Question about Hyundai Accent

2 Answers

Removal drivers rear side window from a 2000 3 door model

Posted by on

  • 1 more comment 
  • matty01589 May 20, 2011

    hyundai accent year 2000

  • matty01589 May 20, 2011

    3 door 1.3 model

  • matty01589 May 20, 2011

    its a 3 door hatch back no rear door the window is behind the drivers door

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyundai Master
  • 76,164 Answers

Hello
Please clarify the model of Hyundai you have. Keep in mind we have information on USA models only. Thanks

Posted on May 20, 2011

  • yadayada
    yadayada May 22, 2011

    Replacing this window requires a special tool called a hot wire window adhesive cutter and special skills, by the time you buy the tool you can have the window replaced by a glass shop for about the same price.

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,530 Answers

Welcome to Fixya

May i know the exact Brand and Year model of the vehicle? This will help me in giving you exact instructions.

Thanks

Posted on May 20, 2011

  • Jose Cada
    Jose Cada May 20, 2011

    First take out all of the screws in the door panel. There is one in the handle that opens the door, and 2 in the door panel handle. Use the flat screwdriver to pop off the covers. Taking out the door handle is a little tricky. Slide it towards the front of the car and pull out. You might not get it the first try. Once you get the handle out enough, you will be able to see 2 metal rods connecting to it(towards the back of the car). Using the standard screwdriver, pull the plastic piece(either blue or red) towards you and it should unclip from the rod. Next, pick up on the rods and they should come out of the handle. Once all screws and the door handle are removed, you can take off the panel.

    To remove the door panel, simply pull it off, starting at the bottom of the door and prying your fingers between the panel and the door. You will hear a series of pops. You didn't break anything. If it doesn't come fairly easy, don't pull too hard. You may have missed a screw. Once the panel swings freely on the window slot, get it close to the door and pick up, as the top rests in the window slot. If you have power windows, you will have to unclip the wires going to the switch. Once the panel is off, drop the window and remove the 2 phillips screws holding the window on the track.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 grand marquis, only the two rear, electric windows don't work, is there something in common to cause this problem ?


One place to check would be to remove the trim from the lower part of the B-pillar (the part between the front and back doors, where the rear door hinges are) on the driver side. There should be a plug near the floor connecting the wiring from the main power window switch on the driver's door to the two rear doors.

Oct 03, 2016 | 2000 Mercury Grand Marquis

5 Answers

I need to know how to replace the driver side rear window.


You dont tell us excalty the year of your CRV, so keep in mind that this is the procedure for 2000 Honda Truck CR-V 4WD 2.0L MFI DOHC 4cyl, other year is similar process. If you need take off the window, you need take off the "window regulator", so check this...


Honda CRV/Odyssey 1995-2000 Repair Information

Door Glass and Regulator

REMOVAL & INSTALLATION CRV Models and 4-Cylinder Odyssey Models
(see Figures 1, 2, 3 and 4 )


0d90b2a.jpg
Fig. 1: Always matchmark any fasteners that are mounted through a slotted hole. This bolt is used to adjust the window position

e3eb553.jpg

Fig. 2: The window is raised just enough to access the mounting bolts

5abd45a.jpg

Fig. 3: Once the window fasteners are loosened, the window can be tilted and lifted out of the door

001509f.jpg

Fig. 4: Slide the window motor/regulator assembly out of the door
  1. Remove the door panel, as outlined in this section.
  2. Remove the plastic vapor barrier.
  3. On 4-cylinder Odyssey models rear door glass, remove the center rear channel bolt and remove the channel.
  4. Carefully raise the door glass until the bolts are visible.
  5. On 4-cylinder Odyssey models rear door glass perform the following:
    1. Remove the self-tapping screws from the outer triangular trim cover and remove the cover.
    2. Remove the door glass bolts.
    3. Carefully lower the glass, then remove the bolts and nut from the rear lower guide channel.
    4. Remove the glass from the rear guide channel.
    5. Apply protective tape around the painted surfaces of the window sash trim.
    6. Tilt the window forward and remove from the window slot.
  6. Loosen the bolts, then slide the lower guide forward and remove the window from the guide.
  7. Carefully pull the glass out through the window slot. Take care to not drop the glass.
  8. To remove the regulator, perform the following:
    1. Scribe a line around the rear roller guide bolt to mark its original position.
    2. Disconnect the electrical connector and harness clip, then remove the regulator mounting bolts.
    3. Remove the regulator through the hole in the door.
  9. Installation is in reverse order of removal. Apply grease to the rollers, guides and sliding surfaces of the regulator. Make sure to install the roller guide with the rectangular hole facing rearward. Check the window operation before installing the door panel and adjust if necessary.

Hope helps.

Jun 12, 2010 | Honda CR-V Cars & Trucks

1 Answer

Hi there ..I just got a driver side window motor,to replace my old one in my 99 Chevy Malibu..whats the steps to take to take off the old one and place the new ??


GM Malibu/Cutlass 1997-2000 - Repair Guide

Window Regulator And Motor Assembly
REMOVAL & INSTALLATION

Rear Door


4f4e997.gif
Fig. The rear window regulator is an assembly that consists of two pieces

NOTE The front window regulator is removed as an assembly with the door control module. Refer to the procedure outlined in this section under Door Locks.
  1. Remove the door panel and the water deflector.
  2. Remove the door glass (window).
  3. Detach the electrical connector, if equipped, or remove the window regulator handle.

To install:
  1. Install the window regulator.
  2. Place the regulator through the rear access hole into the door.
  3. Attach the electrical connector, if equipped, or install the window regulator handle.
  4. Install the rear side door window.
  5. Replace the door window assembly.
  6. Install the water deflector and the door panel.

Door Locks
REMOVAL & INSTALLATION

Door Control Module


882bea7.gif
Fig. The door control module contains the door locking system module and the power window system module
  1. Raise the window to the full up position.
  2. Remove the inside door trim panel. Refer to procedure outlined in this section.
  3. Pull off the plastic film water deflector enough to access the lock actuator.
  4. Remove the screws securing the door lock actuator.
  5. Remove the door locking system module nuts and bolt.
  6. Remove the door locking system module from the door.
To install:
Installation is the reverse of removal, but make sure to tighten the fasteners to the torque specifications listed:
  1. Door locking system module bolt-89 inch lbs. (10 Nm).
  2. Door locking system module nuts-89 inch lbs. (10 Nm).
  3. Door lock actuator screws-53 inch lbs. (6 Nm).

Hope helps (remember rated this) Good luck.

Jan 21, 2010 | 1999 Chevrolet Malibu

1 Answer

How do I remove the drivers side glass from a 2000 s10 extended cab truck


Remove inside door handles and trim, wind the window down untill you can see the securing bolts that afix the window to the mechanism, remove external weather strip, tilt the glass and remove going outside of the door frame {you may need to remove a bolt that holds the guide near rear of door} assembly is in reverse, lubricate guides and mechanism while your there. Remember we are here to help as best we can, good luck

Dec 17, 2009 | 2000 Chevrolet S-10

1 Answer

How do fix drver side rear sliding door window


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Pull back the weather seal and you'll see the innards of the door

Sep 21, 2009 | 2000 Mazda MPV

1 Answer

How to remove the drivers side and drivers side rear door panel. with power door locks and windows 2000 toyota corolla ce


Very simple!

Simply remove any exposed screws, and, using a tool from any automotive store (looks like a flattened out screwdriver with a slot on the end), and use it to pop the panel off. Remember to remove any wire connectors to the switches. Same for the rear. Installation in revers order......sounds harder than it is but it is really easy.

Take your time and take pics with a digital camera....too many pictures after each step is better than not enough!

Jun 24, 2009 | 2000 Toyota Corolla

1 Answer

Rear Window- Drivers side- won't work


Removal and Installation
  1. Remove the rear door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the watershield.
  1. Remove the interior weatherstrip.
  1. Remove the exterior-weatherstrip.
  1. Remove the nut and the rear window stabilizer.
  1. syh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removing the rivet center pins, place suitable support between the door outer panel and the glass to stabilize the glass.
    NOTE: Lower the window to access the rivets.
    Remove the two rivets retaining the rear door window glass to the rear door window glass run and bracket.
9eaea6b.gif
  1. Remove the rear door window glass.
  1. To install, reverse the removal procedure.

Apr 09, 2009 | 2000 Ford Taurus

1 Answer

Removal of rear door panel to access power window motor


SECTION 501-05: Interior Trim and Ornamentation 2000 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Rear Door Trim Panel Removal and Installation
  1. Remove the rear door trim panel screws.
  1. NOTE: The rear door trim panel has eight two-part pin-type retainers. The male part of the retainer will remain with the trim panel and the female part will remain with the door.
    NOTE: To release the door trim panel pin-type retainers, first pull outward on the bottom of the door trim panel.
    Remove the rear door trim panel.
    • Disconnect the window regulator control switch electrical connector.
  1. To install, reverse the removal procedure.

Apr 07, 2009 | 2000 Ford Taurus

2 Answers

There is a water leak somewhere in my 98 toyota camry that leaks into my passenger side floor. There is no sun roof and no visible leaks from the windows or doors. Any thoughts? A/C leak maybe? water...


I am the original owner of camry xle 1998 with wet floors. In 2000 I had drivers side door seal leaking at welt. Removed old door seal and new weather strip on drivers side installed. The door panel was never wet, but wet at bottom of door where there are drain holes...slowly leaking under carpet.
In 2001 later water again. Coming from overflowing A/C evaporator-drain plugged/ tank full of debris. Removed evaporator, cleaned + drain cleaned.
In 2003, driver door seal against window rotted. Removed door panel and found leak at window belt molding at the mirror joint inside + out. Lots of mold under carpet needed to replace! Made a fuss at dealers for reacurring problem and they replaced the carpet for free.

Sep 07, 2008 | 1999 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...