Question about 1998 Chrysler Sebring

1 Answer

It will be very much appreciated if you could send me the information about how to replace the O2 sensors on a 1998 chrysler sebring convertible.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,170 Answers

Hello, Eventually your Chrysler Sebring's oxygen sensor will go bad and need to be replaced. The oxygen sensor regulates the oxygen-to-fuel ratio in your vehicle. It also controls your gas mileage. It senses when more or less oxygen needs to be pumped into the fuel lines. If it fails, your Sebring will run poorly and won't get very good gas mileage. Knowing how to change it yourself can save your money. Here are the instruction to change o2 sensors.
Locate your Sebring's oxygen sensor on the pre-catalytic converter. This is located near the front right wheel well of your vehicle. Apply some anti-seize paste to the threads of the new oxygen sensor. Be careful not to get any of the paste on the sensor itself, or it will be ruined. This makes for easy removal of the sensor next time.Remove the old oxygen sensor, using the 7/8-inch wrench. Find the stock sensor wire near the engine-loop lift. This will be by the firewall of your Chrysler Sebring. Splice the stock sensor wire and connect it to the new oxygen sensor's wire, using crimp connectors.Remove the large air-intake pipe that runs from the air box to the rear turbo. Then remove the two smaller air pipes that run from the air box to the blowoff valves. This will give you access to the oxygen sensor. Soak the old oxygen sensor in WD-40 to loosen it. Screw in the sensor by hand. Use the wrench to fully tighten the oxygen sensor so it cannot be removed by hand. Replace the air pipes to the correct valves again.


  • Rate me if you like my answer..


    Thanks

  • Posted on May 20, 2011

    1 Suggested Answer

    6ya6ya
    • 2 Answers

    SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

    Hi,
    a 6ya expert can help you resolve that issue over the phone in a minute or two.
    best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
    the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
    click here to download the app (for users in the US for now) and get all the help you need.
    goodluck!

    Posted on Jan 02, 2017

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    2 Answers

    My 1998 chrysler sebring convertable wont start I replaced the fuel filter and fuel pump new battery the car will turn over just wont start


    Verify you have spark, those are known to have issues with the camshaft sensor in the distributor. I have put 2 distributors in my daughter's 97 sebring jxi, did the same thing.

    Jul 22, 2014 | 1998 Chrysler Sebring

    2 Answers

    Chrysler sebring engine codes


    H02S heater control circuit high Bank 2 sensor 2.

    May 19, 2014 | 2004 Chrysler Sebring

    1 Answer

    Where is the 02 sensor located on 06 Chrysler sebring?


    The O2 sensors are in the exhaust pipes before and after the catalytic converter.

    Sep 02, 2013 | 2006 Chrysler Sebring

    1 Answer

    Location & aprox. price for oxygen sensor bank 1, on a chrysler sebring 2004, 2.4liter, dohc, non-convertible?


    A four cyl engine only has one bank. So in your case bank one sensor one is in front of the catalytic converter, and sensor two is after the cat.
    The sensor can cost from $25 to $85 dollars depending on which one and your location.
    Keep in mind the code 420 can be caused by other factors than the O2 sensors.

    Feb 21, 2013 | 2004 Chrysler Sebring

    1 Answer

    1998 Chrysler Sebring convertible Not shifting into drive check engine light came on, error code PO715


    DTC P0715 CHRYSLER - Input Speed Sensor 1 Circuit
    P0715 is detected when TCM or ECM does not receive the proper signal from the sensor.

    The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM).

    Symptoms
    - Engine Light ON (or Service Engine Soon Warning Light)
    - Possible shifting problems

    Possible causes
    - Transmission speed sensor circuit is open or shorted.
    - Poor transmission speed sensor circuit connection
    - Faulty transmission speed sensor

    Hope this clues helps to solve it.

    Jun 02, 2011 | 2003 Chrysler Sebring

    1 Answer

    On my 1998 crysler sebring I am getting OBD II codes of 40 and 41,Transmission & engine module,any suggestions where to start? Thanks.


    code 40-
    Possible causes - 1/1 And 2/1 O2 sensors harness circuit shorted
    - 1/1 And 2/1 O2 sensors harness circuit connectors (wrong connection)
    - Faulty Powertrain Control Module (PCM) P0040 CHRYSLER Description At ignition on the Powertrain Control Module (PCM) checks the voltage on the ground side of the O2 sensor harness connector. If voltage is higher than two volts the P0040 code will set. code 41- Possible causes - 1/2 And 2/2 O2 sensors harness circuit shorted
    - 1/2 And 2/2 O2 sensors harness circuit connectors (wrong connection)
    - Faulty Powertrain Control Module (PCM) P0041 CHRYSLER Description At ignition on the Powertrain Control Module (PCM) checks the voltage on the ground side of the O2 sensor harness connector. If voltage is higher than two volts the P0041 code will set.

    Dec 01, 2010 | 1998 Chrysler Sebring

    1 Answer

    I have a 1996 Chrysler Sebring LX Convertible. Will the O2 sensor stop the car from starting?


    No. I would say replace the coil packs as they have probably gone bad. Fuel pump not coming on might be an issue but you can check power to both to make sure.

    May 18, 2010 | 1996 Chrysler Sebring

    3 Answers

    Code po430 not sure what maybe converter


    One of three (3) possibitlies:
    1. Catalytic Converter is malfunctioning.
    2. O2 Sensor is malfunctioning. This will be the O2 Sensor located on the Catalytic Converter. However you should check and/or replace both sensors if needed.
    3. You have an Exhaust Leak.
    In Order of checking:
    A. Check and Repair any Exhaust Leak.
    B. Replace the O2 Sensor on the Catalytic Converter 1st. Also Known as the Downstream O2 Sensor or HO2 Sensor.
    C. Replace the O2 on the Exhaust Manifold prior to the Catalytic Converter. Also Known as the Upstream O2 Sensor.
    D. Replace the Catalytic Converter.
    Let me know if this helped, or if you have any additional information, problems or questions. Feel free to contact me at FixYa.com!

    Feb 01, 2010 | 1998 Ford Explorer

    2 Answers

    On a 2001 chrysler sebring coupe lxi 3.0 where is the O2 "oxygen sensor" physically located, computer says bank1 sensor2. I know Bank 1 is the side where the #1 cylinder is which I "think" is on the...


    the only sensor that would be on your manifold would be the o2 sensor ihave an intrepid i have four, two converters. 1 before each converter and 1 after each converter. fronts are 1s and backs are 2s all are 4 prong maybe your backs are threes you will need to investigate a little more after all we are dealing with pretty much the same car same year

    Jan 11, 2010 | 2001 Chrysler Sebring

    3 Answers

    98 sebring O2 sensor location


    what engine, is it the O2 sensor or the cat sensor, do u have the trouble code.

    Sep 17, 2009 | 1998 Chrysler Sebring

    Not finding what you are looking for?
    1998 Chrysler Sebring Logo

    778 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8210 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...