Question about Daewoo Nubira

1 Answer

I have a 2001 nubira it does not shift out of low gear and it has reverse. what could be causing this to happen.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 226 Answers

Did you check the trans fluid? Do you know how to check the fluid? If so,check it and add if needed. If fluid is ok it could be a couple of things, worst being trans is bad.

Posted on May 20, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I have a 2001 elantra. What would make it stay in reverse and 1st gear.it is a manual transmission


when you put it in reverse,first thing you feel a spring.after tthat you lift,
a security plate,this plate prevent you from going reverse into 1 gear.
cause the axel turn a little further when you allreddy has stop the car.
this takes two sec.thats why when putting it in reverse after you feel the spring you wait two seconds,then puch al the way in reverse.

Jul 26, 2014 | 2001 Hyundai Elantra

1 Answer

The gear shift in my 2001 Daewoo Nubira is sticks in the Park Position. I can insert my car key into a slot next to it to release it, but this is not a normal procedure. How can I correct this problem?


I had the same problem....try replacing the Clock/Radio fuse located behind a panel inside the car on the driver side. Tell me if it works, it worked for me

Dec 05, 2010 | 2001 Daewoo Nubira

1 Answer

Transmission has reverse and low. Will not shift into any other gear.Was working fine but then would not shift from Low into any other gear. It still has reverse.


most likely it is in fail safe mode witch is 2nd gear. This happens when the computer sees something something wrong. If the speedo is still working it's not the output sensor and could be the solenoid pac.

Oct 31, 2010 | 2007 Chrysler Town & Country LX New Cars

1 Answer

Reverse Gear shifting vibration and bell like sound


Check the "u" joints on the driveshaft ends. at least one end has failed.

Sep 23, 2009 | 2001 Jeep Grand Cherokee

1 Answer

Vibration when using reverse gear .when shifting to reverse gear i feel vibration like oil pump vibration


Have your motor mounts checked very soon. This only shows in reverse because reverse causes a backward torque than the engine does in forward gear.

Sep 13, 2009 | 2001 Jeep Grand Cherokee

1 Answer

My 2001 lincoln ls wont go into 4th or 5th gears. Took it to a trans shop and they recommended a rebuild for 3000+ dollars. But Ive been reading that alot of lincolns with the same problem getting err


call your dealer to get an estimate too.

Shift Patterns Upshifts
Transmission upshifting is controlled by the powertrain control module. The PCM receives inputs from various engine or vehicle sensors and driver demands to control shift scheduling, shift feel and torque converter clutch (TCC) operation.
The PCM has an adaptive learn strategy to electronically control the transmission which will automatically adjust the shift feel. When the battery has been disconnected, or a new battery installed certain transmission operating parameters may be lost. The Powertrain Control Module (PCM) must re-learn these parameters. During this learning process you may experience slightly firm shifts, delayed, or early shifts. This operation is considered normal and will not affect the function of the transmission. Normal operation will return once these parameters are stored by the PCM.
---------------------------------------------------------------------
Apply Components Band — Overdrive
For component location, refer to Disassembled Views in this section.
During 2nd and 5th gear operation, hydraulic pressure is applied to the overdrive servo.
  • This pressure causes the piston to move and apply force to the band.
  • This action causes the overdrive band to hold the overdrive drum.
  • This causes the overdrive sun gear to be held stationary through the adapter plate and the overdrive drum.
Band — Low/Reverse
For component location, refer to Disassembled Views in this section.
During 2nd gear operation, 1st gear operation and reverse, hydraulic pressure is applied to the low/reverse servo.
  • This pressure causes the servo to move and apply force to the low/reverse band.
  • This action causes the low/reverse brake drum to be held.
  • This action causes the low/reverse planetary assembly to be held stationary.
Band — Intermediate
For component location, refer to Disassembled Views in this section.
During 3rd gear operation, hydraulic pressure is applied to the intermediate servo.
  • This pressure causes the servo to move and apply force to the intermediate band.
  • This action causes the direct clutch drum to be held.
  • The intermediate band holds the intermediate brake and direct clutch drum to the case in 3rd gear.
  • This causes the input shell and forward sun gear to be held stationary.
Clutches — Direct
For component location, refer to Disassembled Views in this section.
The direct clutch is a multi-disc clutch made up of steel and friction plates.
  • The direct clutch is applied with hydraulic pressure and disengaged by return springs and the exhaust of the hydraulic pressure.
  • It is housed in the direct clutch drum.
  • During 4th, 5th, and reverse gear application, the direct clutch is applied transferring torque from the forward clutch cylinder to the direct clutch drum.
  • This action causes the forward sun gear to drive the pinions of the low/reverse planetary carrier.
Clutches — Forward
For component location, refer to Disassembled Views in this section.
The forward clutch is a multi-disc clutch made up of steel and friction plates.
  • The forward clutch is applied with hydraulic pressure and disengaged by return springs and the exhaust of the hydraulic pressure.
  • The forward clutch is applied in all forward gears.
  • When applied, the forward clutch provides a direct mechanical coupling between the center shaft and the forward ring gear and hub.
Clutches — Coast
For component location, refer to Disassembled Views in this section.
The coast clutch is a multi-disc clutch made up of steel and friction plates.
  • The coast clutch is applied with hydraulic pressure and disengaged by return springs and the exhaust of the hydraulic pressure.
  • The coast clutch is housed in the overdrive drum.
  • The coast clutch is applied when in 1st, 3rd, D4, and reverse positions.
  • When applied, the coast clutch locks the overdrive sun gear to the overdrive planetary carrier, thus preventing the one-way clutch from overrunning when the vehicle is coasting.
    • This allows the use of engine compression to help slow the vehicle and provide engine braking.
Clutches — Intermediate
For component location, refer to Disassembled Views in this section.
The intermediate clutch is a multi-disc stationary clutch made up of steel and friction plates which are in a module assembly that includes the cylinder and frictions.
  • Applied with hydraulic pressure.
  • Disengaged by a return spring and releasing of hydraulic pressure.
  • Hydraulic pressure is feed through a feed tube in the case worm trail.
  • Uses a bonded piston in an aluminum housing.
  • Applied in during a 2-3 shift event.
  • Transfers torque from the sun gear to the planetary carrier.
  • Torque transfer causes the one way clutch to engage and holds the sun gear from turning, delivering 3rd gear.
One-Way Clutch — Direct
For component location, refer to Disassembled Views in this section.
The direct one-way clutch is a sprag-type one-way clutch that is pressed into the center shaft.
  • The direct one-way clutch is driven by the ring gear of the overdrive planetary carrier.
  • The direct one-way clutch holds and drives the outer splines of the center shaft in 1st, 3rd, 4th and reverse gears.
  • The direct one-way clutch overruns during all coast operations and at all times in 2nd and 5th gear.
One-Way Clutch — Intermediate
For component location, refer to Disassembled Views in this section.
The Intermediate One-Way Clutch is a sprag type one-way clutch.
  • The Intermediate One-Way Clutch connects the intermediate assembly to the input shell and sun gear assembly in third gear.
One-Way Clutch — Low/Reverse
For component location, refer to Disassembled Views in this section.
The low/reverse one-way clutch is a sprag type one-way clutch.
  • The low/reverse one-way clutch holds the low/reverse drum and low/reverse planetary assembly to the case in 1st and 2nd gear.
  • In all other gears the low/reverse one-way clutch overruns.
------------------------------------------------------------------------------

May 01, 2009 | 2002 Lincoln LS

1 Answer

Transmission will not shift from low gear.


ok, its the shift solenoid that is malfunctioning here. replacing it will fix this issue.also, check the transmission fluid to see if its low.

Mar 16, 2009 | 1992 Cadillac DeVille

1 Answer

Engine Died on Reverse Gear


try adding some transmition fluid to the transmition . or have it towed to a repair shop

Nov 12, 2008 | 2001 Mazda Tribute

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76051 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...