Question about 2006 Nissan Altima

1 Answer

Sometimes it will start right up. often it will crank but not start until 6 or 8 tries. Already replaced spark plugs and crankshaft sensor

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 3,530 Answers

Welcome to Fixya

Sounds like that there is no fuel getting to the cylinders. Check/inspect the fuel injector relay. Replace it if possible.

Thank you for using Fixya!

Posted on May 20, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

The car wont start when its cold outside I have already replaced crankshaft posistion sensor and had tge fuel pump checked

Year/make/model???? Possible coolant sensor out of range. Does it try to start or just crank over and not start?

Nov 08, 2015 | Cars & Trucks

1 Answer

My 2000 cadillac deville just shuts off periodically an fires right bk up sometimes then sometimes it wont can anyone tell me wat this could be

When it won't start right back up , check an see what's missing ! Spark - pull a plug wire an hold it close to something metal better yet put a screw driver in the plug wire end an hold close to a metal part of the engine an have someone crank over the engine ! Then if there is spark ,spray some stating fluid into the throttle plate . if it tries to start you have a fuel problem . If there is no spark could have a bad ignition control module , or coil or the crankshaft position sensor may be going bad ! Does your caddy have a tachometer ? See if it moves while cranking , if not bad crank sensor !

Feb 16, 2015 | Cadillac Cars & Trucks

1 Answer

Crankshaft Position Sensor

As the main sensor the computer uses to calculate the timing of the spark, it can cause a no spark condition. Or sometimes if not working right, the engine won't stay running-it will start and quickly shut off. You cannot really tell if it is working or not, without testing the circuit (3 wires usually-a ground wire, a signal wire to computer, and a 5 volt reference signal from the computer).
If you have no spark on a spark plug wire, it could be the crank sensor or circuit, but without testing it is just a guess.

Jan 03, 2014 | 1996 Dodge Caravan

2 Answers

99 stratus 2.5 v-6/no spark.will crank over.


  1. Remove speed control servo from driver's side strut tower.
  2. Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor
  3. Pull crankshaft position sensor straight up out of the transaxle housing.
  4. (Disconnect crankshaft position sensor electrical connector from the wiring harness connector.
INSTALLATION - ADJUSTABLE All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor.
NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer
  1. Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque.
  2. Connect crankshaft position sensor electrical connector to the wiring harness connector.
  3. Attach connector to heater tube bracket.
  4. Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque.

May 19, 2012 | 1999 Dodge Stratus

1 Answer

I have replace the spark plugs, wires, coil, crank...

You replaced all kinds of parts for no reason. Do you really think, at this time,that even one item was your problem.
I would suggest going to a repair shop,as you already spent more than, that would have cost,in the first place.

May 09, 2010 | Cars & Trucks

2 Answers

1996 Jeep Grand Cherokee No Start

I would be thinking that there is a good chance that you need to be checking out replacing the computer, if you aren't getting any communication with the proper scan tool then the computer isn't communicating with anything in the vehicle...... I would have guessed first off that the ignition control module might be bad but that is obviously part of the computer also, I would be looking in that direction.

Sep 19, 2009 | 1996 Jeep Grand Cherokee

2 Answers

Car stalls while driving

you have a bad crankshaft sensor. replace the crank sensor.

dodges and gm's are known for this problem.

Apr 10, 2009 | 1998 Plymouth Neon

2 Answers

No spark

before you replace the computer have the crank sensor replace it is located between transmission and engine by the driver's side on top of transmission
most likelly your computer is ok
the distribuitor has nothign to do with spark on this cars

Jun 02, 2008 | 1999 Jeep Cherokee

Not finding what you are looking for?
2006 Nissan Altima Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

79865 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides