Question about 2003 Mazda MPV

Open Question

I have a 2003 mazda mpv that is ging a P0431 code. What would cause this?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
StormStrikes
  • 104 Answers

SOURCE: how do i get the trouble codes off a 1989 mazda mpv?

http://img178.imageshack.us/img178/3331/obdikx3.jpg

The above link is to a diagram of your ALDL connector, all you need is a paper clip, straighten out the paper clip and insert one end into the diagnostic test pin and one in the system ground pin (terminals A & B).

Then put the key in the ignition and turn it to the on position but DO NOT start the engine. You will then see the check engine light flash. It will initially start by flashing once, then a pause and then flash twice and it will repeat this three times. That flash sequence indicates 12, which just means the system is operating. Its the flash sequences after that that will give you the code if any are stored.

For instance if it flashes twice, then pauses, then flashes four times, thats code 24. So any flash sequence you get after the initial 12 (flash once, pause, flash twice) you need write those down. Below is a list of diagnostic codes to tell you what the codes mean.

Code 12
1 flash, pause, 2 flashes
Diagnostic: This Code will flash whenever the diagnostic terminal is grounded with the ignition switch turned on and the engine is not running.

Code 13
1 flash, pause 3 flashes
Oxygen sensor voltage stays between 0.35 and 0.55 volts for 30 seconds when the TPS signal was above 0.55 volts. The engine had been running for at least 40 seconds with an engine temperature above 110° F.

Code 14
1 flash, pause, 4 flashes
Coolant temperature sensor signal indicates a temperature of over 284° F for 4 seconds after the engine had been running for at least 10 secondsCoolant Sensor Circuit (high temperature) If the engine is experiencing overheating problems, have those fixed before continuing. Check all wiring and connectors associated with the coolant temperature sensor. Replace the Coolant temperature sensor.

Code 15
1 flash, pause, 5 flashes
Coolant Sensor Circuit (low temperature) Coolant temperature sensor signal indicates a temperature colder than -36° F for at least 4 seconds after the engine had been running for 2 seconds. See above, then check wiring connections at the ECM

Code 16
1 flash, pause, 6 flashes
Charging system voltage was either below 9 volts or above 17 volts for 10 seconds. System High Voltage If the voltage is above 17.1 volts for more than 2 seconds, the Service Engine Soon light will illuminate. Have the charging system checked.

Code 17
1 flash, pause, 7 flashes
PCM did not detect any spark reference pulses within 240 fuel control reference pulses (80 crank revolutions) while engine was running below 1200 RPM. Spark Reference Circuit.

Code 21
2 flashes, pause, 1 flash
Throttle Position Sensor, TPS voltage was above 0.8 volts for 5 seconds when engine was running and air flow was less than 15 gm/sec, or the TPS voltage was over 4.8 volts at any time.

Code 22
2 flashes, pause, 2 flashes
Throttle Position Sensor check TPS adjustment. Replace the TPS sensor. TPS voltage was under 0.2 volts for 4 seconds when the ignition was on. Check for a sticking, or mis-adjusted throttle position sensor.

Code 23
2 flashes, pause, 3 flashes
Inlet air temperature sensor signal showed an air temperature of -29° F for 4 seconds. Manifold Air Temperature. Check the MAT sensor, wiring, and connectors for a possible open circuit. replace the MAT sensor.

Code 24
2 flashes, pause, 4 flashes
Vehicle speed sensor signal showed less than 3 MPH for 2 seconds when engine speed was greater than 3000 RPM and transmission has not been in park or neutral for more than 4 seconds. Or vehicle speed goes from above 18 MPH to 0 in less than 2 seconds without applying brake. This code can only appear when the vehicle is in motion, if it appears when the car is not in motion, ignore it. Check ECM connections, any other problems should be diagnosed by a qualified mechanic.

Code 25
2 flashes, pause, 5 flashes
Inlet air temperature sensor signal showed an air temperature of over 218° F for 5 seconds when vehicle speed was greater than 35 MPH. Check the voltage between the MAT sensor and the ECM. voltage should be above 4 volts.

Code 26
2 flashes, pause, 6 flashes
Quad-Driver sense voltage shows a low voltage when battery voltage should be present, or if the sense voltage shows battery voltage when a low voltage should be present for at least 5 seconds when the engine was running. Have the car checked by a dealer.

Code 27
2 flashes, pause, 7 flashes
2nd gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 2nd or 4th gear switch was open when engine was first started. Gear switch Diagnosis Have the car checked by a dealer.

Code 28
2 flashes, pause, 8 flashes
3rd gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 3rd or 4th gear switch was open when engine was first started.

Code 29
2 flashes, pause, 9 flashes
4th gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 4th gear switch was open when engine was first started.

Code 31
3 flashes, pause, 1 flash
PRNDL indicates a gear other than park or neutral for 13 seconds for 3 consecutive startups when ignition was on, engine was off and vehicle speed was 0. Or the PRNDL status indicators (A, B, C, P) showed an incorrect combination of Lo and Hi for more than 10 seconds.
Check all connectors, and for a faulty switch.

Code 32
3 flashes, pause 2 flashes
EGR System Check vacuum hoses and connections for leaks and restrictions. Replace the EGR solenoid or valve.

Code 33
3 flashes, pause, 3 flashes
MAF Sensor Have the mass air flow sensor replaced.

Code 34
3 flashes, pause, 4 flashes
There was no MAF signal for over 4 seconds while engine was running. Check for loose or damaged air duct, misadjusted minimum idle speed and cacuum leaks. Inspect the MAF sensor and the electrical connections.

Code 38
3 flashes, pause, 8 flashes
The Torque Converter Clutch portion of the brake switch was open and caused the TCC to be inoperative, adjust OR replace switch.

Code 39
3 flashes, pause, 9 flashes
Torque Converter Clutch Check ECM connections, check for faulty Torque Conver Clutch solenoid.

Code 41
3 flashes, pause, 1 flash
Cam sensor signal was not received by PCM for the last 5 seconds while engine was running. Check for faulty connections, or a faulty cam sensor. Maybe also indicate a problem with the vehicle's timing chain.

Code 42
4 flashes, pause, 2 flashes
The Electronic Spark Timing (EST) signal did not change when the ECM applied bypass voltage to the ignition module. Check for faulty connections, or a faulty ignition module.

Code 43
4 flashes, pause, 3 flashes
Knock sensor signal was either above 3.5 volts or below 1.5 volts for at least 20 seconds. Check for a faulty knock sensor, or Mem-Cal.

Code 44
4 flashes, pause, 4 flashes
Oxygen sensor voltage was under 0.25 volts for up to 4 1/2 minutes of closed loop operation, lean exhaust. Check the ECM wiring connections. Check for vacuum leaks at the hoses and intake manifold gasket.

Code 45
4 flashes, pause, 5 flashes
Oxygen sensor voltage was over 0.75 volts for 2 minutes in closed loop operation with a throttle angle between 0.6 and 1.9 volts. Rich exhaust. Check the evaporative charcoal canister and its components for the presence of fuel.

Code 46
4 flashes, pause, 6 flashes
Power Steering pressure switch Check for faulty connections, or a faulty switch.

Code 48
4 flashes, pause 8 flashes
Misfire Diagnosis. Check the ignition and fuel systems.

Code 51
5 flashes, pause, 1 flash
Prom or Mem-Cal Make sure the MEM-Cal or prom is properly installed in the ECM. Replace Mem-Cal or prom.

Code 52
5 flashes, pause, 2 flashes
Cal-Pak Check the Cal-Pak to insure properation. replace the Cal-Pak.


Code 54
5 flashes, pause, 4 flashes
EGR #2 solenoid was out of range for 6 of 8 tests. 55 EGR #3 solenoid was out of range for 3 of 5 tests.

Code 55
5 flashes, pause, 5 flashes
ECM Check for faulty connections. Replace the ECM.

Code 56
5 flashes, pause, 6 flashes
Quad-driver voltage was incorrect for 5 seconds on the circuit connected to QDM "B".

Code 57
5 flashes, pause, 7 flashes
Boost control solenoid did not open bypass valve causing engine torque to be too high.

Code 63
6 flashes, pause, 3 flashes
EGR flow was incorrect. EGR solenoid did not work properly. Have vehicle serviced by a dealer.

Code 64
6 flashes, pause, 4 flashes
Same as Code 63 EGR flow was incorrect. EGR solenoid did not work properly.

Code 65
6 flashes, pause, 5 flashes
Same as Code 63.

Posted on Dec 31, 2008

Ad
lsteward68
  • 331 Answers

SOURCE: i have a fault code of p0108 what has caused this

Your map sensor, otherwise known as mass air flow sensor is probably bad. You should replace it. it is normally located between the air filter and the throttle body. It senses how much air is going into the throttle body so the car knows how much fuel to inject.

Posted on Jul 07, 2009

pippall
  • 1486 Answers

SOURCE: Mazda mpv 2003 check engene light code p0421 warm up catalist ...

replace the air flow meter has this sounds like your problem.Good luck.

Posted on Jul 27, 2009

Hrnsly
  • 154 Answers

SOURCE: 2001 Mazda MPV Error code

THAT CODE IS FOR THE BANK 2 OR FRONT CATALITIC CONVERTER ON THE VAN. YOU CAN HAVE THE DEALER REPLACE IT OR A MUFFLER SHOP CAN DO IT. THE CAT IS A PART OF THE FRONT EXHAUST MANIFOLD AND WILL NOT BE CHEEP TO REPLACE.

Posted on Aug 18, 2009

  • 645 Answers

SOURCE: What are codes P1492, P0421 & P0431 on the

po421 warm up catalyst efficiency below threshhold bank 1, 431 same on bank 2..

Posted on Feb 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 ES. What are the probable causes of DTCs P0421 and P0431?


code p 0421 refers to warm up cat converter bank 1--efficiency below threshold ===causes ---cat converter---wiring---HO2S 2
( heated oxygen sensor)
code p 0431 refers to warm up cat conveter bank 2--efficiency below threshold === causes cat converter --- wiring---HO2S 2
as the same HO2S appears in the cause of the fault I would be inclined to change it first
the HO2sS sensor is the one in the exhaust manifold or before the cat converter
and 2 is in the front bank of a V engine
use the special socket when removing/ replacing these sensors as an incorrect tool is the main reason for wire failures on the sensors

Dec 17, 2015 | 2003 Mazda MPV

1 Answer

My fan on my 2003 mazda mpv starts running as soon as i turn on the ignition. could this cause erractic codes


the temperature cooling sensor, The sensor's output is monitored by the engine computer to regulate various ignition, fuel and emission control functions, and to turn the radiator-cooling fan on and off as needed. check this first ! also check the fan relay in relay box. it may be sticking in the on position. hard to say without being there. but try the above things. good-day ! the fans come on if a/c is on.

Mar 17, 2012 | 2003 Mazda MPV

1 Answer

2003 mazda mpv. I REPLACED THE UPPER PVC HOSE.


Tcs is not related to the engine. Please get a scan and post the trouble codes here.

Jul 19, 2017 | 2003 Mazda MPV

3 Answers

I have a 2003 MPV with trouble code PO327 and PO431. What do these mean? Thank you.


P0327 Knock Sensor 1 Circuit Low Bank 1 or Single Sensor
P0431 Warm Up Catalyst Efficiency Below Threshold Bank 2


Sep 28, 2009 | 2003 Mazda MPV

1 Answer

I have a 2003 MPV and getting a troble code PO111. Just wondering what it is? Thank you.


Intake Air Temperature Sensor Circuit Range/Performance
Possible Causes:


IAT sensor signal circuit has high resistance IAT sensor has drifted out of calibration IAT sensor is damaged or has failed PCM has failed

Sep 28, 2009 | 2003 Mazda MPV

1 Answer

2001 Mazda MPV Error code p0431 makes engine light come on


THAT CODE IS FOR THE BANK 2 OR FRONT CATALITIC CONVERTER ON THE VAN. YOU CAN HAVE THE DEALER REPLACE IT OR A MUFFLER SHOP CAN DO IT. THE CAT IS A PART OF THE FRONT EXHAUST MANIFOLD AND WILL NOT BE CHEEP TO REPLACE.

Jun 27, 2009 | 2001 Mazda MPV

1 Answer

Error code P0431


P0431 Left Hand Warm-up Catalyst System Efficiency Below Threshold.

Jun 27, 2009 | 2001 Mazda MPV

1 Answer

2003 Mazda MPV codes P0102, 0108, 0113, 0421, 0431, 0505, 0507


The codes are mass air flow sensor,manifold pressure, intake air temp, catalytic converter.

The only thing I cant think of is that the manifold seals are defective and theres no back pressure which would explain the erradic idleing.

Apr 25, 2009 | 2003 Mazda MPV

1 Answer

2003 Mazda MPV trouble codes


check the pcv hose at the back of the intake manifold it often leaks and will cause several idle problems

Sep 29, 2008 | 2003 Mazda MPV

Not finding what you are looking for?
2003 Mazda MPV Logo

Related Topics:

1,031 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...