Question about 2000 Chevrolet Malibu

1 Answer

My turn signals stopped working and my hazard light don't work either. I had problems for a while now they just stopped working? help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 226 Answers

Its your flasher. for either switch you must disassemble the steering column. The signal flasher switch is the first switch you will encounter. The hazard switch is a little farther down the column.Iif your looking to replace the flasher unit . There are 2,one for the signals & one for the hazards. Look under the dash,near the fuse block,they are normally small round cylindrical units that plug in with either 2 or 3 spade terminals. The signal flasher is usually plugged into the fuse block, the hazard flasher is usually near by with just wires plugged into it.be aware that if your going into the steering column you will need special tools

Posted on May 21, 2011

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

wilsodfarm
  • 986 Answers

SOURCE: 1998 Dodge 2500 pickup turn signals, hazards

There is a conector box on the left side of your steering wheel on the colum loosen it and check your wires I bet when you just loosen the block they will start working,I hope this helps you

Posted on Oct 08, 2009

kirkx
  • 2019 Answers

SOURCE: turn signals and hazard light not working

Sounds like the falsher unit itself is bad.
Looks sort of like a small relay, in the fusebox. Turn signals and emergency lights use the same flasher.

Posted on Jun 26, 2009

  • 3 Answers

SOURCE: I have a 1999 Plymouth Breeze 2.0. My turn signals

have you checked the bulbs and the fuses?

Posted on May 22, 2011

wyet_helps
  • 339 Answers

SOURCE: brake lights don't work when

{: ) Looks like your lightings got haywired. Have you had vehicle repairs recently? Anyway, it seems that you have poor grounding connections for the affected lightings. Some circuits share common ground, and ground terminals are strategically distributed on the vehicle. If these grounds don't have good contact with the body, chassis, or engine ground, circuit functions are badly affected. Thats why these ground points should be inspected and kept clean and tight, maintain that good wire and terminal contacts.
We can start with G100 located at the Left Front of the Engine Compartment on the left front body mount. See diagram below:


wyet_helps_24.gif Check out also G401 which is located in the chassis harness, mounted to the left rear Body mount. This ground point is shared by the rear lamps like the brakes, reverse, and rear signal lamps.
If possible check also other ground points that you may visually come across while on your search. Be sure also that fuses are all inspected good.
I hope we get lucky in finding and fixing a certain lamp function, if not all. Goodluck.

Posted on Aug 10, 2011

  • 93 Answers

SOURCE: Flashers don't work, emergency and turn

you may have a blown fuse. that would be where i would look first.

Posted on Aug 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

5 Answers

98 chevy lumina Rear window break light works, but rear break lights don't, also right turn don't work?


I can almost 100% guaranty the turn signal switch is the problem. Power for the brake lights starts at the brake switch. power then splits from there and the third brake light gets power directly from the brake switch. Since the turn signal and the brake lights are on the same bulb power for the brake lights is routed through the turn signal switch. the switch depending on what position it is in will allow brake power or turn signal power to there respective left or right brake/turn bulbs.

If you hold your foot on the brake pedal and wiggle the turn signal and or play with the hazard switch the brake lights will almost always intermittently start to work. this will confirm a bad turn signal switch which is pretty common on GM vehicle with this style setup.

Apr 05, 2013 | 1998 Chevrolet Lumina

1 Answer

2000 tacoma flashers don't work but turn sig do work!


The hazard switch gets power from the horn fuse which is hot all the time, and from the turn signal fuse which is hot when the key switch is on. The turn signal switch gets power from the hazard switch and both use the same flasher.
So if the turn signals work but the hazard switch does not power the lights, and both fuses have power, I would say the problem is inside the hazard switch.

Feb 19, 2013 | Cars & Trucks

1 Answer

The hazard lights buzz and don't work.


if fuse okay,could have faulty multifunction switch.

Nov 20, 2012 | 1997 Chevrolet Malibu

1 Answer

Hazard warning light don't work


Its possibe that ypou have independient FLASHER device, one for hazard and one for turn signal; check backside of fuse panel and replace it.

Aug 28, 2012 | 1993 Plymouth Voyager

2 Answers

2005 Ford Focus- Blinkers, Brake lights and hazards don't work -just change the bulbs and they still don't work. Help!


That should be on two different fuses, but everything goes thru the turn signal switch.
The switch might be faulty. A mechanic would check for voltage there.

Jul 11, 2012 | Ford Focus Cars & Trucks

1 Answer

Turn signal lights don't work even though hazards do


Sound like a flasher device go to bad; check in fuse box and replace it to solve this problem.

Jun 11, 2012 | 2006 Chrysler Town & Country

1 Answer

Hazard lights doesn't work


If the hazard lights and turn signal lights don't work then the problem will either be a blown fuse or the trafficator flash can is faulty.

Mar 30, 2012 | 1998 Nissan Sentra

1 Answer

1999 Lincoln Continental was in for repairs and now my turn signals and break lights dont work. Im being told it's something to do with the anti theft system because the battery was unhooked. The...


I suspect there is a problem with the turn signal/ hazard switch. turn the turn signal on left or right, if it doesn't flash, grip the hazard button and gently wiggle it around, if the signals start flashing, replace the turn signal switch. The Brake lights are wired through the turn signal switch, if the 3rd brake light works, the brake switch is OK. I don't think it has anything to do with the anti theft system (at this time)

Sep 21, 2011 | 1999 Lincoln Continental

Not finding what you are looking for?
2000 Chevrolet Malibu Logo

427 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...