Question about Saturn SC1

1 Answer

Changed master and slave on 01 saturn sc1 clutch peddal looses presure how do i solve this

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 202 Answers

Easy way is one person pushes down on pedal and other bleeds out slave. Good luck

Posted on May 20, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 saturn ion hpw do I change the clutch is it a kit or seperatly ? like the slave and master drive or cylinders and how do I kmo w for sure that its that tthat needs to be changed


if you gave some indication of the problem of the clutch maybe we could help
was the clutch master cylinder replaced because that is one of the main reasons clutch will slip

Jul 13, 2017 | Saturn Cars & Trucks

1 Answer

How do I fill the slave unit of a hydraulic clutch 04 saturn


Fill the master, and bleed the slave, just like you bleed a brake system. Takes two people, and three are better.
Pump clutch. Hold down.
Open bleed valve on slave.
Close bleed valve on slave
add fluid to master.
repeat until no air comes out when you open bleed valve on slave.

May 24, 2015 | Saturn Cars & Trucks

2 Answers

Stiffer clutch


Not sure why you replaced master and slave. might be disc or pressure plate problem. If not, then you still have some air in the system. I suggest using a MitiVac which uses vacuum instead of pumping the pedal. It is an easy tool to operate and only requires 1 person, you squeeze it by hand. Sometimes it can be stubborn air bubble, but you must have full pedal travel to clear the gears when you shift. Hope that helps.

Dec 31, 2013 | Cars & Trucks

1 Answer

Clutch bleeding


loosen the line at the master cylinder to allow the master cylinder to prim properly then bleed out the system. There is still air in the system.

Dec 31, 2013 | Saturn Cars & Trucks

1 Answer

Clutch fluid leaking under engine 2002 Saturn Vue


Could be your clutch slave cylinder,here's how to replace.

Mar 01, 2013 | 2002 Saturn VUE

1 Answer

To take off clutch master cylinder man tt zx


just go ahead to replace the cylinder.

Jan 29, 2012 | 1990 Nissan 300ZX

1 Answer

How to bleed the clutch on a 2001 saturn sc1


very hard to get to, shops sell them as pre-bled master and slave unit.

Oct 21, 2010 | 2005 Saturn SC1

1 Answer

How do you change a clutch cable on 97 saturn sc1?


Impossible as it has a hydraulic clutch, and no it cannot be adjusted. It has a small master cylinder and a slave cylinder, just like a brake system. If one of those has failed, you buy a pre-bled replacement for the whole little system and bolt it in.

Aug 30, 2010 | 1997 Saturn SC

1 Answer

How do i get the slave cylinder out of the trans on a 95 saturn sc1


Unbolt the the two nuts that hold it onto the transmission. Then grab the slave cylinder and turn it counter clockwise and it should pop out. That is correct because holding it in the hole and turning it clockwise seats it back into the transmission.

Remember to remove the connection between the clutch pedal and the master cylinder or put a brick or something to hold the clutch pedal up or else removing the slave cylinder without the above note will ruin the hydraulics and allow air to get into this airless system.

Feb 26, 2010 | 1995 Saturn Sc

1 Answer

Bleed the clutch


No way to bleed the clutch system.You need to buy a clutch master/Slave assy from saturn.Comes completely full of fluid & ready to install.It has retainers to hold slave pin in place until fully installed.Once installed you push the pedal & you will hear a faint click which is the slave retainer breakaways relieving.No other way to bleed although aftermarket parts house will sell you individual pieces.hope this helps

May 17, 2009 | 2002 Saturn SC

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...