Question about 2006 Renault R18

Open Question

Replaced camshaft actuator and cleared engine codes and the light came back on

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Trailblazer, 4.2 I6, code P1345, voltage does not change to cam position actuator 12+ volts all the time?


If this DTC sets, there is a problem with the camshaft position actuator solenoid high control circuit shorted to voltage or the solenoid stuck open.
The PCM sends a pulse width modulated 12 volt signal to a (CMP) actuator solenoid in order to control the amount of engine oil flow to a cam phaser passage.
Do you know what a pulse width modulated signal is ?
Diagnostic Aids
Important: Scan tool control of the CMP actuator solenoid is inhibited when DTC P1345 sets.
The following conditions may cause this DTC to set:
• An improperly torqued harmonic balancer
• A mis-built or mis-timed engine
• A loose or missing crank damper bolt
• The camphaser solenoid stuck open
• The camphaser stuck in a position other than 0 degrees
• The camphaser does not return to 0 degrees within 16 seconds

Do you know what a diagnostic flow chart is ?

If this DTC sets, there is a problem with the camshaft position actuator solenoid high control circuit shorted to voltage or the solenoid stuck open.
Step
Action
Values
Yes
No
1
Did you perform the Diagnostic System Check-Engine Controls?
--
YES - Go to Step 2
NO - Go to Diagnostic System Check - Engine Controls
2
Start the engine.
Clear the DTCs with a scan tool.
Does the scan tool indicate that DTC P0014 failed this ignition?
--
YES - Go to DTC P0014
NO - Go to Step 3
3
Observe the Freeze Frame/Failure Records for this DTC.
Turn OFF the ignition for 30 seconds.
Start the engine.
Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?
--
YES - Go to Step 4
NO - Go to Diagnostic Aids
4
Turn OFF the ignition.
Inspect the crank damper bolt for the proper torque. Refer to Crankshaft Balancer Replacement in Engine Mechanical.
Did you find and correct the condition?
YES - Go to Step 9
NO - Go to Step 5
5
Disconnect the camshaft position actuator.
Remove the camshaft position (CMP) actuator solenoid. Refer to Camshaft Position Actuator Solenoid Valve Replacement .
Jumper the camshaft position solenoid actuator high control circuit of the actuator solenoid assembly to 12 volts. Refer to Using Connector Test Adapters Wiring Systems.
Jumper the low reference circuit of the camshaft position actuator solenoid to a good ground. Refer to Using Connector Test Adapters in Wiring Systems.
Does the pintle inside the CMP actuator solenoid move?
YES - Go to Step 6
NO - Go to Step 8
6
Inspect the CMP actuator for binding or being stuck. Refer to Camshaft Position Actuator Diagnosis in Engine Mechanical.
Did you find and correct the condition?
--
YES - Go to Step 9
NO - Go to Step 7
7
Inspect the engine for correct valve timing. Refer to Camshaft Timing Chain, Sprocket, and Tensioner Replacement in Engine Mechanical.
Did you find and correct the condition?
--
YES - Go to Step 9
NO - Go to Diagnostic Aids
8
Replace the camshaft position actuator solenoid. Refer to Camshaft Position Actuator Solenoid Valve Replacement .
Did you complete the replacement?
--
Go to Step 9
--
9
Clear the DTCs with a scan tool.
Turn OFF the ignition for 30 seconds.
Start the engine.
Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?
--
Go to Step 2
Go to Step 10
10
Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?
--
Go to Diagnostic Trouble Code (DTC) List
System OK

May 07, 2017 | Cars & Trucks

1 Answer

My 2008 GMC AcadiaSLT2 that is having all sorts of electrical issues. ServiceStabilitracLight on,Traction Control off light, Oil pressure low stop engine. Throws codes P0017,P0016,P0102,P0113,P0700.


DTC P0016: Crankshaft Position (CKP) - Intake Camshaft Position (CMP) Correlation Bank 1

DTC P0017: Crankshaft Position (CKP) - Exhaust Camshaft Position (CMP) Correlation Bank 1
A camshaft actuator stuck in the full actuation position may cause the engine to crank but not start.
The camshaft position (CMP) actuator system is an electro-hydraulic operated device used for a variety of engine performance and operational enhancements. These enhancements include lower emission output through exhaust gas dilution of the intake charge in the combustion chamber, a broader engine torque range, and improved fuel economy. The CMP actuator system accomplishes this by changing the angle or timing of the camshaft relative to the crankshaft position. The CMP actuator simply allows earlier or later intake and exhaust valve opening during the four stroke engine cycle. The CMP actuator cannot vary the duration of valve opening, or the valve lift.
During engine OFF, engine idling conditions, and engine shutdown, the camshaft actuator is held in the park position. Internal to the CMP actuator assembly is a return spring and a locking pin. During non-phasing modes of the camshaft, the return spring rotates the camshaft back to the park position, and the locking pin retains the CMP actuator sprocket to the camshaft. The park position for the CMP actuator and camshaft is 8.5 degrees before top dead center (BTDC), which is equal to 17 crankshaft degrees BTDC. The engine control module (ECM) can only command the CMP actuator to retard the valve timing from the park position, or advance the valve timing back to the park position. The total range of valve timing authority is approximately 20 degrees of camshaft rotation, which is equal to 40 degrees of crankshaft rotation.
Problems with this will cause the PCM to disable traction control and Stabilitrac .How many miles on your vehicle ?
Chevy Colorado P0017 Case Study Part 1 GM is a GM , Chevy , GMC , Buick , Cadillac etc.....

Jan 15, 2017 | 2008 GMC Acadia SLT-2

1 Answer

Where is cam shaft sensor located on a 08 saturn aura


Which engine ? This vehicle had option of six different engines , 2.4 , 3.5 , 2.8 , 3.0 , 3.2 , 3.6 And are you picking on the right part ? What code > DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit

DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit
It may not even be a cam sensor problem !
DTC P0340: Intake CMP Sensor Circuit

DTC P0365: Exhaust Camshaft Position (CMP) Sensor Circuit
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance

DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance
Camshaft Position (CMP) Actuator System
The camshaft position (CMP) actuator system is an electro-hydraulic operated device used for a variety of engine performance and operational enhancements. These enhancements include lower emission output through exhaust gas dilution of the intake charge in the combustion chamber, a broader engine torque range, and improved fuel economy. The CMP actuator system accomplishes this by changing the angle or timing of the camshaft relative to the crankshaft position. The CMP actuator simply allows earlier or later intake and exhaust valve opening during the four stroke engine cycle. The CMP actuator cannot vary the duration of valve opening, or the valve lift.
During engine OFF, engine idling conditions, and engine shutdown, the camshaft actuator is held in the Park position. Internal to the CMP actuator assembly is a return spring and a locking pin. During non-phasing modes of the camshaft, the return spring rotates the camshaft back to the Park position, and the locking pin retains the CMP actuator sprocket to the camshaft


It may

Jul 06, 2016 | 2008 Saturn Aura

1 Answer

P0014 Diagnostic code, already replaced camshaft actuator & oil twice


code p0014 - Chevy TrailBlazer, TrailBlazer SS and GMC Envoy Forum

forums.trailvoy.com > ... > OEM Issues

Sep 8, 2007 - 11 posts - ‎8 authors
On my Trailblazer I have a code P0014 . this says Camshaft Position Actuator B ... If the desired and actual cam phase angle error exceeds its ... This diagnostic procedure supports the following DTC: ... replace the camshaft actuator solenoid, change the engine oil and filter, ... 2004 Chevy TrailBlazer LT P0014 - Camshaft Position Actuator Solenoid "Relearn"
11 posts
Dec 11, 2009
cam crank sensor mismatch
11 posts
Jul 4, 2009
More results from forums.trailvoy.com

Tech Code "dtc P0014" 2003 Trailblazer - Chevy S-10/Blazer ...

www.gm-trucks.com/.../72278-tech-code-dtc-p0014-2003-trailblazer/

Dec 31, 2007 - 14 posts - ‎6 authors
Tech Code "dtc P0014" 2003 Trailblazer - posted in Chevy ... it had been serviced before for the same thing in 2003 or 2004! ... replace the camshaft actuator solenoid, change the engine oil and .... The extended war. co. prob. would not be to happy since they already fixed the sensor once or twice already.

Replace a Camshaft Position Actuator Solenoid Valve on a ...

? 8:05
https://www.youtube.com/watch?v=4Dkdd287AKg

Jan 11, 2016 | 2004 GMC Canyon

1 Answer

P0011 VW code


P0011 Volkswagen - 'A' Camshaft Position Timing Over-Advanced Or System Performance Bank 1 ' Add Comment
Possible causes
- Dirty engine oil
- Low engine oil level
- Camshaft actuator circuit open or shorted
- Camshaft actuator circuit poor electrical connection
- Faulty camshaft actuator

Apr 13, 2015 | Volkswagen Cars & Trucks

1 Answer

2006 solstice coded to replace camshaft actuator valves, cleared codes, 2 days later service engine light came on again


More than likely you need to replace the cam phaser itself it only comes on do to lack of oil pressure to the motor ( like not changing your oil regular or running the car extremely low on oil)

Oct 29, 2013 | 2006 Pontiac Solstice

1 Answer

Check engine light code p0014 exhaust and p0015 exhaust


P0015: Camshaft Position, Act B - bank 1, timing over

P0014: Camshaft Position, Act B - bank 1, timing over advanced
Check oil level and quality.
Remove n clean exhaust camshaft vanost actuator.
Do not refit to exhaust cam, but swap with inlet actuator.
clear codes...if eml on again see if fault moved to inlet cam. If so replace the actuator.

Jul 25, 2013 | 2007 Mini Cooper

1 Answer

Volkswagen passat wagon 2004 codes p0300 p0302 p0304 p0011 runs fine


You have random misfire codes as well as misfires detected on cylinders #2 and #4. P0011 is likely the root cause of the misfire being detected
P0011 VOLKSWAGEN - 'A' Camshaft Position Timing Over-Advanced Or System Performance problems.

Possible causes- Dirty engine oil
- Low engine oil level
- Camshaft actuator circuit open or shorted
- Camshaft actuator circuit poor electrical connection
- Faulty camshaft actuator

There may be a factory bulletin on this code, check with the VW dealer on that. Possible defective Camshaft actuator.

Oct 08, 2012 | 2006 Volkswagen GTI

2 Answers

Ml350 replaced a/b cam position sensor reset computer & and erra codes p0016/p0016 check engine ligth is reset car drives with light off when engine is turn off and started the light goes out if you...


P0010....'A' Camshaft Position Actuator Circuit (Bank 1)

P0011....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0012....'A' Camshaft Position - Timing Over-Retarded (Bank 1)

P0013....'B' Camshaft Position - Actuator Circuit (Bank 1)

P0014....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0015....'B' Camshaft Position -Timing Over-Retarded (Bank 1)

P0020....'A' Camshaft Position Actuator Circuit (Bank 2)

P0021....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0022....'A' Camshaft Position - Timing Over-Retarded (Bank 2)

P0023....'B' Camshaft Position - Actuator Circuit (Bank 2)

P0024....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0025....'B' Camshaft Position - Timing Over-Retarded (Bank 2)

I think your sensors are pattern parts and the readings /resistances are not the same as the original parts ,try some bosch units is my first suggestion ,

Nov 02, 2010 | Mercedes-Benz ML350 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

448 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

xxxxxx xxx

Level 3 Expert

4862 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...