Question about Chrysler Voyager

1 Answer

How do i remove my oil pan on a 2000 3.3l 6 cylinder voyager?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 651 Answers

Unbolt it.

Posted on May 20, 2011

  • wrestlnmania May 20, 2011

    i understand unbolt it i am not totally ignorant. It looks like there is some hidden up under some other parts of the car i was wondering if anyone with experience in doing it had the steps and any tips.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the oil send unit on a 1991 Chevy S10 6 cylinder 4.3L?


The oil sending unit for this vehicle is located on the bottom of the engine inside of the oil pan area. The oil pan will have to be removed to access it.

Nov 28, 2016 | 1991 Chevrolet S-10

Tip

Changing oil pan gasket


Plymouth Voyager 3.0L Oil Pan

On the bottom the the motor you will find 2 brackets connected to the motor by the transmission loosen off the motor mount bolt ( you don't have to take it off )
undo the bolts holding the brackets to the block of the motor once that is done you can now move the brackets just enough to allow full access to the oil pan access then one by one remove the oil pan bolts which should be a 10mm scocket

on Sep 07, 2011 | 1996 Plymouth Voyager

1 Answer

How do I remove oil pan on a 2001 gmc Sonoma pick up truck to replace gasket


1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN ...

? 2:31
https://www.youtube.com/watch?v=1KsRTlnW7Cg
Sep 27, 2011 - Uploaded by JohnSmiths8379858
trying to reomove the oil pan to this truck has been sitting for about 6 ... 1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN REMOVAL "HELP!

Oil Pan Gasket: How to Change Oil Pan Gasket for 2001 ...

www.2carpros.com/questions/2001-gmc-sonoma-oil-pan-gasket
Mar 18, 2011 - How to change oil pan gasket for 2001 sonoma, can i get away with just raising the engine two inches to ... 2001 GMC Sonoma • 4 cylinder 2WD Automatic • 150,000 miles ... You need to remove the engine to get the sump off.

Nov 28, 2015 | GMC Cars & Trucks

1 Answer

How do you drain the oil from the auto box on a 3.3 voyager,there doesnt seem to be a visable drain plug?


You take off the bottom pan to drain it. Loosen the bolts all around and begin loosening more at one end, so pan begins lowering from one end, and you have a good large, deep catch pan to catch the fluid. Let it drain that way till all drained, then remove the pan and empty its contents into your catch pan. Expect 6-8 quarts to drain, I believe.

Jan 13, 2013 | 2000 Chrysler Grand Voyager

1 Answer

How to change oil pan gasket for 2005 dodge caravan


Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004

Oil Pan - Removal & Installation

2.4L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Structural collar A/C compressor bracket to oil pan bolt Oil pan
  4. Clean the oil pan and all gasket mating surfaces.
To install:
  1. Install or connect the following:
    Oil pan gasket to the block after applying engine RTV at the oil pump parting line Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Structural collar Negative battery cable
  2. Fill the crankcase to the correct level.
  3. Start the engine, check for leaks and repair if necessary.

3.0L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Starter motor Front motor mount bracket Bending braces Torque converter dust shield Oil pan

    e6c7cfd.jpg
    Fig. Oil pan mounting bolt tightening sequence-3.0L engine

To install:
  1. Clean the oil pan all mating surfaces.
  2. Apply RTV gasket material to the oil pan.
  3. Install or connect the following:
    Oil pan. Tighten the bolts in sequence to 50 inch lbs. (6 Nm). Torque converter dust shield Bending braces Front motor mount bracket Starter motor Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

3.3L & 3.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Engine oil dipstick Drive belt splash shield Strut to transaxle attaching bolt and loosen the strut to engine attaching bolts Transaxle case cover Oil pan fasteners Oil pan and gasket

To install:
  1. Clean the oil pan and all mating surfaces.
  2. Apply a 1 / 8 inch bead of gasket material at the parting line of the chain case cover and the real seal retainer.
  3. Install or connect the following:
    New gasket on the oil pan Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Transaxle case cover All bending brace bolts Drive belt splash shield Engine oil dipstick Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

Hope helps (remember rated this).

Jun 24, 2010 | 2005 Dodge Caravan

1 Answer

How to change oil pump on plymouth grand voyager


go to http://www.autozone.com/autozone/homePage.jsp and sign up, put in your vehicles info and click on repair guides, they have oil pan remove and replace but no guide for the oil pump but its located in the oil pan and usually held on with 2 bolts and a gasket inside the pan, Tough job probably need someone with mechanical experience to help with this.

Apr 18, 2010 | 1997 Plymouth Grand Voyager

1 Answer

Need to know how to change the oil on a 2008 Hyundai sonata, how many quarts does it need.


ALMOST every car I've worked on has a drain plug on the "oil pan" ..big,.. usually stamped pan on bottom of motor to release used oil .. 1.drain oil 2.reinstall plug
3.remove and replace filter 4. refill with oil.. (my rule of thumb is 4 qts. for 4 cylinder 5 qts' for 6-8 cylinder) you failed to mention 4 or 6 cylinder (your car came with both)

Feb 20, 2010 | 2008 Hyundai Sonata

1 Answer

How to remove oil pan from 2003 kia spectra


REMOVAL

1. Disconnect negative battery cable.
2. Drain engine oil
3. Remove LH and RH side splash shields.
4. Remove front exhaust pipe.
5. Remove oil pan mounting bolts.
  1. Remove oil pan with screwdriver or suitable tool as shown in figure. Caution:
a) Do not force tools between cylinder block and oil pan because this may damage sealing surfaces. b) Do not damage sealing surfaces when removing old sealant

  1. Remove oil strainer.

Replacement

Caution:
a) If oil pan is reused, remove all foreign material from sealing surfaces of cylinder block and oil pan. b) If bolts are reused, remove old sealant from bolt threads.


  1. Install oil strainer. Tightening torque: 5.8 - 8.7 ft. lbs. (7.8 - 11.8 Nm, 0.8 - 1.2 kg-m)
  2. Apply a continuous bead of silicone sealant to baffle plate along inside of bolt holes on contact surfaces. Caution: The oil pan must be installed no longer than 5 minutes after silicone sealant is applied.
3. Install oil pan. Tightening torque: (A) (B) (C) (D): 5.8 - 8.0 ft. lbs. (7.8 - 10.8 Nm, 0.8 - 1.1 kg-m) (E): 28 - 38 ft. lbs. (38 - 51 Nm, 3.8 - 5.3 kg-m)

4. install front exhaust pipe. Tightening torque: (A): 29.7 - 40.5 ft. lbs. (40.2 - 54.9 Nm, 4.1 - 5.6 kg-m) (B): 51 - 69 ft. lbs. (69 - 94 Nm, 6.9 - 9.4 kg-m) (C): 15.2 - 20.2 ft. lbs. (20.6 - 27.4 Nm, 2.1 - 2.8 kg-m)

5. Install LH and RH side splash shields. Tightening torque: 12 - 18 ft. lbs. (16 - 24 Nm, 1.6 - 2.4 kg-m)
6 . Fill with specified amount and type of engine oil.

GOOD LUCK,I HOPE THIS HELPS...

Jun 04, 2009 | 2003 Kia Spectra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8547 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...