Question about 2005 Lincoln Aviator

1 Answer

Power door lock switch on drivers side malfunctions...

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 4,369 Answers

Check fuses in panel uder left side of dash, chart in owner manual.

do locks work from passenger side?

with key fob?

With door keypad, if equipped?

Posted on May 20, 2011

Testimonial: "thank you."

  • gerry bissi May 20, 2011

    they go through the door into the area by the kick panel, on dirver side floor area. It could be the switch, but you need to remove switch to check for 12 volts at wire to switch. I will try to look at circuit tomorrow.

  • gerry bissi May 20, 2011

    Does it just not lock/umlock while the vehicle is in moving?



    remove the 2 screws holding the door switches in place and check to be sure all 3 connectors are fully seated.



    it may be the vehicle security module which controls all these locks. A delaer can check for DTC codes with his scanner. probably a half hour labor charge. But, check these fuses first. Fuse chart in owner manual. Report back.



  • Battery junction box (BJB) fuse(s): (under hood)

    • 1 (60A)
    • 2 (30A)
    • 29 (60A)

  • Central junction box (CJB) fuse(s): (under dash)

    • 2 (10A)
    • 23 (7.5A)

  • Circuitry
  • Relays
  • Remote keyless entry (RKE) transmitter
  • RKE keypad
  • Vehicle security module

  • ---------------------------------------------------------------------------------------------------------------

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Problem with power door lock


Try looking for the drivers door switch online or at your local salvage yard...Try GM partsNOW online...

Jul 08, 2016 | 1994 Chevrolet Cavalier

1 Answer

I have a 2005 Chevy extended cab 1500 and the controls on my driver side door aren't working. The door is saying it ajar when it's closed. I can't roll the windows up or down. Is it the master switch?


How to fix the Chev power window door lock switch - YouTube

? 5:04
https://www.youtube.com/watch?v=XDKaDURD8Sc
Jul 13, 2013 - Uploaded by spelunkerd
How to fix the Chev power window door lock switch ..... Some time later my drivers side window stopped working in the down position. ... These intermittent electrical problems are frustrating,aren't they? .... How To Install Replace Door Locks Chevy GMC Truck Silverado Sierra Yukon Tahoe Suburban ...

Diagnose Power Door Locks Dont Work Properly - Auto ...

www.auto-repair-help.com/.../diagnose_power_door_locks_dont_work_...
An inoperative power door lock can be caused by the switch, solenoid, wiring problem or ... Hi, I have a 2005 Nissan Sentra and the power locks aren't working. .... Hi, mypassenger door locks/unlocks both doors but my driver side door works independently and .... I have a 1986 Chevy Silverado K10 with auto door locks.

SilveradoSierra.com • 2003 silverado no power in right door ...

www.silveradosierra.com/.../2003-silverado-no-power-in-right-door-t30...

Dec 26, 2015 | Cars & Trucks

1 Answer

Door lock dont always work


What door lock doesn't always work ? One or all of them . This is a complex set up for these door locks ! The switch is an input to the BCM - body control module . There is logic involved in the microprocessor , there are relays built in to the BCM ! Could have a DTC - diagnostic trouble code stored in the BCM ! Could be a bad connection at the BCM or master window switch ! A bad ground !
The power door lock system consists of the following components:
?€¢
Body control module (BCM)


?€¢
DOOR LKS fuse


?€¢
Driver door lock actuator


?€¢
Driver door lock switch


?€¢
GMLAN serial data link


?€¢
Keyless entry transmitter


?€¢
Passenger door lock actuator


?€¢
Passenger door lock switch


?€¢
Remote control door lock receiver (RCDLR)


The DR LCK fuse supplies battery voltage to the body control module (BCM) for the power door lock system. The BCM supplies and monitors a reference voltage to the driver and passenger door lock switches through the door lock switch lock/unlock signal circuit. Each door lock switch receives ground at G300 which is also the ground for the door lock and unlock relays located in the BCM. When a door lock switch is placed in the lock position, the reference voltage is switched to ground and the BCM senses 0.0 volts on the door lock/unlock signal circuit. When a door lock switch is placed in the unlock position, the reference voltage is switched to ground through a 1.5k ohm resistor that is internal to each of the door lock switches and the BCM senses approximately 2.9 volts on the door lock/unlock signal circuit. The BCM interprets what position the activated door lock switch was placed in based on the voltage drop.
The BCM, upon receipt of a lock or unlock switch signal, will switch the appropriate door lock/unlock relay coil control circuit to ground causing the appropriate door lock/unlock relay to energize. With the relay energized, voltage is applied to the door lock actuator control circuit causing the door to either lock, or unlock depending on what command was received from the power door lock switch or remote control door lock receiver (RCDLR). When a power door lock/unlock relay is not energized, the switch contacts are normally grounded through the BCM which provides ground to the appropriate door lock actuator for the lock/unlock function being performed. The power door lock/unlock functions are performed by reversing the flow of voltage through the door lock actuator control circuits. The BCM has three internal drivers for the power door lock system. Driver door unlock, passenger door unlock and all door lock. This is done to isolate the driver door lock actuator so it can be unlocked separately from the passenger door. For additional information concerning keyless entry, refer to Keyless Entry System Description and Operation.
This is one you may want to take to dealer or some other ASE certified repair shop ! To do this right you need a Tech 2 scan tool !
Ignition ON, observe the scan tool Door Lock Switch parameter while using the driver and passenger door lock switches. The parameter should change from Idle to Lock and Unlock.
?‡'
If the value does not change, refer to Door Lock Switch Malfunction.

Command the doors to LOCK and UNLOCK with the scan tool, the door lock actuators should LOCK and UNLOCK when changing between the commanded states.
?‡'
If one or more doors do not LOCK or UNLOCK, refer to Door Lock Malfunction.

Aug 12, 2015 | 2009 Pontiac Solstice Convertible

2 Answers

What causes a malfunction in power locks?


The power door locks are controlled by the BCM -body control module ! The door lock switch is an input to the BCM .
The BCM, upon receipt of a door lock switch lock or unlock signal, will switch the appropriate door lock actuator control circuits to battery positive voltage. The opposing side of the door lock actuators are connected to ground internally within the BCM through the other door lock actuator control circuit and the doors will lock or unlock appropriately.
First thing to do would be check power an ground circuits at the BCM ! Do you have any other systems not working -power windows etc...
The DR/LCK fuse supplies battery positive voltage to the I/P fuse block for the door lock system. The body control module (BCM) supplies and monitors a reference voltage to the door lock switch through the door lock switch lock/unlock signal circuit. The door lock switch also receives a constant ground source. If a door lock switch is placed in the lock position or unlock position, the reference voltage is taken directly to ground and the BCM detects the voltage drop on the signal circuit.
Should have BCM checked for stored DTC'S - diagnostic trouble codes !
Ignition ON, observe the scan tool Driver Door Lock Sw, Psgr Door Lock Sw, Driver Door Unlock Sw and Psgr Door Unlock Sw parameters while using the driver and passenger door lock switches. The parameters should change between Active and Inactive.
?‡'
If the values does not change between the commanded states, refer to Door Lock Switch Malfunction.

Command the driver door and passenger door lock actuators to LOCK and UNLOCK with the scan tool, the doors should LOCK and UNLOCK when changing between commanded states.
?‡'
If a door lock actuator does not perform the LOCK and UNLOCK functions, refer to Door Lock Malfunction


DTC B3130 00: All Door Unlock Circuit

DTC B3135 00: All Door Lock Circuit

Aug 09, 2015 | 2010 Chevrolet Impala

5 Answers

Hello I have a 1997 Honda civic ex coupe manual trans, my issue is that the power lock won't work and the passenger side window doesn't work either, the only one working is the driver side power window...


Most probable cause , ,,, when you open & close the door, the wires in the rubber boot (accordian like) harness in between the door hinges, get cut and will cause alot if issues, without burning a fuse !

Oct 25, 2014 | 1997 Honda Civic

1 Answer

Both rear electric door locks are malfunctioning. Drivers side rear door lock works good when it is cold. the same was true with the passenger rear door lock. now that one will not work at all. the...


to see if it is a switch problem see if the locks work from their respective doors, if the locks work from the switch's on the back doors and not from the drivers switch then the drivers switch is bad. If the locks don't work right from any of the switches then the door lock solenoids are bad. the solenoids are not too hard to change if you are mechanically inclined, switches are not too hard either

Feb 09, 2014 | 2008 Chevrolet Impala

1 Answer

Power locks don't work with remote or control from


The door lock/unlock input from the driver's key switch goes to the Door Multiplex control unit (main switch), the Door multiplex control unit then sends a signal on the BUS (CAN) circuit to the passenger's multiplex control unit; the passenger's multiplex control unit then controls all the door locks. The passenger's door lock key switch inputs to the passenger's multiplex control unit, if the locks work from the passenger's side key switch but not the driver's side key switch, the most likely cause is the driver's multiplex control unit (main switch) not sending the signal to the passenger's side multiplex control unit. This could also be the drivers side door lock actuator. Hope this helps!

Jan 07, 2010 | 2003 Honda Pilot

1 Answer

2002 Ford Explorer - Drivers side door lock, rear


Aside from the fuses, your drive side power door lock may be failing to work because of a bad door-lock relay system, or, alternatively, the locking switch/button, itself, is not malfunctioning and in need of replacement.

A great handyman site that specifies the above probable causes and more is the following link:
http://yourhandymanzone.com/Your_Handyman_Zone_How_To_Pages_Vehicle_Car_Zone_Cars_Trucks_Vans_Locks_Power_Locks_Do_Not_Lock_When_Pressing_Locking_Switch_Button.htm

Good luck!

Jul 18, 2009 | 2002 Ford Explorer

1 Answer

Electric door lock not working


Any of these three causes may apply to your situation of your driver's rear door not power locking, specifically the malfunctioning of the 1) relay system, 2) switch motor, or 3) the switch/button itself. Here's a handy diagnostic article that explains this:
http://yourhandymanzone.com/Your_Handyman_Zone_How_To_Pages_Vehicle_Car_Zone_Cars_Trucks_Vans_Locks_Power_Locks_Do_Not_Lock_When_Pressing_Locking_Switch_Button.htm

This should lead you to the correction of your door's failure to lock.

Brad

Jun 01, 2009 | 2004 Dodge Ram 2500

Not finding what you are looking for?
2005 Lincoln Aviator Logo

446 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...