Question about 2006 Jeep Liberty

1 Answer

Heater motor control switch only works on #4 position

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 202 Answers

Your resistor is bad. You need to buy it and find it on the inside of the firewall directly behind the heater ac controls.

Posted on May 20, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need pitcure of vaccum lines on 1999 Ford Ranger v6 3.o air and heat blows only threw the defroster.


26392097-cvaukpwazi2vnl4fgradjhua-2-2.gif

Item Part Number Description 1 18A318 Vacuum Control Motor-, Panel/Defrost Door 2 18A478 Panel/Defrost Door (Full Vacuum Position) 3 - Defrost Air Flow 4 - Side Window Demister Air Flow 5 18B545 Temperature Blend Door (Full Heat Position) 6 19860 A/C Evaporator Core 7 19A813 Air Inlet Duct Door (Full Vacuum Position) 8 - Outside Air Inlet 9 18A318 Vacuum Control Motor-, Air Inlet Duct Door 10 - Recirculated Air Inlet 11 18527 Blower Motor 12 19A566 A/C Vacuum Reservoir Tank and Bracket 13 - Vacuum from the Engine Intake Manifold 14 19B888 A/C-Heater Function Selector Switch 15 - Vacuum to the 4x4 Hub Solenoids 16 18495 Water Diverter Valve (Full Vacuum Position) 17 18476 Heater Core 18 18A559 Floor/Panel Door (Full Vacuum Position) 19 - Floor Air Flow 20 18A318 Vacuum Control Motor-, Floor/Panel Door 21 - Panel Vent Air Flow

Dec 09, 2016 | Ford Ranger Cars & Trucks

1 Answer

My 1998 gmc jimmy slt has a heating problem. The heater wont turn off. As long as the car is on the heater is on full blast. The fans work and everything knob wise works but the heater is always on.


The air temperature valve electronic actuator positions the temperature door according to the temperature setting of the temperature control on the temperature control knob. For the full COLD temperature setting, the temperature control returns approximately 12 volts to the air temperature valve electric actuator. When the temperature setting is changed to full HOT, the temperature door is moved to the warm position and the output drops to about 0 volts. For a temperature setting in the mid range, the temperature door is positioned according to the voltage supplied through the temperature control switch.
Temperature Control Inoperative

2

Inspect the HVAC I fuse 21.
Is the fuse open?
--
Go to Step 20
Go to Step 3

3

  1. Disconnect the air temperature valve sensor.
  2. Turn the ignition switch to the RUN position.
  3. Move the headlamp switch to the PARK position.
  4. Using the J 35616-A , connect a J 39200 Digital Multimeter (DMM) between cavity 8 (CKT 733) of the air temperature valve motor connector and ground.
  5. Move the temperature control knob from the HOT position to the COLD position.
Does the voltage vary smoothly and continuously within the specified range?
0-12 V
Go to Step 4
Go to Step 9

4

Using the J 35616-A , connect a J 39200 DMM between cavity 10 (CKT 341) of the air temperature valve motor connector and ground.
Does the voltage equal the specified value?
B+
Go to Step 5
Go to Step 7

5

Using the J 35616-A , connect a J 39200 DMM between cavity 10 (CKT 341) and cavity 7 (CKT 1850) of the air temperature valve motor connector.
Does the voltage equal the specified value?
B+
Go to Step 6
Go to Step 8

6

Replace the air temperature valve motor.

Aug 31, 2015 | GMC Cars & Trucks

1 Answer

Why wont my 2001 ford windstar blow out of vents ? only on defrost?


Air Flow Control
Air flow control is accomplished in the following manner:
  • Primary control is through the function selector knob , mounted on the heater function selector switch, which is part of the heater control .
  • The function selector knob has the following positions: OFF, PANEL, PANEL/FLOOR, FLOOR, FLOOR/DEFROST and DEFROST.
  • The heater function selector switch combines a vacuum selector valve with an internal electrical switch.
  • The vacuum selector valve directs source vacuum to various vacuum control motors (18A318) . Refer to the System Airflow Schematic and Vacuum Control Charts.
  • An internal single-pole electrical switch is also controlled by the selector. The switch controls the electrical supply to the heater blower motor switch (18578) .
  • The position of the function selector knob determines the manner in which the system will operate.
  • Each position of the function selector knob is detented for positive engagement.
  • You probably have a vacuum leak , Pull heater control panel an check for vacuum . A broke vacuum hose or The vacuum selector valve is bad ! Or check for a vacuum hose in the engine compartment being off somewhere !

Mar 08, 2015 | 2001 Ford Windstar

1 Answer

1997 Ford Taurus front defrost not working


. Air won't blow out of the floor or center vents just defrost ? Do you have manual or automatic climate control ?
Air Flow Control
Air flow control is accomplished in the following manner:
  • Primary control is through the function selector knob mounted on the A/C-heater function selector switch, which is part of the integrated control panel.
  • The function selector knob has the following positions: OFF, MAX A/C, A/C, PANEL, PANEL/FLOOR, FLOOR, FLOOR/DEFROST and DEFROST. The A/C-heater function selector switch combines a vacuum selector valve with an internal electrical switch.
  • The vacuum selector valve directs source vacuum to various vacuum control motors (18A318). Refer to the Vacuum Control Diagram , System Airflow Schematics and Vacuum Control Chart .
  • Two internal, single-pole electrical switches are also controlled by the A/C-heater function selector switch. The combination of these electrical switches controls the electrical supply to the A/C clutch and heater blower motor switch (18578).
  • The position of the function selector knob determines the manner in which the system will operate.
  • Each position of the function selector knob is detented for positive engagement.
  • Vacuum Control Motors The vacuum control motors (18A318):
    • are located on the A/C evaporator housing, A/C recirculation air duct and heater air plenum chamber (18471).
    • direct system airflow to the vehicle interior as determined by the remote climate control module or manual override.
    • The five-passenger seating configuration has an additional vacuum control motor mounted on the heater air plenum chamber to control airflow to the rear seat A/C register (19893).


vacuum control motor-i4bq0ig33y1522pr2d2rrkk3-2-0.gif

Jul 09, 2017 | Ford Cars & Trucks

1 Answer

Heater motor control switch only works on #4 position


The resistor board is bad,it controls the different speeds of the blower.

May 19, 2011 | 2006 Jeep Liberty

5 Answers

My 1997 ford f150 heater will not blow hot air. i have replace the switch that controls the hot and cold air. i do not know what else to do. i do not heat any vacuum noise when i switch it to the heater or...


first, check under te hood to see if the heater core water hoses are hot going in and coming out. If hot going in but cold coming out, water valve (if you have one) may not be working.
------------------------------------------------------------------------------------------------
Control System Outputs
The air management doors are controlled by vacuum control motors (18A318) and an A/C electronic door actuator motor (19E616). The air inlet and distribution doors are controlled by vacuum control motors. The temperature blend door is controlled by the A/C electronic door actuator motor.
The A/C electronic door actuator motor provides a variable number of temperature blend door positions. Temperature control position energizes the A/C electronic door actuator motor moving the temperature blend door.
Vacuum control motors are used on both air distribution and air inlet doors. The air inlet and panel/defrost doors use a two position vacuum control motor. The floor duct/panel door uses a three position vacuum control motor. Vacuum control motors are controlled by engine vacuum through the climate control head.
For more information on the control components Section 412-04 .
-------------------------------------------------------------------------------------------------------------------------------------
Air Management Doors
The air management doors are controlled by vacuum control motors (18A318) and an A/C electronic door actuator motor (19E616). The air inlet and distribution doors are controlled by a vacuum control motor. The temperature blend door is controlled by the A/C electronic door actuator motor.
The A/C electronic door actuator motor provides a variable number of temperature blend door positions. Temperature control position energizes the A/C electronic door actuator motor moving the temperature blend door.
Vacuum control motors are used on both air distribution and air inlet doors. The air inlet and panel/defrost doors use a two position vacuum control motor. The floor duct/panel door uses a three position vacuum control motor. Vacuum control motors are controlled by engine vacuum through the climate control head.
-------------------------------------------------------------------------------------------------------------------
Section 412-04: Control Components - Climate Control 1997 F-150, F-250 Workshop Manual
REMOVAL AND INSTALLATION A/C Electronic Actuator
Removal
  1. Remove the floor duct panel.
    • Remove the two plastic push pins (one each side) and release the expander clip.
  1. Remove the RH instrument panel brace.
    1. Remove the lower nut.
    1. Remove the upper bolt.
    1. Remove the brace.
  1. Remove the LH instrument panel lower nut and position brace out of the way.
  1. Disconnect the vacuum harness from the vacuum actuator.
  1. Remove the floor duct.
    1. Remove the two screws (one each side).
    1. Remove the floor duct.
  1. Remove the panel/floor door vacuum control motor.
    1. Disconnect the vacuum line connector.
    1. Remove the two panel/floor door vacuum control motor screws.
    1. Slide the rod out of the door and remove the panel/floor door vacuum control motor.
  1. Remove the electronic actuator.
    1. Disconnect the electrical connector.
    1. Remove the three screws.
    1. Pull down to release the actuator shaft and remove the electronic actuator.

Jan 24, 2011 | 1997 Ford F150 Regular Cab

2 Answers

2001 Jeep Wrangler heater blower stopped working


Yes I would go with the switch, BUT, does it have a resistor bank? That is, how does it reduce the speed? Many systems use resistors to lower the speed. Burnt or bad connections can cause this as well.
You can test the blower motor by connecting direct power from a source like the cigarette lighter if you are handy.
Most of the time the lower speeds konk out but the high speed continues to work this is the resistor bank that goes out.

Mar 25, 2010 | 2001 Jeep Wrangler

1 Answer

Ford explorer heater fan not working


If this occurs in all positions, check fuse, check for power at the fan motor, if power in all positions replace motor. if no power at fan and fuse is good, check blower motor resistor and blower motor control switch. Replace as required

Oct 10, 2009 | 1999 Ford Explorer

1 Answer

Aircondition blows hot air on normal but blows cold air on max


The temp blend door rotates between allowing heat through the heater core, or cold air through the a/cevaporator, or a blending of the 2 by being anywhere between the two.

I would check the heater a/c control head first and hope it's just the control head.
----------------
here is a descripton of the system.

Section 12-03A: Air Conditioning, Heater System, Manual, Ranger and Explorer 1996 Ranger and Explorer Workshop Manual
DESCRIPTION AND OPERATION A/C-Heater System, Manual The manual air conditioning/heater system used in these vehicles is a split-case, blend air design. This design includes the following major components:
  • An A/C evaporator housing (19850) which is attached to the engine compartment side of the dash panel (01610). This assembly includes: (1) the A/C evaporator core (19860), (2) the suction accumulator/drier (19C836), (3) the A/C cycling switch (19E561), (4) an internal, A/C evaporator core orifice (19D990) located inside the inlet line to the A/C evaporator core, (5) a blower motor (18527), (6) a blower motor wheel (18504), (7) a heater blower motor switch resistor (18591), and (8) the A/C evaporator case (19897).
  • A heater air plenum chamber (18471) which attaches to the passenger compartment side of the dash panel. This assembly includes: (1) the outside/recirculating air inlet door, (2) the panel door, (3) the floor defrost door, (4) the temperature blend door, and (5) the heater core (18476).
  • Other components which link and/or control the heating and air conditioning systems include: (1) the A/C control (19980), (2) the ducts and registers, (3) the windshield defroster hose nozzle (18490), (4) the control cables, (5) the vacuum lines, (6) the refrigerant tubes and hoses, (7) the A/C compressor (19703), and (8) the A/C condenser core (19712).
050240f.gif
The A/C control (19980) assembly consists of three main parts:
  • The function selector knob, a vacuum selector valve combined with an internal electrical switch.
  • Heater blower motor switch (18578), an electrical switch that provides four speeds of A/C blower motor operation.
  • A temperature control knob, which controls the position of the temperature blend door mounted on A/C evaporator housing (19850) assembly.
---------------------------
Temperature Control
The temperature selector actuates a variable resistance switch. This switch varies the voltage to an electric actuator used to position the temperature blend door. Positioning the temperature control in any position between COOL and WARM causes the temperature blend door to direct more or less outside air through or around the heater core (18476) for whatever proportion of heated or unheated outside air is desired. The air blends together as it leaves the heater core and enters the heater air plenum chamber (18471) for distribution.
---------------------------
System Airflow Description Air is drawn into the system by the blower motor (18527) through the outside-recirc. door opening. The air is blown through the A/C evaporator core (19860) and then the heater core (18476) (when the temperature control is moved toward the WARM position). When the temperature blend door is in the maximum COOL position, the air bypasses the heater core. When the temperature control is moved to the right, away from the maximum COOL position, air passes through the heater core where it is warmed, and then mixed with the cool air before it is discharged through the registers. OFF
With the function selector in the OFF position, the outside-recirc. door is in the recirculated air position. It is closed to outside air and no air passes through the system. The blower motor is off. MAX A/C
NOTE: No temperature modulation is possible in the MAX A/C position.

In the MAX A/C position, the outside-recirc. air door is in the recirculated air position. All of the air discharges through the panel registers except for a small amount of floor bleed. The A/C compressor (19703) operates in this function control setting.
--------------------------------
You have to almost remove the dash to get this part out.
Removal
  1. Disconnect battery ground cable.
  1. NOTE: Refer to Section 01-12 for instrument panel removal and installation procedure.

    Loosen instrument panel (04320) and pull back from cowl.
  1. Remove A/C electronic door actuator motor electrical connector from bracket on A/C evaporator housing.
  1. Remove three A/C electronic door actuator motor retaining screws.
  1. NOTE: The mounting bracket remains in place on the A/C evaporator housing.

    Lift A/C electronic door actuator motor vertically approximately 12mm (1/2 inch) to disengage it from bracket and actuator shaft, then pull A/C electronic door actuator motor back toward passenger compartment.
82a7359.gif

Apr 25, 2009 | 1996 Ford Explorer

1 Answer

I have the same problem with my windstar blower is fine but is coming cold air but no heat i dont know what to do can any one show me how to fix it thnx


First, feel the heater hoses going into the firewall under the hood. If they are hot, then you have hot engine coolant going into the heater core. If they are not hot, then you either have a bad thermostat or you are very low on engine coolant.

Next you need air flowing through the heater core so it can come out heated through your vents. If the iar is flowing somewhere else, your temp blend door is not moving because the bend door motor is bad or your temp knob on your heater controls is bad. The blend door motor is an electric motor.

------------------------------------------------
Air Flow Control
Air flow control is accomplished in the following manner:
  • Primary control is through the function selector knob , mounted on the heater function selector switch, which is part of the heater control .
  • The function selector knob has the following positions: OFF, PANEL, PANEL/FLOOR, FLOOR, FLOOR/DEFROST and DEFROST.
  • The heater function selector switch combines a vacuum selector valve with an internal electrical switch.
  • The vacuum selector valve directs source vacuum to various vacuum control motors (18A318) . Refer to the System Airflow Schematic and Vacuum Control Charts.
  • An internal single-pole electrical switch is also controlled by the selector. The switch controls the electrical supply to the heater blower motor switch (18578) .
  • The position of the function selector knob determines the manner in which the system will operate.
  • Each position of the function selector knob is detented for positive engagement.
Temperature Control
The temperature control operates in the following manner:
  • Temperature control of the heater system is determined by the position of the temperature control knob (between COOL-BLUE and WARM-RED) of the heater control .
  • This control knob is connected to a potentiometer mounted in the heater control . This potentiometer is electrically connected to the electric blend door actuator that operates the A/C air temperature control door.


e72a310.gif

  • Movement of the control knob from COOL (Blue) to WARM (Red) causes a corresponding movement on the air temperature control door and determines the temperature that the system will maintain.
System uses a reheat method to provide conditioned air to the passenger compartment.
  • All airflow from the blower motor (18527) passes through the A/C evaporator housing .
  • Temperature is then regulated by reheating a portion of the air and blending it with the remaining cool air to the desired temperature.
  • Temperature blending is varied by the air temperature control door, which regulates the amount of air that flows through and/or around the heater core (18476) , where it is then mixed and distributed.
--------------------------------------------------------------------------------------------------------------------------
inside you plenum box:

09f3f8a.gif

Mar 03, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
2006 Jeep Liberty Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...