Question about 2000 Jaguar S-Type

1 Answer

How do you take door panel off of jaguar s type 2000 reg

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 21 Answers

Hi you take the panels off carefully .. rear door, there are lots of clips around the outer edge of the panel, but about 2" in .. approx one near each corner and one in the middle of each length and width also in the centre of the panel. Look inside the door pull, (armrest) lift the end of the rubber and lift it out, there are two screws under it. remove them .. starting at the bottom outer edge of the door, slide the plastic tool under the panel to find the first clip, locate the clip in the Vee, then slide the screwdriver down the middle of the tool to release the first clip, (they are tight, they might also slide out of the coloured clip anchor, spacer, it's ok) work your way round the door up both sides to the top, (at this point remove the bezel from around the interior door handle see below)

be careful along the top, remember the clip in the middle on the top section, too much force here will damage the panel .. always used the plastic tool you made to protect the panel.

Remove bezel .... use plastic tool or piece of plastic. . to protect trim ..
remove the bezel around the interior door pull, be careful, it is a very tight fit, there are three fixing points, clips, this is very flexible but it could break, start with the front edge, widest part, there are two clips here one top one bottom approx one third distance from the end of the bezel, at the end where the levers are mounted there is on clip centrally .. I suggest you release each clip in turn and then, this will seem wrong, but ease the narrow end, hinge end out of the panel first, gently prise between the end of the clip and the panel. .. when it is out, and it is a very tight fit, but it is flexible enough to come over the levers, gently work it over the levers. After removal continue to release clips along top of panel ..

plastic tool ... take the top from and icecream tub. cut it to approx 5"x4" .. score it gently down the middle with a knife then fold it along the score so that you have 5"x2" doubled .. then at the end cut a 'V' approx half inch wide at the top (through both thickness) to locate around the panel clips,
Remember to take all the sharp edges from the plastic tool so that it doesn't damage the trim or the paint, also if you later remove the lock lever assembly put masking tape over the outside door lever to protect the paintwork .. when you replace the trim mount all of the clips back on the panel first, be carful with the middle clip on the top edge .. hope that helps. sk


Posted on May 21, 2011

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 420 Answers

SOURCE: S Type JAguar Rear Door

First remove all of the screws, some will be hidden under plastic caps, then take a door panel tool (about $5.00 at a parts store) and work it around the panel popping out the plastic keepers. Be carefull and try not to damage the panel where the keepers attach, you can buy new keepers at any auto part store and even Lowe's and Home Depot carry them.

Posted on Jul 18, 2009

  • 1 Answer

SOURCE: window stuck in door panel

See
http://www.automotiveforums.com/vbulletin/showthread.php?p=4253203

Posted on Aug 03, 2008

  • 1986 Answers

SOURCE: 2000 jaguar s-type driver window will not roll up

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Pull back the weather seal and you'll be able to see the motor, regulator, guide rails

Posted on Sep 10, 2009

swolfinor
  • 504 Answers

SOURCE: how to program 2000 S type garage door opener

GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Posted on May 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The rear window automatic open and close system has stopped working on my jaguar stype,reg t55 jms


On both rear windows, or just one? If its just one then probably the regulator mechanism in the door has broken (there are some rather fragile plastic parts that can snap with age). The mechanism is easily replaced by removing the door trim (take out two screws found under the rubber mat in the door handle well, and pry off the whole door panel with a wide blade screwdriver or cats paw (start at top edge nearest to rear - 4-6 snap fittings should pop off reasonably easily). Unscrew old mechainsm and replace the whole thing.. Parts usually available on Ebay for $50 to $100, make sure you get the correct orientation, front and rear, and left and right, are all different parts - Lincon LS parts also fit perfectly).

If both windows not working and stopped at the same time... sounds electrical.. start checking fuses?

Jun 29, 2011 | 2000 Jaguar S-Type

1 Answer

My batteries are flat in My Jaguar S type 2000 reg, I want to open the luggage compartment but, I dont know how.


Use the ignition key, there is a key manual opener on the boot lid either on the trim or under the handle by the registration plate, use some WD40 first as the lock will be stiff from no use. hope this helps.

Mar 02, 2011 | 2000 Jaguar S-Type

1 Answer

How to remove doorpanel Jaguar xkr 03


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls.

Oct 22, 2009 | 2000 Jaguar S-Type

1 Answer

How to remove the front dorr panel on s type jaguar to repair door mirror


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls and mirror. Then you can access the bolts securing mirror onto the door

Oct 20, 2009 | 2000 Jaguar S-Type

4 Answers

Driver window on 2000 s type jaguar off track


You will have to remove the screws to door panel, remove window and lock controls. Then gently pry the plastic studs out of the door and lift the panel up and off. You will now have access to track and window

Sep 10, 2009 | 2000 Jaguar S-Type

1 Answer

S Type JAguar Rear Door


First remove all of the screws, some will be hidden under plastic caps, then take a door panel tool (about $5.00 at a parts store) and work it around the panel popping out the plastic keepers. Be carefull and try not to damage the panel where the keepers attach, you can buy new keepers at any auto part store and even Lowe's and Home Depot carry them.

Jul 18, 2009 | 2000 Jaguar S-Type

1 Answer

DRIVER WINDOW WANT GO DOWN


hey jonest21,
I agree with emissionwiz, the fuse is most likely not the problem. Ive seen this numerous times. The window regulators on these older s types are very weak, and break all the time. They are fairly expensive to replace, and the dealership will charge at least an hour and a half for labor.
The door panel has to come off in order to get to the door panel. If you are goin to attempt this by yourself post it that you are, and ill give you more help on removing the parts.

May 19, 2009 | 2000 Jaguar S-Type

1 Answer

How to program 2000 S type garage door opener


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

Apr 21, 2009 | 2000 Jaguar S-Type

4 Answers

Jaguar rear window removal


I followed the instructions given by your expert Richard.His instrutions were clear and precise,and I had the problem solved in 5 minutes.best regards A.Taylor

Jul 02, 2008 | 2000 Jaguar S-Type

Not finding what you are looking for?
2000 Jaguar S-Type Logo

1,612 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...