Question about 2005 Hyundai Tiburon

1 Answer

Is there much work to remove the front end on a 2005 tiburon? need to install license plate and the holes are only large enough for a screw, it must be stripped, because they dont grab, and im afraid to use larger screws that may crack the mold, or even fall off and then i lose my plate.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,489 Answers

Go ahead and use 1 size larger screw. The bumper cover is very resiliant to this. When we put plates on at the dealer, usually we don't even drill a hole. Just screw them in.

Posted on May 20, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a rear license plate bulb in 2004 Jeep Liberty?


  1. Remove the screws that secure the license plate lamp assembly to the rear bumper fascia
  2. Pull the license plate lamp assembly down and out through the mounting hole in the rear bumper fascia far enough to access and disconnect the wire harness connector.
  3. Remove the license plate lamp assembly from the rear bumper fascia.

Apr 16, 2011 | 2004 Jeep Liberty

1 Answer

Tag light is not working. is there a fuse that will get the light turned back on?


The fuse labeled REAR PARK LP 15A in the right instrument panel fuse box powers the rear park lamps, and the tag lamps. If your rear park lamps are working then you most likely need to replace the tag lamps (bulbs). Use the following procedure to replace the lamps.

To Remove:
  1. Remove the two mounting screws from the license plate lamp.
  2. Remove the license plate lamp from the rear bumper fascia.
  3. Remove the license plate lamp socket by turning it counterclockwise.
To Install:
  1. Install the license plate lamp socket by turning it clockwise.
  2. Position the license plate lamp to the rear bumper fascia.
  3. Install the license plate lamp mounting screws.

Feb 17, 2011 | 2004 Chevrolet Impala

1 Answer

How do you replace license plate bulb 2005 cadillac srx


Hi,
First you have to take out the one and only screw in the rear hatch door - it's where the hand pull down is you use to close the hatch.
Then you have to pop all the plastic clips all the way around the plastic door panel, trying not to pull them out from the frame . If you do pull out the white plastic plugs from the frame you better make certain you take them off the plastic housing and insert them back into their frame holes - or you will never get the housing back on.

Once you have the housing loose disconnect the inside tail gate light wire to remove the whole thing. Then you have to remove 7 to 8 nuts from the back of entire License plate, back up bulb housing using a deep socket to get in there. Work it loose from the rear of the car and it will come out just enough to work on the lights.
This is tricky since the screw mounts don't give you much room to work with.

Once you have the license plate and back up bulb frame loose you will see the two housings for the license plate bulbs on top.

Slide out the license plate bulb lens and twist the bulb connection to remove the bulbs.
Replace both of them - you don't want to do this again in a month when the other one blows.

OPTIONAL:
Once you take out the bulbs you might see that the housing is melted where the bulb wanted to burn through. Drill two small holes one is each end of the housing before I put everything back together to release some of the heat.


Reverse the whole process to put everything back together. It's not easy.
Make sure you insert the cables through the opening for the hatch handle or it will kink and not work properly.

The bulbs come in a two pack of cost $4.95 .

Take care

Jul 28, 2010 | Cadillac SRX Cars & Trucks

1 Answer

How to install a license plate on the front of my


Remove the screws and stick your tag right over the other one,and put the screws back. Or remove the old tag and just use the holes for the new one. Hope this helps.

Apr 02, 2010 | 2002 Pontiac Grand Prix

1 Answer

Rear liscese plate bulbs on 05 cadillac srx


First you have to take out the one and only screw in the rear hatch door - it's where the hand pull down is you use to close the hatch.
Then you have to pop all the plastic clips all the way around the plastic door panel, trying not to pull them out from the frame . If you do pull out the white plastic plugs from the frame you better make certain you take them off the plastic housing and insert them back into their frame holes - or you will never get the housing back on.

Once you have the housing loose disconnect the inside tail gate light wire to remove the whole thing. Then you have to remove 7 to 8 nuts from the back of entire License plate, back up bulb housing using a deep socket to get in there. Work it loose from the rear of the car and it will come out just enough to work on the lights.
This is tricky since the screw mounts don't give you much room to work with.

Once you have the license plate and back up bulb frame loose you will see the two housings for the license plate bulbs on top.

Slide out the license plate bulb lens and twist the bulb connection to remove the bulbs.
Replace both of them - you don't want to do this again in a month when the other one blows.

OPTIONAL:
Once you take out the bulbs you might see that the housing is melted where the bulb wanted to burn through. Drill two small holes one is each end of the housing before I put everything back together to release some of the heat.


Reverse the whole process to put everything back together. It's not easy.
Make sure you insert the cables through the opening for the hatch handle or it will kink and not work properly.

The bulbs come in a two pack of cost $4.95 .

Nov 24, 2009 | 2005 Cadillac SRX

1 Answer

1999 Dodge Neon rear license Plate bulb


LICENSE PLATE LAMP BULB
REMOVAL
  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Oct 08, 2009 | 1999 Dodge Neon

2 Answers

I need to hang a Front license plate ..is there a way to do it


DEALERSHIP SELLS A KIT TO MOUNT IT ON THE CAR IF IT IDNT COME WITH ONE CALL YOUR LOCAL G.M DEALER

Aug 24, 2009 | 1989 Oldsmobile Eighty Eight Royale

2 Answers

Back door latch broke cant open back door where can i buy the part and the name of the part


I just bought the part last week for 61.76 from the dealership. It takes about two hours to unscrew the strap from the inside, remove trim from the inside starting at the top, sides and bottom. Remove the license plate from the outside of the hatch. Next remove the 8 bolts (10mm)and 3 white plastic tabs that snap on from the large black plate and move to the side (you don't need to disconnect the wires). From here you can reach around the rear window unit and open the door by moving the latch or pulling the cable. You should remove the 4 nuts that hold on the rear window assembly and move the to reach two nuts which holds the center portion of the trim piece you are trying to remove. There should be a plastic piece covering the cable and latch, it just pops off by pulling it straight out. There are three plastic tabs in the corners and one screw (lock for the hatch) that holds on the license plate assembly to the rear hatch along with two white plastic tabs which are located at the bottom two holes for license plate. These plastic tabs come in from the front. Use pliers to squeeze the together and push. You will need to disconnect the license plate lamp wire connector from the left side. The license plate assembly should drop away. Two screws hold on the latch, remove and replace and reverse proceedure.

Jul 08, 2009 | 2002 Toyota Sequoia

1 Answer

Front license plate mounting -- how to


well u will have to drill holes though the bumper and use the supplied screws that came with the kit u might have to use washers on both sides of the screws of the license plate but that should work for ya

May 02, 2009 | 2003 Mitsubishi Eclipse Spyder

1 Answer

Add front license plate, do I need to remove bumper to get behind


try using self tapping screws so you dont have to remove it, you can drill pilot holes if the screw wont go thru easy, and you dont need a nut/bolt

Mar 20, 2009 | 1998 Honda CR-V

Not finding what you are looking for?
Cars & Trucks Logo

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...