Question about Chevrolet Equinox

1 Answer

My 2005 equinox keyless entry doesn't work anymore any way to reprogram this one are will I have to order another one and have the dealer to program it

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

If it is a new transmitter, you must take it to the dealer.
If the transmitter has already been programmed once and lost synchronization (dead fob battery, etc.), you can hold lock and unlock for 7 seconds while you are close to the vehicle. If this works, the door locks should cycle.

Posted on May 20, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 toyota 4runner keyless remote doesn't work


Check with a Toyota dealer for your info

Aug 30, 2012 | 1999 Toyota 4Runner

1 Answer

My keyless entry is not working. the lock switch in the car operates the locks just fine. my key fob has a brand new battery and the light blinks when I press the lock/unlock button. My vehicle is a 2005...


probably sensor for keyless entry,but would not advise u too get this from a junk yard as the sensors are vin specific,will put ur car into anti-theft mode then u will have to replace the body control computer,have a dealer order u a keyless entry sensor vin specific for ur car,these are usually under dash up top middle area its a little black box,will have to remove dash pad or dash to replace.

Aug 21, 2011 | 2005 Honda Civic

1 Answer

Keyless entry has a hard time unlocking the doors. Have already replaced the battery.


sometimes the key fob gets worn out due to being used constantly it may need to be replaced.sometimes they may need to be reprogrammed with the entry module and sometimes the entry module has a problem and needs to be replaced.the only way to find out is to take it to a shop that has the capability to do this work or the dealer.

Apr 05, 2011 | 2005 Chevrolet Malibu

1 Answer

My keyless entry does not work anymore


Step by Step Solution:
1. Check the battery in your Key Fob/Remote, Replace?
2. If after replacing battery and still does not work then may have lost programming, or bad keyless entry module.
3. May need to take to dealer to have programmed or keyless entry module replaced.

Sep 15, 2010 | 1995 Buick Regal

1 Answer

How do reprogram my keyless entry pad to a 1995


look in your owner manul it should tell you . or go to a dealer they will be abele to tell you

Nov 11, 2009 | 1995 Ford F350

1 Answer

Keyless entry not working. 2010 equinox


reset itself. may have been something obstructing rear gate from closing all the way.

Sep 30, 2009 | 2009 Chevrolet Equinox

1 Answer

Keyless entry wont work 2002 chevy s10


The only way to program them is with a scan tool so you'll need to visit your local dealer to have it done. Here is how it is done.

  1. Install a scan tool.
  2. Use the scan tool in order to access programming: Vehicle Control System/Computer Integrating System/Module Setup/BCM/Program Key Fobs.
  3. Press the START soft key on the scan tool. Important: The scan tool must stay connected until all of the transmitters are programmed.
  4. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of 5-10 seconds, the scan tool will indicate that the transmitter is programmed.
  5. Repeat the previous step in order to program up to 4 transmitters.
  6. Remove the scan tool.
  7. Operate the transmitter functions in order to verify correct system operation.

Sep 02, 2009 | 2002 Chevrolet S-10

1 Answer

Keyless entry remote doesn't work with old or new batery. If sensor is bad where is sensor and how do you know if sensor is prolem with keyless remote.


I had the same problem. Went to dealer who said it probably needed to be reprogrammed (around $45-50). Paid for premium assistance with FixYA. Ginko gave me the procedure to reprogram my remotes. It was very easy and worked great. Now both of my remotes are working and it only cost me $9.99.

JOECOV

Jul 29, 2008 | 1999 Buick Century

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

233 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...