Question about 1982 Ford F 250

1 Answer

82 Ford F250

I cant get the front brakes off my 82 Ford F250 any suggestions...?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Do you mean the callipers or the disk? the callipers you should find on the rear of the calliper two bolts should be 1/2 in or 13mm,these bolts are in between the slider bolts for calliper. if they won't go willingly try heating them up with a propane torch be careful not burn the pads or the hose or sensor if you have one once warm try agin with a socket or wrench if no lu goto any car parts store and get some liquid wrench wait til they cool and sprayon wait til next day and they should come out alot easier ...if its the disk use a big hammer or a small sledge don't hit it on where the pads go oron the edge a firm hit close to the hub will doit .. be careful once you have the calliper off make sure you tie it up with some rope or a bungie so you damge the hose godd luck

Posted on Aug 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque specs for brake calipers on a ford explorer sport front calipers


  1. Torque Specs For F250 Caliper Bolts - Diesel Forum - TheDieselStop.com

    www.thedieselstop.com > ... > 1999-2007 General Questions Jan 13, 2009 - 3 posts - ‎1 author
    Does any one know what the caliper bolts torque specs are? ... Disc brake caliper pin bolts - Excursion, F-250/F-350 with Ford and Dana axle ... Torque specs for front brakes
    5 posts
    Mar 12, 2009
    05 F250 brake torque specs please
    6 posts
    Aug 22, 2007
    Brake caliper torque specs
    5 posts
    Jul 14, 2007
    Front brake Caliper Bolt Torque
    6 posts
    Apr 25, 2005
    More results from www.thedieselstop.com

Jul 11, 2015 | 1998 Ford Explorer

2 Answers

I OWN A 2004 FORD F250 4-2.WHEN I BRAKE AT ANY SPEED THE FRONT END SHAKE VERY BAD . YOU DONT FEEL ANY THING IN THE BRAKE PEDDLE.THE STEERING IS FINE .REPLACED ROTORS ,INTER AND OUTER BEARING,NEW BRAKE...


the struts in the front are broke this is what keeps your truck off the tire its sits inside the spring and if they break this will mess with the way it brakes and turns :) hope this helps

Mar 24, 2010 | 2004 Ford F250

2 Answers

Ford F250 SD, 2wd. Replacing front bearing


If you have front disk brakes you have to remove the brake caliper to get the rotor off.

Oct 03, 2009 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

82 F250 Tail lights out


check for a blown 15 amp fuse,probably shorted out and blew.if its good then replace the headlight switch

Sep 07, 2009 | 1982 Ford F 250

2 Answers

1982 Ford F250 5.8L starting problems


82 should be mechanical pump,drivers side in front of engine by oil filter,filter is inside fuel line at the carb

Aug 10, 2009 | 1982 Ford F 250

1 Answer

82 f250 motormounts


You can try to soak them with wd-40 and let them sit overnight; it may penetrate enough to allow them to break with a cheater bar attached to your ratchet. Next I would try to use air impact on them. it may be difficult to access them, but you can use swivels and extentions. Last, cut them; either with a torch, or grinder. You can purchase new motor mounts from NAPA, and they're usually in stock.

I hope this helps you, and I wish you luck with your repair.

May 07, 2009 | 1984 Ford F 250

1 Answer

F250 SD anti lock brakes


try taking wheels off and power washing the whole brake area. i had a similiar problem and doing solved the problem.make sure you do all 4 of them because scanning is not great. if this helps please rate. joe

Nov 23, 2008 | 2003 Ford F250 Super Duty Crew Cab

2 Answers

Front hubs sticking in locked position need to rebuild, How to and any suggested parts for replacement


replace your auto/lock hubs with WARN manual lock hubs,this will save you hunderds.as long as you dont mind having to get out to lock in. NAPA.

Oct 18, 2008 | 2000 Ford F250 Super Duty Crew Cabs

2 Answers

Ford f250 diesel 2002


Its has to come of from the back. Is a 45 min job in at the dealer, so it is a big job. All the bolts for taking it off are in the back,plus you have to take every thing of thats in the way, tire rod end, etc.

Jun 23, 2008 | 2000 Ford F250 Super Duty Crew Cabs

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...