Question about 2001 Isuzu Rodeo

1 Answer

How to remove sump holden rodeo 3.2 v6 98 ute do i need to remove crankcase bolts inside oil pan as one is impossable to get to? is there any specialised tool that I should have ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,187 Answers

There are no special tools. Once I have the car up I use the correct socket to loosen up the bolts. From underneath while the car raised, probably an extension would help for the ratchet to get through the tight space.

Posted on May 20, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the oil pump located


Inside the crankcase. You would need to remove the sump pan to access the oil pick up and oil pump.

Dec 20, 2015 | Cars & Trucks

2 Answers

How do I change the oil pan gasket?


Whether it's an engine oil pan (called the 'sump'' in the UK) or a transmission oil pan the principle is the same on all vehicles.
1. Drain the oil

2. Remove the bolts holding the sump/pan in place:
change-oil-pan-gasket-mcgwfbeeztshkxy1nyom2hsg-4-0.jpg
change-oil-pan-gasket-mcgwfbeeztshkxy1nyom2hsg-4-1.jpg The oil drain plug, though depending on your vehicle it may look different:
change-oil-pan-gasket-mcgwfbeeztshkxy1nyom2hsg-4-3.jpg change-oil-pan-gasket-mcgwfbeeztshkxy1nyom2hsg-4-6.jpgNew gasket held in place with sealant
Use a blunt screwdriver -if needed - and prise the oil pan free. remove all traces of the old gasket from the mating surfaces.

Use a smear of sealant to hold the new gasket in the correct position on the pan - this will hold it in place when you refit the pan.

Push the pan into position and put in a front bolt finger-tight. Then put in a rear bolt finger-tight.

Putting in the bolts finger-tight allows you to gently 'move' the pan if needed to put the bolts in one at a time.

When all bolts are in, tighten them with a wrench/socket. Then check them all again for tightness.

It isn't actually a big job .. more 'messy' because of the oil.

Nov 04, 2015 | Cars & Trucks

2 Answers

How to change 2002 2.8 4bj1 fuel filter


your diesel engine should have a center bolt holding fuel filter it in place.you place drain pan under fuel filter when you remove top center bolt while holding fuel filter then remove old fuel filter then take new fuel filter add few ounces clean diesel fuel in new fuel filter lubricate gasket new fuel filter cartridge then install new filter crank engine check for leaks.

Nov 13, 2011 | Cars & Trucks

2 Answers

2003 holden rodeo auto gearbox. I have taken the oil from the bottom of the sump nut out and have been replacing the oil from the dip stick. Is this correct and how much oil do I replace, or is it just...


Taking the oil from bottom sump is correct n yes putting it back via the dip stick is correct too. But b4 u guage, start up the car, engage gear with leg on the brakes if stationary, try reverse too 4 a while, legs on brakes again if stationary bring to neutral, still on hand brake up. Then guage to d required dip stick mark. Note: b4 starting up n engaging gears be sure u ve put in some oil first n pls do not let it over guage, go past the mark on dip stick, if it does drain a bit at a time till u get it right.

Sep 10, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

How to replace oil pan gasket on 2002 deville


Oil Pan REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the crankcase.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Oil level indicator harness connector, if equipped
    • Exhaust Y-pipe, if needed
    • Transaxle assembly from the vehicle.
    • Oil pan bolts and the oil pan
    To install: NOTE: The oil pan gasket is reusable unless it is damaged. Do not remove the gasket from the oil pan groove unless gasket replacement is required.
  4. Thoroughly clean the inside of the oil pan and the cylinder block contact surface. If the oil pan gasket is being reused, be careful not to damage it. Do not expose the gasket to cleaning solvents.
  5. If a new gasket is being installed, start the gasket into the oil pan groove and work the gasket into the groove in both directions. Once the gasket is exposed to oil, it will expand and no longer stay in the groove without wrinkles. If this condition exists, replace the gasket.
  6. Install or connect the following:
    • Oil pan. Torque the bolts, in sequence, to 89 inch lbs. (10 Nm).
    • Oil level indicator connector, if removed
    • Transaxle assembly, if removed
    • Y-pipe, if removed
    • Flywheel cover, if removed
    • Oil pan drain plug. Torque it to 15 ft. lbs. (20 Nm).
    • Negative battery cable
  7. Refill the crankcase.
  8. Run the engine and check for leaks. Fig. 1: Oil pan bolt torque sequence 7922vg08.gif
prev.gif next.gif

Oct 29, 2010 | 2002 Cadillac Deville

1 Answer

2002 holden rodeo automatic transmision oil capacity


The filter doesn't take any oil, but when they figure the quantity, they figure either filter change or rebuild, the filter change uses about 5 quarts and the rebuild is 12 quarts. I don't have the exact amounts in front of me, but if you need them,I can look them up. Also, I am not familiar with the Holden dual cab, But most automatics are about the same. Hope this helps.

Mar 08, 2010 | 2002 Isuzu Rodeo

1 Answer

Oil sump plug location of holden rodeo 1999


ok.....so when you get under you rodeo....look for a big pan....it should be black in color.......and at the very end of it,,you should see the plug..

but dont get near the tranny or you could end up getting the wrong plug....and you will have cherry tranny fluid all over the place.....

good luck XD

May 14, 2009 | 1999 Isuzu Rodeo

1 Answer

Oil pickup/filter/pump problem with Holden Jackaroo 1993 4x4 V6


the motor will deffinatly have to be pulled. There is not enough room underneath to remove the oil pan.

Feb 04, 2009 | 1993 Isuzu Rodeo

2 Answers

05 susuki forenza


Removal Procedure
1. Disconnect the negative battery cable.
2. Drain the engine oil from the engine crankcase.
3. Remove the exhaust flex pipe retaining nuts from
the exhaust manifold.
4. Remove the exhaust flex pipe retaining nuts from
the catalytic converter or the connecting pipe.
5. Remove the exhaust flex pipe.
6. Remove the oil pan flange–to–transaxle retaining
bolts.
7. Remove the oil pan retaining bolts.
8. Remove the oil pan from the engine block.
Cleaning Procedure
1. Clean the oil pan sealing surface.
2. Clean the engine block sealing surface.
3. Clean the oil pan retaining bolts.
4. Clean the oil pan attaching bolt holes in the engine
block.
5. Clean the oil pan scraper.
Installation Procedure
1. Coat the new oil pan gasket with sealant.
Important : Install the oil pan within 5 minutes after applying
the liquid gasket to the oil pan.
2. Install the oil pan to the engine block.
3. Install the oil pan retaining bolts.
Tighten
Tighten the oil pan retaining bolts to 10 NSm (89 lb–in).
4. Install the oil pan flange–to–transaxle retaining
bolts.
Tighten
Tighten the oil pan flange–to–transaxle bolts to 40
NSm (30 lb–ft).
5. Install the exhaust flex pipe.
6. Install the exhaust flex pipe retaining nuts to the
exhaust manifold.
Tighten
Tighten the exhaust flex pipe–to–exhaust manifold
retaining nuts to 35 NSm (26 lb–ft).
7. Install the exhaust flex pipe retaining nuts to the
catalytic converter or the connecting pipe.
Tighten
Tighten the exhaust flex pipe–to–catalytic converter
or connecting pipe retaining nuts to 35 NSm (26 lb–ft).
8. Connect the negative battery cable.
9. Install the oil pan drain plug.
Tighten
Tighten the oil pan drain plug to 35 NSm (26 lb–ft).
10. Refill the engine crankcase with engine oil.

Jun 14, 2008 | 2005 Suzuki Forenza

Not finding what you are looking for?
2001 Isuzu Rodeo Logo

Related Topics:

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...