Question about 1993 Nissan Sentra 4 Door

Open Question

Replace,front brake pads,1993 nissan sentra xr

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 90 Answers

SOURCE: brake light switch

HI
IT WAS LOCATE IN UPPER OF THE BRAKE PEDAL
BEFORE YOU CHANGE IT CHECK FOR :-

STOP LAMP SWITCH AND ASCD CANCEL SWITCH CLEARANCE
1. Twist and pull to remove switch.
2. Pull up on brake pedal pad and hold.
3. Insert switch into retainer until switch plunger is completely depressed.
4. Turn the switch until it locks into place in the brake pedal bracket.
NOTE:
When turning the switch to lock into place, the switch backs off the stopper to the correct clearance automatically.
5. Release the brake pedal pad.

ASK ME FOR MORE ??
WITH MY BEST WISHES

Posted on Jul 23, 2008

Ad
  • 2 Answers

SOURCE: 1999 nissan quest brake pad replacement

you have two bolts on in side of brake caliper undo the hole claipier should come away

Posted on Feb 02, 2009

  • 2 Answers

SOURCE: replace front brake pad 2003 toyota 4 runner

Diagram is unnecessry.
Pull both front wheels
Work one at a time leaving the other for reference
Find the retention spring ... its a paperclip thickness wire spring... dislodge center retention loop and undo from both ends which engage brake pad retention rods.
Pull the rods out
Pull the old pads out... laying everything on the ground
Use scrap wooden wedges to pry between the rotor and the caliper ...inside and out until the calipers are fully withdrawn. Use the new pads to measure if they are far enough back.
Note... the brake fluid will have dropped in the master cylinder over many months of wear... do not fill it. When the calipers are pushed back they will fill the reservoir again... one wheel at a time.
Be sure to identify the correct pad based on what you took out and what is on the other side (if you screwed up the layout)
Make sure to take the old antisqueek backing plate from the old pad and place it on the new pad. They don't use lubricant on these anymore.
Replace the pads... the retention rods... then the retention spring
Do the other side
Then progressively step on the brake peddle until full tension is felt
Check the master cylinder reservoir... probably needs no additional fluid.
New pads will register in existing ridges in each disc in no time at all.
You should check the discs to see if they need to be replaced during this operation...using some calipers

Posted on Mar 25, 2009

  • 3600 Answers

SOURCE: How do I change brake light bulb of Nissan Sentra 2008

the llight assembly has to be removed there are 4 screws to get it out with, however some just unscrew counter clockwise to get the bulb out.

Posted on Jun 21, 2009

  • 770 Answers

SOURCE: brake light, 2008 Nissan Sentra

Open the trunk and locate the trim door that covers the back of the drivers side tail light assembly. Open the door and locate the bulb holder. The bulb holder can be removed from the tail light assembly housing by turning counter clockwise 1/4 turn. Holding the bulb holder in one hand, press gently on the bulb and turn then bulb counter clockwise to remove. Replace with a combo bulb and reverse proceedure to re-install.

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced front pads on my 1999 Nissan Sentra. Brake pedal felt low.Had system flushed, bled and rear shoes adjusted. Still have low pedal and spongy feel. Suggestions?


have had this on different models and makes and what i do is to push brake pedal down and jam it down a length of wood or anything that holds the pedal down a bit not hard down -and leave overnight .if this fails then renew the master cylinder

Dec 03, 2016 | 1999 Nissan Sentra

1 Answer

While I am driving when I am pressing the gas pedal it makes a scraping noise but not all the time. If I hit the brakes it will stop. I have a 2001 Nissan Sentra GXE


Sounds like it might be the low brake pad indicator. A small flap of metal which is made to scrape the rotor when the brake pads reach a certain low level. When brackes are applied the noise typically quiets.
Check for worn front brake pads.

Jun 26, 2011 | 2001 Nissan Sentra

2 Answers

Got new tires got front end alinement got new


most likely been front damaged before or check out the wish bone or shock

Mar 31, 2010 | 2002 Nissan Sentra

2 Answers

My brake light in my 2001 Sentra SE came on. Any


either the park brake switch is stuck open or the master cylinder is low on brake fluid.

Jul 10, 2009 | 2000 Nissan Sentra

1 Answer

Whistling car


I had the same problem with my first car. It was the disc brakes rubbing steel to steel. You need to change your brake pads...right now!

May 23, 2009 | 2009 Nissan Sentra

1 Answer

Handbrake light stays on for a while


The Brake light usually also warns of low brake fluid in your brake master reservoir. Have you checked the level?

Apr 03, 2009 | 1993 Nissan Sentra 4 Door

1 Answer

Front brakes-2001 Nissan Sentra


You will need a jack and 2 jack stands to get the front wheels off the ground (break the lug nuts loose before lifting) and support the vehicle.

You will need the lug nut wrench (or a 1/2 inch breaker bar and 21 MM socket) to remove the wheel.

You will need a 14 MM wrench to remove the caliper bolts and possibly a flat head screwdriver to pry the caliper off of the pads if it is difficult.

You will need a big pair of channel lock pliers to compress the piston back into the caliper bore to allow room for the new pads.

You may need a hammer to hit the rotors to break them loose if they are rusted into place on the hub- a couple good shots should break them free if needed.

You will also need a wire brush and some good brake grease (available at any parts store). You will want to see any place that the pads contact a stationary surface and clean this area and apply a film of the grease to these points to prevent binding and uneven pad wear.

Hope this is helpful!!


Nissan Scope Technician- 10+ years experience in Nissan dealership.

Nov 16, 2008 | 2001 Nissan Sentra

1 Answer

Front spindles


ok... replace them....inspect the bearings and replace if necessary....
Robert
and have the cv joints inspected as well.

Sep 05, 2008 | 1991 Nissan Sentra 2 Door

Not finding what you are looking for?
1993 Nissan Sentra 4 Door Logo

Related Topics:

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...