Question about 2006 Infiniti M35
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Take the wheel off the side with the burnt out bulb. Next pull the 6 plastic rivets out of the front fender well shield. Take the screw out of the shield above the 3 rivets along the inside of the fender edge, Pull the shield back starting at the top where it's tucked under the back portion of the liner shield. Unscrew the top plastic cover, twist the connector counter clockwise and pull it off the bulb. Then unclip the bulb and pull the bulb out noting the groove position for reinstalling the new bulb in the housing. There is nothing simple about your bulb change. The dealer price of the bulb is around $245.00. Don't break the new bulb trying to guess when it's seated properly!
Posted on May 18, 2008
Behind the headlight you should see a eletrical wires running to the headlight section. There will be a 2 inch round plastic ring. You grap the back of the bulb and turn it to the right which will release the bulb and the socket. You pull out the bulb and replace it the same way. If this doesnt help then get back to me.
Posted on Feb 06, 2009
you can access the bulbs from inside the engine compartment. the socker turns about a quarter turn to remove it. do NOT touch the bulb with your fingers as that will shorten the bulb life. you may have to remove the battery to change the one on that side.
Posted on Mar 07, 2009
The adjustment screws/nuts should be located either on the top of the headlamp assembly,
behind the headlamp assembly, or near the frame rail by the radiator
You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well
Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)
For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.
For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.
Posted on Sep 30, 2009
It's really easy to get to the headlight. You have to pull really hard on the whole headlight assembly to pop it off its ball tab. Then unscrew the round back of headlamp and change it. Push the assembly back into place with a lil force. Replace plastic tabs you have to take out to loosen top of bumper and your all done. No need to spend a lot of money at a shop its a do it yourself project.
Posted on Feb 01, 2010
Tips for a great answer:
Nov 29, 2015 | Mazda Cars & Trucks
Apr 15, 2009 | 1999 Ford Taurus
Mar 07, 2009 | 2006 Chevrolet Aveo
Feb 06, 2009 | 2006 Chrysler Sebring
Feb 04, 2009 | 2006 Infiniti M35
Nov 18, 2008 | 2006 Nissan Murano
May 18, 2008 | 2006 Infiniti M35
49 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: