Question about Mitsubishi Minivan

1 Answer

The car does not simply move faster even if you press the accelerator what part that need to repair

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Teacher:

    An expert who has written 2 tips or uploaded 1 video tip.

  • Expert
  • 171 Answers

Dear,

get the fuel pump checked and callibrated to get the maximum output,

get the wheels greesed too for frictionfree work

thanx

Posted on May 20, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The car does not move faster when i step ******* the accelerator


run fault codes and check for accelerator position sensor /MAP/MAF sensors

Dec 13, 2013 | 2001 Toyota Sequoia

1 Answer

Nissan pathfinder cutting out


I read somewhere that the problem was related to the sensor in the brake pedal, when it goes bad it confuses the computer, no input to indicate that the brake was applied, so it basically goes into limp mode, press the accelerator all the way to the floor and you get only gradual acceleration.

Oct 23, 2017 | 2001 Nissan Pathfinder

1 Answer

I have a 2005 automatic ponatic gram when check engine flashes and my trac light is onit wont accelerate even when i push the petal down then it will just catch and go alittle faster also when i come


I am assuming you have a Pontiac Grand Am.
You would need to have someone scan the computer for trouble codes to proceed. The codes will point you in the direction of the problem but not tell you what to replace or repair.

Aug 23, 2012 | Cars & Trucks

2 Answers

The power drive light is on my 2001 honda passport and i don't know what it means


it means you pressed the power drive button. it should be by your shifter knobb or on your shifter knobb itself. you should turn it off asap because in the freeway, it makes the transmission downshift to create more power for acceleration. in other words, it lets you accelerate faster on the freeway, just a little bit, but puts more stress on your engine if you dont turn it off after it downshifts. hope this helps, and goodluck.

May 21, 2011 | 2001 Honda Passport

3 Answers

Accelerator catches/sticks when depressed. You must then press very hard to get it past that point.


go under the hood and manually move the accelerator to see what is binding it.

If you dont know how to do this then get an assistant to press on the accelerator (car does not have to be on) and whatch for the part that moves as he accelerates. Manually move this to find the binding. Please note that it is possible to have binding with in the cable assembly back to the foot pedal.

Good luck

Mar 10, 2010 | 2005 Buick LeSabre

1 Answer

I have a 1996 gmc sierra. It is not shifting properly. It will start going and rpms will just keep rising and then I have to let off gas for it to chage. Then I have to be carefull how much I press...


The torque conveter sound like your best option. It may not be pumping enough fluid to move and lubricate the gears in your transmission. Happened to me before. Check and see if your trans fluid is burnt up. My best bet would be that you may need a new trans.

Oct 17, 2009 | 1999 GMC Sierra 3500

1 Answer

Rhythim dull noise wshen accelerating


well,if it doesnt change with the wheel turned a little it might be a rear wheel bearing or even a couple of loose lugs on a wheel,or even a brake pad worn down to the rivets,can u give a better description of the noise? (metallic,dull thumping,etc...)

Sep 06, 2009 | 2001 Toyota Corolla

1 Answer

When i accelerate car hesitates


just wondering,, when you accelerated you say the needle went up ,,but did the car kinda splutter, or not pull away at all when you accelerated,,,if the needle goes up but the car doesnt seen to pull away then that sounds like a clutch slipping,,.. but if it just hesitates it could be lots of things ,,maybe a dodgy airflow meter..that can also make the car hesitate,,hope that helps you,,,,,

Apr 24, 2009 | 2002 Volvo S60

1 Answer

Engine drops speed when I press gas pedal


Ignition distributor caused problem. Rotor element needs replacement.

Jul 21, 2008 | 2002 Mitsubishi Lancer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...