Question about Chrysler Sebring

1 Answer

Car is not turning over we sprayed either and did not work

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 29 Answers

If it has compression and an ignition source ( Ether) Than it has no spark, To Test This at night time, pull a spark plug, attach the Sparkplug wire to it, put the spark plug near a metal object and have somebody turn the vehicle over, if you dont see a small blue spark than either the distributor, distributor cap, rotor,coils or wires are gone.

Posted on May 20, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Windshield Solvent doesn't spray.Wipers work. I can blow air thru lines.But no spray..any suggestions? 1995 Chevy Luminia

Does the pump motor run when turn windshield spray?
Might be home in line.
Might be wrong fluid(too thick)
Might be wiper fluid motor broken.

Nov 03, 2016 | Cars & Trucks

1 Answer

My key wont turn on my 89 maxima

Try penitrating spray into barrel(key in)try turning key while spraying if it don`t work lock!!!!

Jan 06, 2013 | 1995 Nissan Maxima

1 Answer

Wouldn't start. Turned ignition switch. Nothing happened. Interior lights & headlights worked.tried 2 hours later & car started.

Does your security light flash if you turn your key to the 'on' position? If so, this is a Passlock problem. It should restart after 10 minutes. Here`s a possible solution that has worked for me. Have a new key cut from origional key or best condition key you have. Buy some Electronic cleaner and spray lots into the lock cylinder. Then, put your key in the ignition and turn from off to on position several times (5 to 10 times quickly). Then remove your key and spray again and repeat key turning. Do this several times. I don`t recomend any spray that is oil based. I no longer have issues with my Passlock system and I have almost 500 000Kms on my Impala.

Jul 03, 2010 | 2002 Chevrolet Impala

1 Answer

Trunck lock want turn to open

your going to have to spray with wd40 let it soak a minute then work the key in the lock and continue to spray once in a while ,until it turns , but keep working the key. hope this helps.

Feb 04, 2010 | 2001 Plymouth Neon

1 Answer

I put the key in the ignition and I try to turn it to start the car and it doesnt move.I have alresgy sprayed de-icer in it also I have sprayed sillico spray to try to loosen the cyclinder still nothing...

First, check to see if you have a different key that you also use for that car & try it. Second, you may need to remove the pressure off of the steering wheel to get the key to turn. Try turning the wheel even though it is locked to either side while attempting to turn the key. If that fails to work, it is entirely possible that your ignition switch or the lock cylinder will need to be replaced. Good luck.

Jan 29, 2010 | 2000 Chrysler Cirrus

1 Answer

Sometimes car won't start after driving. Can start it by spraying carborator cleaner in where air cleaner is. Replaced fuel regulator, didn't help. Doesn't do it all of the time, but want it fixed. If it...

Try cleaning the IAC valve locate near the air cleaner intake hole . Remove the aircleaner duct work. And when the car does start. Run engine at 1200 rpms or so. Spray carb cleaner inside the hole to the sides of the walls. you can see 2 small holes to the side of the walls. That is the IAC. Turn engine off ,let the cleaner soak in. Then restart the engine and spray some more. when I say spray , I mean a good 10 seconds of spraying right at the little holes . See if your car starts running better. if this does not work, replace the IAC it is on the outside of the fuel intake . You can also try the MAF sensor. Mass Airflow Sensor located on the big pipe on the air cleaning system.

Jan 06, 2010 | Mercedes-Benz 560-Series Cars & Trucks

1 Answer

Key cylinder wont turn to start car

try spraying some powdered graphite lock lube into the lock cylinder and work the key in and out, do not use any type of oily spray, it may work in the short term but will jam the lock later, the lock lube is avil from any hardware store.

Sep 11, 2009 | 2002 Dodge Stratus

2 Answers

No turn signals, no tail lights and fuses are good

Replace the non-working tail light bulb. Try replacing the bulbs for the turn signals. If that doesn't work, replace the relay.

May 24, 2009 | 1995 Isuzu Rodeo

1 Answer

Windshield wipers wont work when i engage the sprayers

Try blowing the switch out with compressed air moving it from every position. If this fails, replace the switch. Frankster016

Oct 26, 2008 | 1994 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides