Question about Isuzu Rodeo Sport

1 Answer

2001 rodeo sport 6cyl auto trans first start up and this is not every time the vehilce will sputter then when you start to drive at about 2000 rpms the check engine light flashes but it will never set a dtc code if you let off the gas and go below or above 2000 rpms the light stops flashing.

Posted by on

  • bonzee84115 May 26, 2011

    I have had the vehicle scanned while the check engine light is flashing and when its not the problem is it never sets or stores a code it seems to act up when its warm outside now here is the kicker if you shut the vehicle off wait a few min and restart no problems at all.


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Isuzu Master
  • 14,585 Answers

When the light flashes, it is indicating that you can damage the emissions part of the system. ie... catalitic converter. When the light comes on it does set a code, intermittant, the light might go off , but the code is stored. have this checked. It will lead you/ us in the right direction. As ther are many things that can be wrong to make the light flash. Check this soon because it will only get worse and cause other problems. ie.. nip it in the bud Let me know

Posted on May 20, 2011

  • bonzee84115 May 26, 2011

    I have had the vehicle scanned while the check engine light is flashing and with it off it never sets a code or stores one. the one thing i have noticed is that it seems to act up when its warm outside. so this does not happen all the time. If i shut the vehicle and wait a few min then restart it it is fine.

  • Randy Ohler May 26, 2011

    Then it is likely a wiring problem. First check the wires at the sensors and the ECM by wiggling them at the plugs, If you get the sputter or th engine reacts then you have found a problem. This can be two things, 1 the wires are all most broken at the plug or the pins inside the plug are to loose. The pins can be pushed closer together to make a better contact and the wires will have to be repaired. I start with the ECM. I did one a couple of days ago and had to push/ contract all of the pins in the plug. Solved my problem of misfires and 02 sensor codes.


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you adjust transmission linkage on 2000 isuzu rodeo?

manual or auto
bet automatic. has this.

but really you don't need to read that.
cable off trans.end.
set the transmission to say, drive. position at the t actual trans manual shift lever on side of trans. (the PRNDL switch may be here)
count the detent clicks., (easy huh?) to drive PRND bingo there.
then attach the cable and get it to the Drive marker in the cab console.
the lock it all down.
the test all gears. park and neutral , in drive way, not on road yet.
if all ok, hit the road.

Mar 11, 2015 | 2000 Isuzu Rodeo

1 Answer

2002 isuzu rodeo sport .where is the shift solenoid?

You have two drain the trans fluid and remove the pan and it's inside the trans the pans kind of tricky to remove because of the four wheel drive

Jun 14, 2014 | 2001 Isuzu Rodeo

1 Answer

2001 Isuzu Rodeo Sport Trans

you may have a broken band or a bad solenoid. most parts stores can tell you what the code is did you change trans filter

Apr 19, 2014 | 2001 Isuzu Rodeo

1 Answer

2000 Mitsubishi montero sport limited keeps dying while driving

my monterosport 2001 runs great till you come to a stop sign the rpms drop and it dies start it back up revs itself and rpms drop and it dies. we can start it up rev it and it clearsup and idles but later on when you come to a stop it dies again we have cleaned the egr valave and still same thing could the tps be the problem or what?

Apr 24, 2012 | 2001 Mitsubishi Montero Sport 4WD

1 Answer

Where are the connecters at for checking codes located for a 1997 rodeo with a 3.2 motor and auto trans?

For 1997 Isuzu Truck Rodeo 2WD 3.2L MFI SOHC 6cyl the OBD Diagnostic Link Connector is located: Front seating area, driver side, under dash, mounted above kick panel.

Hope this helps (remembert to rate and comment this answer).

Jul 12, 2011 | 1997 Isuzu Rodeo

1 Answer

2001 Isuzu Rodeo Check Engine Light flashes when accelerating.

I would change the trans flter, trans fluid, and have the linkage on the trans adjusted.

Jul 21, 2009 | 2001 Isuzu Rodeo

1 Answer

Engine issue

Mass air flow meter may be going bad. About a 90 dollar DIY easy project.

Mar 20, 2009 | 2001 Isuzu Rodeo

1 Answer

2001 Isuzu Rodeo Sport will not go forward in drive

whats the fluid smell like? when was the last time it was serviced? where is fluid on stick when hot? low on fluid could do what you discribed, but chances are trans needs rebuilt. if fluid smells burnt, rebuild or replacement.

Jan 18, 2009 | 2004 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

75817 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides