Question about 2001 Chrysler PT Cruiser

Open Question

Error code p0401 on 2001 pt cruiser... common fix?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

motor1258
  • 6674 Answers

SOURCE: PT CRUISER 2002 AUTOMATIC DOESNT CHANGE TO GEAR 3

Take it in & have it scanned, may only be a faulty solenoid or even brake switch may cause code & symptoms. Sooner you get it in, the cheaper it will probably be to repair it

Posted on Sep 08, 2009

  • 10 Answers

SOURCE: DIAGNOSTIC code P01A4 for pt cruiser

my old amns cruiser has the same problem i'm putting it down to loss of turbo pressure as the inlet manifold is leaking when reved
i'll let you know when manifold is replaced if it cures it

Posted on Sep 09, 2009

lindsay836
  • 677 Answers

SOURCE: Errors P1684 given, how do I fix

The first code, p1684, just states the battery has been dis-connected in the last 50 start cycles.
Code p0401 is the EGR flow. You may need to replace the EGR valve.
Code p1193 is the intake air temperauture ( IAT) sensor. It may also need to be replaced.
Have your mechanic take a look at those, and please let me know how it goes.

Posted on Feb 11, 2010

  • 615 Answers

SOURCE: '05 PT Cruiser O2 sensor problems.

I had a similar problem with my car. It turned out the O2 sensors were fine and the issue was a leak in the throttle body causing the engine to run lean. If you have an ODB2 scanner you can look at fuel trims, etc and will be able to tell.

Posted on Mar 28, 2010

  • 5 Answers

SOURCE: 2001 PT Cruiser: How too remove crankshaft pulley 2001 PT Cruiser...

GET A 3 SPOKE PULLEY EXTRACTOR AND SCREW IN THE BOLT BUT IN THE CRANKSHAFT HOLE PUT A MUCH SMALLER SCEW SO YOU WOUNT MESS THE INSIDE UP

Posted on May 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I nave2 codes on a 2004 pt cruiser...1603 and 1604


these are PCM power or communication errors-

Read more at: http://www.obd-codes.com/forums/viewtopic.php?f=20&t=10580
Copyright © OBD-Codes.com

Feb 18, 2015 | 2004 Chrysler PT Cruiser

2 Answers

Was there a recall on pt dream cruisers due to overheating problems?


http://www.ptcruiserlinks.com/forum/general-pt-cruiser-discussions/43087-03-pt-non-turbo-overheating.html

Aug 10, 2014 | Chrysler PT Cruiser Cars & Trucks

1 Answer

ERROR CODES P0551 AND P1597


power stering sensor.speed control switch.

Mar 01, 2013 | 2001 Chrysler PT Cruiser

1 Answer

I have a 2004 pt cruiser. Each week it dies. Something to do with the oxygen sensor. Mechanic said I needed to have the computer reflashed? Any thoughts? Could this be the problem?


if you have replaced the sensor you will need to have the comp cleared some times the comp will hold the error code even though the part is new it will still read as faulty .a simple clearing of the codes should fix the problem.

May 17, 2012 | 2004 Chrysler PT Cruiser

1 Answer

How do I fix low suspenion


If you mean this common problem:
http://www.juhasuomela.com/pt-cruiser/kuvat/alatukivarrenpusla.jpg
Take the lower arm away and replace the rubber bush.

http://www.juhasuomela.com/pt-cruiser/kuvat/alatukivarsi.jpg

If you like drive more than 30,000 miles, you should use urethane bush:

http://www.juhasuomela.com/pt-cruiser/kuvat/uretaani.jpg

May 16, 2011 | 2002 Chrysler PT Cruiser

2 Answers

PO551 fault code on PT cruiser...power steering??


i would check the power steering fluid to make sure it isn't low. if that checks out then i would just keep an eye on it.

Jul 30, 2010 | 2003 Chrysler PT Cruiser

1 Answer

PT CRUISER 2002 AUTOMATIC DOESNT CHANGE TO GEAR 3


Take it in & have it scanned, may only be a faulty solenoid or even brake switch may cause code & symptoms. Sooner you get it in, the cheaper it will probably be to repair it

Sep 08, 2009 | 2002 Chrysler PT Cruiser

1 Answer

I have a 03 chy.pt cruiser with a code po44o


Error code P0440 =Evaporative Emission (EVAP) System. This site explains why & how fix the problem. http://www.obd-codes.com/p0440

Jun 25, 2009 | 2003 Chrysler PT Cruiser

Not finding what you are looking for?
2001 Chrysler PT Cruiser Logo

1,577 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...