Question about Dodge Spirit

1 Answer

He took off the serpetine belt to change water pump on a 1993 dodge spirit 3 litre motor and now cannot figure out how to get the belt back on.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 252 Answers

Here is a pic for you if it helps please 4 thumbs up and a testimonial thanks

He took off the serpetine - jamiesturm29_1.gif

Posted on May 20, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the water pump on a 93 dodge spirit


Why do you people not even mention WHICH engine it is?
Anyway, on 4-cyl 2.5 L it is on the right side of the engine block (as seen from the driver's position ok?, you need to remove several accesory belts, alternator and a cover and you will see it.

Jun 02, 2012 | 1993 Dodge Spirit

1 Answer

Changed the water pump, put her back together, 3 times now, turns over but won't start. Is there a mode it will go into that I need to reset?


Check for some wires in front of the motor. The Serpetine belt may have caught them and ripped them out when you cranked the engine. There can be a Crankshaft sensor and a Camshaft sensor which is now disconnected.

Its also possible that the water pouring out of your motor has shorted the connector or soaked the Crankshaft sensor. You can try unplugging and cleaning the connector with WD40.

Feb 08, 2011 | 1996 Ford Probe

1 Answer

Thinking about buying a 93 Dodge Spirit 4 cylinder There is no alternator belt on the car as it stands now Can I jump start the car drive it 50 miles home then put on a new belt Have heard that I...


That is correct! With the waterpump not turning, you will destroy the engine within 10 minutes. Make sure all the pullies turn by hand first, then install the belt. The belt routing diagram is usually under the hood. It can also be found in any haynes manual available at most autoparts stores. Hope this helps you. Good luck!

Jan 27, 2011 | 1993 Dodge Spirit

1 Answer

I need the diagram for the serpinetine belt on a 1991 dodge spirit 3.0


The path of pulleys around which the belt goes (beginning with the crankshaft pulley, and moving clockwise around the array of pulleys) is in this order:
tensioner pulley (belt goes around the pulley counter-clockwise)
power steering pulley (belt goes...clockwise)
alternator (belt...clockwise)
idler pulley (belt going under the pulley)
and back to the crank pulley (belt...clockwise).

Feb 28, 2010 | 1993 Dodge Spirit

1 Answer

Need diagram to replace serpetine belt on 1995


should be on the underside of your hoos or on your rad support

Jan 29, 2010 | 1995 Dodge Spirit

2 Answers

Dodge 2005 Grand Caravan water Pump replacement


JUST COMPLETED THIS JOB TODAY. MAKE SURE THE ENGINE HAS COOLED DOWN . IT TOOK APPROX 2 1/2 HRS. DISCONNECT THE NEGATIVE POST ON THE BATTERY. JACK UP PASSENGER SIDE FRONT AND SUPPORT ON JACK STANDS. REMOVE PASS. FROUNT TIRE. DRAIN RADIATOR INTO CONTAINER FOR PROPER DISPOSAL OR REUSE. USING FLOOR JACK PROVIDE SLIGHT TENSION ON OIL PAN WITH A SHORT 2 X 4 WOOD PIECE TO PROTECT OIL PAN. LOOSEN 3 ENGINE MOUNT BOLTS ON PASS. SIDE OF ENGINE COMPARTMENT. ALLOW APPROX 1" BETWEEN SHOULDER OF BOLTS AND MOUNT. LOWER ENGINE UNTILL BOLTS ARE SET ONTO MOUNT. REMOVE ENGINE SPLASH SHIELD INSIDE WHEEL WELL OF REMOVED TIRE. LOCATE WATER PUMP AND LOOSEN 3 PULLEY MOUNTING BOLTS (THIS IS WHILE BELT IS ON PULLEY) REMOVE SURPENTINE BELT AND CONTINUE TO FULLY REMOVE THE PUMP PULLEY. IT WONT COME OUT AS THE PUMP & PULLEY HAVE TO COME OUT TOGEATHER. REMOVE 5 WATER PUMP BOLTS AND CAREFULLY WORK WATER PUMP OUT BETWEEN THE ENGINE AND VEHICLE FRAME. CLEAN ALL MATING/GASKET SURFACES AND BOLTS. USING A SMALL AMOUNT OF TACKY SEALENT TO INSURE THE NEW WATER PUMP SEAL STAYS IN PLACE, THE INSTALL IS PRITTY MUCH THE REVERSAL OF REMOVAL.

GOOD LUCK, REMEMBER TO TIGHTEN ALL BOLTS TO MFR SPECS AND BLEED THE AIR OUT OF THE COOLANT AS REQUIRED.

Mar 30, 2009 | 2005 Ford F-150

2 Answers

Water pump


on the front of the engine. Water pump is located below alternator on passengers side .
It is the part under the alternator, right front corner. 

Mar 07, 2009 | 1993 Dodge Spirit

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...