Question about 1993 Acura Integra Hatchback

2 Answers

Rattling noise when r.p.m.'s are going down but when i press the clutch the rattling noise goes away it is not hard to shift in and out of gears just put a short shifter in yesterday but before that was no noise sounds like something is loose but checked under the car and was ok please help me

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Exhaust hitting short throw or you left heat shields lose

Posted on Nov 28, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If its a 5 speed i would say check ur throw out bearings on ur clutch.

Posted on Aug 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Grinding clutch


I'm a little confused on your description of the noise. If I understand you correctly It is making the noise when it shifts smoothly into gear but at the same time it makes a grinding noise ? It possibly can be synchronizers if the grooves on the inside of the synchronizers are worn bad enough to where the gear isn't slowing down enough causing a grind as the clutching teeth on the gear mesh with the synchrode and the shift collar.
If it is making noise in all gears except 4th you may have countershaft brgs failing. The power flow in 4th gear goes directly through the mainshaft and has a 1 to 1 ratio. All other gears the powerflow goes through the countershaft causing a load on the countershaft so if you have bearings failing in the countershaft you will hear noise in all gears but 4th.
i hope I understood you correctly .

Jan 18, 2014 | 2002 Subaru Forester

1 Answer

Geo tracker transmission


repace clutch assy BAD

May 19, 2013 | 1995 Geo Tracker

1 Answer

I have a 2000 s80 volvo transmission shifts fine but in park or nueteral it makes a rumbling noise goes away when put into gear. it did make a jolt and bang when i pulled out from the intersection thanks...


when you are sitting idle and you press the clutch without putting it into gear does the noise go? if so you will need to fit a new clutch kit.

Dec 13, 2009 | 2000 Volvo S80

1 Answer

Vibration through the car Transmission-motor Linkage?


Check to make sure both headlights are tight,,,when it rattles at idle go feel the headlight and hold it and see if the noise and vibration goes away,sometimes the headlight has too much clearance and causes a massive vibration,,if thats not it try...loosening all the motor mounts and rock the car back and forth and them retighten them,it reseetles the mounts and sometimes fixes the issue,,also check the lower engine and trans mounts for wear.

Oct 30, 2009 | Saturn SW2 Cars & Trucks

1 Answer

1999 honda prelude manual transmission isn't disengaging all the way when i shift, sometimes locking the shifter in gear or not allowing me to up or down shift. I know my master and slave cylinders need to...


This depends as dose it do it when cold or hot.
2nd when you push in pedal and put in gear dose it go in clean or hard to select 3rd can you hear a grinding noise when pushing in pedal and noise goes
when you take you foot off the clutch pedal IF so then its the thrust bearing on clutch REPLACE ALL .4th if you push in clutch pedal and select a gear and let the clutch out if drive right out (replace)

Sep 27, 2009 | 1999 Honda Prelude

1 Answer

Gearbox rattles at idle and in all gears. noise goes away when clutch pressed. anybody help? 1.3 gl swift 2006 model.


needs a throughout bearing. it is what presses the clutch in. thats why it goes away when you depress the penal. but it has to be removed with the clutch so while in there the clutch should be done. hopefully this helps you. good luck and please ask ant more question you have

Sep 24, 2009 | 2006 Suzuki Swift

1 Answer

Clutch rattle


this sounds like an adjustment issue. you did not mention the mileage...The clutch is released by a bearing, this release bearing needs to come back off of the fingers of the clutch pressure place, early wear and noise happens.

Near the end of the clutch life, you may find that you cannot release any more, if your model is adjustable.

Start with proper clutch release adjustment.

Doc

Sep 14, 2009 | 1998 Volkswagen Golf

1 Answer

Rattling noise


I have a 98 blazer that makes similar sounds but it's pieces of the dust shield off the rear wheel assembly that got down inside the brake rotor. Only happens when the truck is going forward

Dec 14, 2008 | 1995 Chevrolet Blazer

Not finding what you are looking for?
1993 Acura Integra Hatchback Logo

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...