Question about Ford F-250

1 Answer

Fuel gauge is full always - F-250 Ford Cars & Trucks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Your gauge has gone out my need a new cluster

Posted on May 20, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my crysler 1996 reads fuel gauge full when it is empty


The fuel level sending unit inside the fuel tank is bad or the gauge is or there is a wiring problem This video is for a mercury vehicle , but all makes an models are the same . Repairing Fuel Gauge Problems 2004 Mercury Marquis EricTheCarGuy

Mar 17, 2015 | Cars & Trucks

1 Answer

Fuel gauge registers full when ignition is switched on


Bad fuel sender unit or fuel sender wiring

Feb 03, 2013 | 1989 Jeep Wrangler

1 Answer

1998 chevrolet astro van/fuel gauge always stays on full


Usually a sign of a faulty sending unit in the tank.
A mechanic would ground the wire to the sender to see if the gauge moves.

Jul 09, 2012 | Chevrolet Astro Cars & Trucks

1 Answer

Why does the fuel gague in my 1988 Honda accord always read full?


check to see if your fuel gauge is working by disconnecting the fuse from the panel, if gauge reads e then ground the fuel gauge if it reads full then the fuel gauge reads fine the its the float sensor in the fuel tank. good luck have fun

Oct 21, 2011 | 1988 Honda Accord 4 Door

1 Answer

Fuel gauge shows full!


this problem is caused by a defective fual gauge sending unit inside the gas tank.

Mar 15, 2010 | 2002 Nissan Sentra

1 Answer

92 k1500 5.7L tbi fuel gauge always reads full and temp gauge always stuck down.... any suggestions


Two possible problems.... the temp gauge wire is a single green wire attatched to the driver's side head (no1 bank) near the front in the side (in front of plug #1) ground it and your gauge should go to full hot,,, same with the fuel gauge, if you unplug it at the tank it should go to empty, or visa versa... if the gauges respond, replace the sending units, if they don't, replave the instrument panel

Sep 12, 2009 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Fuel Guage Goes To Full


if you have pulled the sending unit wire from the sending unit the gage in the dash is bad .

Sep 04, 2009 | 1996 Ford F150 Regular Cab

2 Answers

Fuel gauge stuck on full for my 2000 ford taurus SE


it is probbally the fuel pump in the gas tank. It has a float like the one in your toilet and a sensor attached to it to tell you how much gas you have.

Aug 08, 2009 | 2000 Ford Taurus

1 Answer

1989 Saab 900 low level fuel light


You don;t say whether the fuel gauge is reading accurately, or whether it's always on empty. If the gauge is always showing empty, it's most likely a problem with the sending unit in the fuel tank. Check the resistance across the two terminals of the sending unit.

On a C900, the fuel sender level unit is separate from the fuel pump and located on the right side top of the tank, accessible by removing the trunk floor lift up panel (the pump is located on the left side top of the tank.
Possible problems are: electrical line off or broken, float not working (it's fairly delicate); or gauge not working.

Test the resistance of the sending unit with the lines disconnected, the resistance should be 2.6 to 3.8 ohms full tank, 63.3 to 67.5 ohms empty tank; and test for voltage across the top of the sender unit, if no voltage, that's likely the problem!

If the gauge is otherwise reading accurately (showing 'full' for a full tank, etc) then the problem is likely a gauge malfunction and can be simply replaced.

Good luck!

Saabreur

Jul 10, 2008 | 1989 Saab 900 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...