Question about 2008 Volkswagen Touareg 2

Open Question

How do i remove and refit camshafts on a v/w touareg 2.5 tdi

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: VW Touran 2.o TDI Wiper Problem

hi
its weird ,but you know wipers is not working when computer senses open hood , so you have to look at hood catch. i'm not sure contacts have to be closed or open . anyway it is easy to check
good luck

Posted on Jul 13, 2009

Ad
jimboz4
  • 305 Answers

SOURCE: Wear is the batary on VW touareg 2 5 tdi

are you really ready for this..
if (typeof InitForm != "undefined") InitForm('lookup1','autodiv1','down');
Under the drivers seat. OK, let's add to this...

It's a tad more complicated. There are two plastic covers at the front of the seat on the floor. You need to lift both of them up. That exposes a fastener that will require a 10mm "triple square" male tool. This is similar to the familiar Torx (6 point star) fastener except it has 12 points instead of 6 points. This tool is available at many auto supply places, without it, you will NOT replace the battery. Remove both screws (they're TIGHT!!!), remove the plastic trim pieces from the rear of the seat slide assembly (carefully snap off) Tilt the seat back all the way forward, slide the seat forward almost all the way but leave space to miss the steering wheel. Now push back on the seat back and the entire seat will tilt to the rear exposing the battery box under the drivers seat. There are four clips that hold the cover on, unhook them, remove the torx screw holding the heater deflector to the battery box lid, remove the wire tie holding the wire to the top of the box and remove the box cover. Now you see the battery. Remove the gas vent plastic pipe from the front, remove the metal cover at the front left corner (10mm socket) it will not come out until you remove the (-) cable but don't just yet. remove the side clamp (10mm socket) and the battery is loose and free. It would be smart (but not required) to provide a 12 volt electrical source to the battery terminals as you replace the battery to help keep all of the radio GPS etc, settings. Remove the terminals, lift out the battery.

Posted on Sep 17, 2009

  • 4793 Answers

SOURCE: have a 2.5tdi pd touareg. need timing marks?

the timing marks for all vw/audi/seat and skoda are on the front pulleys(they are small dots)you may need to highlight them with chalk.

Posted on May 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the turbo vw touareg v6 tdi


SAFE MODE CAUSES THE POWER FAILURE!!MAKE SURE THAT U HAVE NO DTCS STORED AND IF NOT SEND ME THE VIN TO HELP U FURTHER!!

Feb 27, 2014 | 2008 Volkswagen Touareg

1 Answer

Where do i find the engine no on my 05 v6 toureg


2005 VW Touareg V6 3,2 petrol engine:
tdisline_813.jpg

2005 VW Touareg V6 2,5 TDI engine:
tdisline_814.jpg

Aug 03, 2011 | 2004 Volkswagen Touareg

1 Answer

Seat inca van 00 sdi 1.9 diesel.. tension polly came loose.. timing belt slipped.. I need to know how to reset it again. Where are the markings on the crank shaft and the cam shaft? Please attach any...


Timing belt set-up for a 2000 Seat Inca 1.9 SDi

1. Align the crankshaft timing marks on the flywheel / gearbox

tdisline_583.jpg
2. Remove the valve cover
3. Lock the camshaft

tdisline_584.jpg
4. Fit the injection pump locking pin

tdisline_585.jpg

5. Loosen the camshaft gearwheel bolt, 180 degrees. Use a wrench to counter-hold
6. Loosen the camshaft gearwheel while holding it in place

tdisline_586.jpg

7. Fit the timing belt in the sequence as shown in the below figure: a - b - c - d - e - f - g

tdisline_587.jpg

8. Fit the timing belt and camshaft gearwheel together
9. Turn the tensioner clockwise to align both marks

tdisline_588.jpg

10. Tighten the large bolt on the tensioner to a torque of 20 Nm
11. Check for correct fit
12. Lock the camshaft. Tighten the camshaft gearwheel bolts: 45 Nm. Use a wrench to counter-hold
13. Remove helping tools
14. Turn the engine two rotations by hand
15. Repeat the procedure if required
16. Fit the vacuum pump
17. Refit the crankshaft pulley. Tighten torque: 20 Nm + 20 degrees
18. Fit the timing belt cover
19. Refit the valve cover
20. Fit the ancillary drive belt
21. Refit the inlet air manifold hoses
22. Check the injection timing

Torque settings:
Camshaft gearwheel: 45 Nm
Tensioner pulley: 20 Nm
Crankshaft pulley: 20 Nm + 20 degrees

May 26, 2011 | Volkswagen Passat Cars & Trucks

2 Answers

2006 jetta tdi oil change


Consult the Owner's Manual, or view the oil specifications on the fill cal or dipstick (usually the fill cap) located under the hood. Depending upon mileage you may not want to vary from manufacture specifications, or risk voiding your vehicle's warranty should any remain. The VW TDI's are typically high maintenance engines. I would strongly recommend staying with the manufacture's oil specifications, and do not overfill the oil in your vehicle.

Jun 02, 2010 | 2001 Volkswagen Jetta TDI

1 Answer

Have a 2.5tdi pd touareg. need timing marks?


the timing marks for all vw/audi/seat and skoda are on the front pulleys(they are small dots)you may need to highlight them with chalk.

May 10, 2010 | 2004 Volkswagen Touareg

1 Answer

Touareg Battery


Hi,

There are three different battery configurations in the Touareg.
1) Touaregs with the V-10 TDI engine come equipped with two batteries, the additional one of which is normally dedicated to the engine start procedure exclusively.
2) Some Touaregs without the V-10 TDI engine come equipped with two batteries. In these vehicles, the extra battery is always dedicated to an additional water heater.
3) Some Touaregs without the V-10 TDI engine come equipped with only one battery.
Currently, all gasoline engine Touaregs sold in the US include only one battery. All diesel engine Touaregs sold in the US have two batteries.

" In all Touaregs, the main battery is located under the driver's seat. In Touaregs with two batteries, the additional battery is located beneath the floor of the rear storage area, occupying the space that the spare tire would normally occupy".

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!


Jul 12, 2009 | 2006 Volkswagen Touareg

1 Answer

TIMING BELT POINTS.


– Mark direction of rotation of toothed belt with coloured felt tip marker pen. – Turn crankshaft to TDC. Mark on toothed belt guard -A- must align with mark on V-belt pulley -B-. – Check position of camshaft pulleys. The larger hole in the locking plates -arrows- must face inwards. hinweis.gif Note If the larger hole in the locking plate is positioned to the outside on the toothed belt pulley, the crankshaft must be turned one revolution in direction of engine rotation. – Remove sealing plug -arrow- from left side of cylinder block. The TDC drilling in the crankshaft must be visible (or able to be felt) in the sealing plug hole. – Screw clamping bolt -3242- carefully into hole onto limit stop so that the crankshaft is secured against turning. – Remove central toothed belt guard. – Unscrew vibration damper. hinweis.gif Note The vibration damper is secured to the crankshaft with 8 bolts. – First remove bolt -1- from oil filter housing, then remove bolts -2- for toothed belt tensioning element cover. – Remove cover. hinweis.gif Note t The toothed belt tensioning element is oil dampened. It can therefore only be pushed back slowly. t Use locking pin -T40011- to lock tensioning element. – If necessary, align holes in housing and on tensioning element piston, before tensioning using long nose pliers or a thin wire. – Turn tensioning lever of toothed belt tensioning roller -1- in -direction of arrow- using hexagon key. – Secure tensioning element with locking pin -T40011- when the tensioning lever of the toothed belt tensioning element -2- has been pushed back so that the holes in the housing and the pistons align. – Seat the camshaft clamp -T40005- into the camshaft locking plates and loosen the securing bolts approx. 5 turns. – Remove camshaft clamp -T40005- again. – Now pull the camshaft pulleys off the tapers using two-arm puller -T40001- and legs -T40001/2-. – Loosen tensioning roller -arrow- and remove toothed belt.

Jan 25, 2009 | 2004 Volkswagen Touareg

2 Answers

VW Touran 2.o TDI Wiper Problem


hi
its weird ,but you know wipers is not working when computer senses open hood , so you have to look at hood catch. i'm not sure contacts have to be closed or open . anyway it is easy to check
good luck

Jul 07, 2008 | 2004 Volkswagen Touareg

Not finding what you are looking for?
2008 Volkswagen Touareg 2 Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...