Question about 1986 Nissan 300ZX

1 Answer

Inside lights My inside lights dont come on when opening door. But when you put the key in the ignition they will. I have adjusted the over head switches for door, but doesnt seem to work? Any assistance would help.

Posted by on

  • johnnynjon Aug 14, 2008

    I have and they dont work. When you put the key in the ignition than they do. I would like light when I open the doors though

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 129 Answers

Adjust switches with door closed, engine off

Posted on Aug 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Driver door beeps when open and key is out of ignition. What would cause this and what can I do to correct this?


The problem is in the ignition switch where the key goes there is a sensor that senses key in ignition that breaks and grounds itself causing constant annoying beeping

Sep 07, 2016 | 2002 Isuzu Rodeo

1 Answer

When i put my car in park open the door, light does not illuminate andthe doors dont unlock.and when i turn off the car,and open the door, the stereo contiues to run.what is going on


- ensure the interior light control switch is set to turn on with door.

- the stereo may continue to run if the key is left in the ignition.
25475896-n5jmrotbaomxjbnyrqgjviug-5-0.png

Feb 24, 2015 | Cars & Trucks

1 Answer

Nothing will power up


Have you checked your ignition switch!

Jun 02, 2012 | Mitsubishi Cars & Trucks

2 Answers

My car is bining when I open door, indicates that a light is on or keys in ignition no lights on and no key in ignition, battery is being drained?


There is a good chance your Ignition switch is worn out or an adjustment has slipped. There are a certain amount of functions done at the powerhead of the Ignition switch and some functions are done lower, at the end of the steering column. There will be a rod or cable running the length of the steering column and some are adjustable.

The battery can easily be drained or components can be damaged when left on for 24/7 because the key does not turn off. Try the passengers door to see if the chime goes off when it opens too.
There is a part inside the Ignition switch that detects the key. This means your battery may be fine, just the indicator is broken. There is always a way to tell, but it is easier to replace the switch.

The Ignition switch is not too difficult to replace. It may have some Antitheft screws holding the case to the column. The plastic cover on the column will need to be removed. There is usually a trigger pin hole in the plastic cover. When this pin is push with a drill bit or similar part, the core of the Ignition switch will be released.

I hope you found my Solution helpful.

Jun 28, 2011 | 1999 Ford Windstar

1 Answer

Just wondering if you leave car door open or closed when trying to get security light to go off


YOU CAN TURN OFF SECURITY LIGHT BY PUTTING KEY IN THE IGNITION SWITCH.TURN IGNITION TO ON POSITION,WITH ENGINE OFF.LEAVE KEY IN THE SWITCH IN ON POSITION FOR 10 MINUTES UNTIL SECURITY LIGHT TURN OFF.IF IT DOES.TURN OFF IGNITION SWITCH.WAIT 5 SECONDS THEN TRY CRANKING CAR.IF THIS DONT WORK TRY ANOTHER KEY DO THE 10 MINUTES SWITCH TRICK.IF STILL THE SECURITY LIGHT DONT TURN OFF YOUR THEFT SECURITY SYSTEM IN FAULT THE DEALERSHIP HAS TO FIX AND REPROGRAM NEW KEY IN SWITCH OR BCM CONTROL MODULE..

Sep 13, 2010 | 1999 Oldsmobile Alero

1 Answer

Can not turn key in ignition to the start position.


sounds like the brake pedal lock out switch or the gear selector switch is out of adjustment.

Feb 22, 2009 | 2007 Chevrolet Equinox LS New Cars

2 Answers

Electrical


Go inside the vehicle,dont put key in ignition, leave driver's door open, press the auto lock button on the driver's door, now close door while you are inside and watch on the dash the alarm enable itself, once it stops flashing open the door, this will set off the alarm, lights flashing horn blowing. Now take the key and put it in the drivers door and turn the key to stop the alarm. Now start you vehicle. If you want you can take the glove box apart to get to the vehicle security module to remove it. Dont unplug it unless the vehicle is running (must be running due to back up on computer) unplug the module and you will never have another problem with the security again and it does not effect your powerlocks.

Jul 09, 2008 | 1995 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...