roads and always disengage as soon as possible. Regards John

Feb 26, 2013 | 1996 Toyota RAV4

1 Answer

I have a 2003 isuzu rodeo. Sometimes it is hard to put into reverse. I can usually get it to work in 1 or 2 tries. the abs light came on a couple of times. what could make this happen?


I do not think shifting gears ,putting your car in reverse has nothing to do whit whit the abs to come on and off ,my isuzu rodeo did the same thing and it was a dirty sensor ABS on front wheels , There is a ring on the inside of the front disc's that works together with the ABS sensor to send information to the car computer when braking ,and must have a distance of about 1/8 of an inch between ring and sensor ,,they must not touch ,what happens is that over time dirt starts to build between sensor and ring ,and ring and sensor begin to touch ,and if they do touch ABS light will start be on and off while driving ,,most of the time the problem is the sensor and not necessarly a bad sensor ,,only a durty sensor and dirty ring ,a broken or loose wire also will activate the ABS light ,,,and about car hard to put into reverse ,you'll probably need a new clutch ,,good luck

Sep 18, 2010 | 2003 Isuzu Rodeo

2 Answers

Having problem with back up sensors shutting off when i put it in revers, in drive the button works fine but as soon as i put it in reverse the light comes on indicating that the sensors are off


Might want to check the lens for the reverse sensors to make sure they are not damaged or dirty.
Next is to check the wire from the back to the sensors, some times the connectors become corroded and if the sensors are not "seen" by the PAM ( Parking Aid Module ) the system turns on, then off right away.
The sensors remove from the back of the bumper ( they do not pull through to the outside ), and the wiring harness is fairly easy to track. Check each sensor and the connector for the sensor harness.

Apr 17, 2010 | 2005 Ford F-150

1 Answer

Park Assist Doesn't work On 2007 Solara


first try backing up close(6ins) to a wall then put car in reverse(sensors are powered by reverse lights circuit)see if it makes a noise when you press on/off button.if no then make sure you have reverse bulbs working,then check fuses.

Mar 08, 2010 | 2007 Toyota Solara

1 Answer

Ford backup sensors not working


I would buy a Chilton Repair Manual from a local parts store and a digital ohm meter. If the chilton doesn't have the ohms for all the sensors then research online for the specs on the sensor. It sound like a wiring issue or relay.

Mar 25, 2009 | 2005 Ford F 350 Super Duty

Not finding what you are looking for?
2006 Jeep Grand Cherokee Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...